Home › Suspension › FRONT SUSPENSION › FRONT SHOCK ABSORBER › 2013.12–2015.11
RM3160E _53 Suspension _019689 FRONT SUSPENSION _0107981 FRONT SHOCK ABSORBER A

FRONT SUSPENSION  FRONT SHOCK ABSORBER  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1.REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 48609E 2.LOOSEN FRONT SUPPORT TO FRONT SHOCK ABSORBER NUT

a.
C291651

Loosen the front support to front shock absorber nut.

NOTICE:
·

Do not remove the front support to front shock absorber nut.

·

Loosen the front support to front shock absorber nut only when the front shock absorber with coil spring needs to be disassembled.




Hide 55701J 3.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD)

a.
C292275

Disconnect the connector.


b.

Disengage the 6 clamps and separate the wire harness from the outer cowl top panel sub-assembly.


c.
C291652

Remove the 10 bolts, 6 nuts and outer cowl top panel sub-assembly.


Hide 55701J 4.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)

a.
C294592

Disengage the 2 clamps and separate the wire harness from the outer cowl top panel sub-assembly.


b.
C291652

Remove the 10 bolts, 6 nuts and outer cowl top panel sub-assembly.


Hide 5.REMOVE FRONT WHEEL

Hide 89543 6.SEPARATE FRONT SPEED SENSOR

a.
C291653C01
2.51,1.792 2.51,1.531 true 2.438,1.792 2.594,1.958 0.156,0.167 10 true *a
*a Sensor Clamp


Disengage the 2 claws and separate the sensor clamp.


b.

Remove the bolt and separate the front speed sensor and front flexible hose from the front shock absorber assembly.

NOTICE:

Be sure to separate the front speed sensor from the front shock absorber assembly completely.



Hide 48810 7.SEPARATE FRONT STABILIZER LINK ASSEMBLY

a.
C292266

Remove the nut and separate the front stabilizer link assembly from the front shock absorber assembly.

HINT:

If the ball joint turns together with the nut, use a 6 mm hexagon wrench to hold the stud bolt.



Hide 8.REMOVE FRONT SHOCK ABSORBER WITH COIL SPRING

a.
C292288C01
2.052,1.26 2.469,1.26 true 2.302,1.927 2.719,1.927 false 2.729,1.854 3.042,2.01 0.313,0.156 10 false *a 2.479,1.188 2.677,1.365 0.198,0.177 10 true *b
*a Jack
*b Wooden Block
V100135

Front of the Vehicle
V100155

Wooden Block Placement Location


Support the front lower No. 1 suspension arm sub-assembly using a jack and wooden block.


b.
C292267

Remove the 2 bolts and 2 nuts, and separate the front shock absorber with coil spring (lower side) from the steering knuckle.

NOTICE:

When removing the nuts, keep the bolts from rotating.



c.
C292268

Remove the nut, 2 spacers and front shock absorber with coil spring.

NOTICE:

Make sure that the front speed sensor is completely separated from the front shock absorber with coil spring.



Hide 48609E 9.REMOVE FRONT SUPPORT TO FRONT SHOCK ABSORBER NUT

a.
C292272N01
0.823,1.417 1.281,1.417 false 0.542,1.354 1,1.552 0.458,0.198 10 false SST

Secure SST in a vise.

SST
09727-00050  
09727-30021  (09727-00010, 09727-00031)


b.
C275706C01
0.323,0.167 0.719,0.563 0.396,0.396 10 false *a 0.354,2.479 0.677,2.781 0.323,0.302 10 false *b
*a Correct
*b Incorrect


Attach the arms of SST to the diameter of the front coil spring.

CAUTION:
·

Make sure that the front coil spring is installed so that the distance between the upper and lower arms of SST is at the maximum.

·

Make sure that the claws of the arms are securely attached.




c.

Using SST, compress the front coil spring.

CAUTION:
·

If the front coil spring bends during compression, immediately stop compression and reinstall SST.

·

Do not excessively compress the front coil spring so that the coils contact each other.

·

Do not use an impact wrench. It will damage SST.




d.

Confirm that the front coil spring is free and remove the front support to front shock absorber nut.

CAUTION:

Do not remove the front support to front shock absorber nut when the front coil spring is not free.



Hide 48609 10.REMOVE FRONT SUSPENSION SUPPORT SUB-ASSEMBLY

Hide 48619A 11.REMOVE STRUT MOUNTING BEARING

Hide 48157C 12.REMOVE FRONT UPPER COIL SPRING INSULATOR

Hide 48132 13.REMOVE FRONT COIL SPRING

a.

Remove SST from the front coil spring.

NOTICE:

Do not use an impact wrench. It will damage SST.



Hide 48331C 14.REMOVE FRONT SPRING BUMPER

Hide 48158C 15.REMOVE FRONT LOWER COIL SPRING INSULATOR

Hide 48520 16.REMOVE FRONT SHOCK ABSORBER ASSEMBLY