Home › Suspension › FRONT SUSPENSION › FRONT LOWER SUSPENSION ARM(for 1AR-FE)
RM3160E _53 Suspension _019689 FRONT SUSPENSION _0107982 FRONT LOWER SUSPENSION ARM(for 1AR-FE) A

FRONT SUSPENSION  FRONT LOWER SUSPENSION ARM(for 1AR-FE)  INSTALLATION  


PROCEDURE

Hide 48069 1.INSTALL FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH (for LH Side)

a.

Install the front lower arm bushing stopper to the front lower No. 1 suspension arm sub-assembly LH.


b.
C292294N01
0.646,0.615 0.781,0.792 0.135,0.177 10 true 1 1.26,0.354 1.385,0.542 0.125,0.188 10 true 2 2.323,0.969 2.479,1.167 0.156,0.198 10 false 3

Install the front lower No. 1 suspension arm sub-assembly LH to the front frame assembly with the 3 bolts and nut in the order shown in the illustration.

Torque:
Bolt 1, 2 : 200 N*m (2039 kgf*cm, 148 ft.*lbf)
Bolt 3 : 135 N*m (1377 kgf*cm, 100 ft.*lbf)

NOTICE:

Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.



c.

Install the front lower No. 1 suspension arm sub-assembly LH to the front lower ball joint assembly with the bolt and 2 nuts.

Torque:
92 N*m (938 kgf*cm, 68 ft.*lbf)


Hide 12372A 2.INSTALL ENGINE MOUNTING INSULATOR LH (for LH Side)

a.
C292288C01
2.052,1.26 2.469,1.26 true 2.302,1.927 2.719,1.927 false 2.729,1.854 3.042,2.01 0.313,0.156 10 false *a 2.479,1.188 2.677,1.365 0.198,0.177 10 true *b
*a Jack
*b Wooden Block
V100135

Front of the Vehicle
V100155

Wooden Block Placement Location


Using a jack and a wooden block, support the front lower No. 1 suspension arm sub-assembly LH at the position shown in the illustration.


b.

While ensuring that the engine assembly with transaxle does not interfere with surrounding components, jack up the engine assembly with transaxle and front lower No. 1 suspension arm sub-assembly to a position that allows the engine mounting insulator LH to be removed.

CAUTION:

Do not jack up the front lower No. 1 suspension arm sub-assembly LH too high as the vehicle may fall.


NOTICE:
·

Do not position the wooden block under the oil pan.

·

Do not damage the components surrounding the engine assembly with transaxle.

·

Do not damage the front drive shaft assembly.

·

Tilt the engine assembly with transaxle as little as possible.

·

Ensure that the jack and wooden block are stable.

·

Make sure to perform this operation with the vehicle kept as low as possible.



HINT:

Jack up the front lower No. 1 suspension arm sub-assembly LH to prevent damage to the front drive shaft assembly.



c.
C292299C01
1.74,0.688 2.229,0.688 true 2.24,0.604 2.458,0.792 0.219,0.188 10 true *a
*a Pin


Set the engine mounting insulator LH on the front frame assembly.


d.

Slowly lower the engine assembly with transaxle using a jack and a wooden block.

NOTICE:
·

Match the position of the pin (stopper).

·

Do not damage the components surrounding the engine assembly with transaxle.

·

Ensure that the jack and wooden block are stable.




e.

Remove the jack and wooden block that are used to support the front lower No. 1 suspension arm sub-assembly LH.


f.
C292291N01
1.292,0.135 1.438,0.323 0.146,0.188 10 true A 0.573,1.865 0.719,2.052 0.146,0.188 10 true B 2.135,1.25 2.281,1.438 0.146,0.188 10 true B 2.115,1.917 2.26,2.104 0.146,0.188 10 false B

Install the engine mounting insulator LH with the 4 nuts.

Torque:
Nut (A) : 95 N*m (969 kgf*cm, 70 ft.*lbf)
Nut (B) : 99 N*m (1010 kgf*cm, 73 ft.*lbf)


g.

Install the 2 hole plugs.


Hide 48068 3.INSTALL FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH (for RH Side)

a.

Install the front lower arm bushing stopper to the front lower No. 1 suspension arm sub-assembly RH.


b.
C292298N01
2.781,0.708 2.917,0.885 0.135,0.177 10 true 1 2.24,0.448 2.385,0.635 0.146,0.188 10 true 2 0.865,0.906 1.021,1.104 0.156,0.198 10 false 3

Install the front lower No. 1 suspension arm sub-assembly RH to the front frame assembly with the 3 bolts and nut in the order shown in the illustration.

Torque:
Bolt 1, 2 : 200 N*m (2039 kgf*cm, 148 ft.*lbf)
Bolt 3 : 135 N*m (1377 kgf*cm, 100 ft.*lbf)

NOTICE:

Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.



c.

Install the front lower No. 1 suspension arm sub-assembly RH to the front lower ball joint assembly with the bolt and 2 nuts.

Torque:
92 N*m (938 kgf*cm, 68 ft.*lbf)


Hide 12362 4.INSTALL ENGINE MOUNTING INSULATOR RH (for RH Side)

a.
C292289C01
0.938,1.865 1.375,1.865 false 2.552,1.333 2.875,1.333 true 0.781,1.792 1.094,1.948 0.313,0.156 10 false *a 2.906,1.26 3.125,1.438 0.219,0.177 10 true *b
*a Jack
*b Wooden Block
V100135

Front of the Vehicle
V100155

Wooden Block Placement Location


Using a jack and a wooden block, support the front lower No. 1 suspension arm sub-assembly RH at the position shown in the illustration.


b.

While ensuring that the engine assembly with transaxle does not interfere with surrounding components, jack up the engine assembly with transaxle and front lower No. 1 suspension arm sub-assembly RH to a position that allows the engine mounting insulator RH to be removed.

CAUTION:

Do not jack up the front lower No. 1 suspension arm sub-assembly RH too high as the vehicle may fall.


NOTICE:
·

Do not position the wooden block under the oil pan.

·

Do not damage the components surrounding the engine assembly with transaxle.

·

Do not damage the front drive shaft assembly.

·

Tilt the engine assembly with transaxle as little as possible.

·

Ensure that the jack and wooden block are stable.

·

Make sure to perform this operation with the vehicle kept as low as possible.



HINT:

Jack up the front lower No. 1 suspension arm sub-assembly RH to prevent damage to the front drive shaft assembly.



c.
C292302C01
2.448,1.344 2.875,0.927 2.875,0.927 2.469,0.521 false 2.906,0.854 3.219,1.01 0.313,0.156 10 false *a
*a Cutout


Set the engine mounting insulator RH on the front frame assembly.


d.

Slowly lower the engine assembly with transaxle using a jack and a wooden block.

NOTICE:
·

Match the position of the cutout (stopper).

·

Do not damage the components surrounding the engine assembly with transaxle.

·

Ensure that the jack and wooden block are stable.




e.

Remove the jack and wooden block that are used to support the front lower No. 1 suspension arm sub-assembly RH.


f.
C292296N01
2.104,0.26 2.26,0.458 0.156,0.198 10 true A 1.01,1.323 1.167,1.51 0.156,0.188 10 true B 1.063,1.969 1.219,2.167 0.156,0.198 10 false B 2.792,1.854 2.948,2.052 0.156,0.198 10 true B

Install the engine mounting insulator RH with the 4 nuts.

Torque:
Nut (A) : 95 N*m (969 kgf*cm, 70 ft.*lbf)
Nut (B) : 99 N*m (1010 kgf*cm, 73 ft.*lbf)


g.

Install the 2 hole plugs.


Hide 12313 5.INSTALL ENGINE MOVING CONTROL ROD BRACKET

a.
C292305

Temporarily install the engine moving control rod bracket with the 4 bolts.


b.

Fully tighten the 4 bolts.

Torque:
38 N*m (387 kgf*cm, 28 ft.*lbf)


Hide 12327A 6.INSTALL NO. 2 ENGINE MOUNTING STAY RH

Hide 12361 7.INSTALL FRONT ENGINE MOUNTING INSULATOR

a.

Install the front engine mounting insulator to the front frame assembly with the 3 nuts.

Torque:
58 N*m (591 kgf*cm, 43 ft.*lbf)


b.

Install the hole plug.


Hide 53737B 8.INSTALL FRONT FENDER APRON SEAL LH (for LH Side)

Hide 53736 9.INSTALL FRONT FENDER APRON SEAL RH (for RH Side)

Hide 51442 10.INSTALL NO. 2 ENGINE UNDER COVER

Hide 51441 11.INSTALL NO. 1 ENGINE UNDER COVER

Hide 12.INSTALL FRONT WHEELS

Torque:
103 N*m (1050 kgf*cm, 76 ft.*lbf)

Hide 17119A 13.INSTALL AIR CLEANER BRACKET

a.
C292282N01
1.656,1.479 1.813,1.677 0.156,0.198 10 true 1 2.104,1.385 2.26,1.583 0.156,0.198 10 true 2

Install the air cleaner bracket with the 2 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)

NOTICE:

Tighten the 2 nuts in the order shown in the illustration.



Hide 82122 14.INSTALL NO. 2 ENGINE WIRE

a.

Engage the clamp and install the No. 2 engine wire.


Hide 17701 16.INSTALL AIR CLEANER CASE SUB-ASSEMBLY

Hide 17801 17.INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Hide 17705 18.INSTALL AIR CLEANER CAP WITH AIR CLEANER HOSE

Hide 17750A 19.INSTALL INLET AIR CLEANER ASSEMBLY

Hide 53295E 20.INSTALL COOL AIR INTAKE DUCT SEAL

Hide 53299D 21.INSTALL RADIATOR SIDE DEFLECTOR SEAL LH

Hide 53298E 22.INSTALL RADIATOR SIDE SEAL RH

Hide 12601B 23.INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY

Hide 24.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 25.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT