Home › Suspension › FRONT SUSPENSION › FRONT LOWER SUSPENSION ARM(for 1AR-FE)
RM3160E _53 Suspension _019689 FRONT SUSPENSION _0107982 FRONT LOWER SUSPENSION ARM(for 1AR-FE) A

FRONT SUSPENSION  FRONT LOWER SUSPENSION ARM(for 1AR-FE)  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 12601B 3.REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY

Hide 53299D 4.REMOVE RADIATOR SIDE DEFLECTOR SEAL LH

Hide 53298E 5.REMOVE RADIATOR SIDE SEAL RH

Hide 53295E 6.REMOVE COOL AIR INTAKE DUCT SEAL

Hide 17750A 7.REMOVE INLET AIR CLEANER ASSEMBLY

Hide 17705 8.REMOVE AIR CLEANER CAP WITH AIR CLEANER HOSE

Hide 17801 9.REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Hide 17701 10.REMOVE AIR CLEANER CASE SUB-ASSEMBLY

Hide 82122 12.SEPARATE NO. 2 ENGINE WIRE

a.
C292284

Disengage the clamp and separate the No. 2 engine wire.


Hide 17119A 13.REMOVE AIR CLEANER BRACKET

a.
C292282

Remove the 2 bolts and air cleaner bracket.


Hide 14.REMOVE FRONT WHEELS

Hide 51441 15.REMOVE NO. 1 ENGINE UNDER COVER

Hide 51442 16.REMOVE NO. 2 ENGINE UNDER COVER

Hide 53737B 17.REMOVE FRONT FENDER APRON SEAL LH (for LH Side)

Hide 53736 18.REMOVE FRONT FENDER APRON SEAL RH (for RH Side)

Hide 12361 19.SEPARATE FRONT ENGINE MOUNTING INSULATOR

a.
C292285

Remove the hole plug.


b.
C292286

Remove the 3 nuts to separate the front engine mounting insulator from the front frame assembly.


Hide 12327A 20.REMOVE NO. 2 ENGINE MOUNTING STAY RH

Hide 12313 21.REMOVE ENGINE MOVING CONTROL ROD BRACKET

Hide 12372A 22.REMOVE ENGINE MOUNTING INSULATOR LH (for LH Side)

a.
C292287

Remove the 2 hole plugs.


b.
C292291

Remove the 4 nuts from the engine mounting insulator LH.


c.
C292288C01
2.052,1.26 2.469,1.26 true 2.302,1.927 2.719,1.927 false 2.729,1.854 3.042,2.01 0.313,0.156 10 false *a 2.479,1.188 2.677,1.365 0.198,0.177 10 true *b
*a Jack
*b Wooden Block
V100135

Front of the Vehicle
V100155

Wooden Block Placement Location


Using a jack and a wooden block, support the front lower No. 1 suspension arm sub-assembly LH at the position shown in the illustration.


d.
C292290C01
1.635,0.969 1.969,0.969 true 2.177,1.615 2.313,1.708 2.313,1.708 2.563,1.708 true 2.583,1.625 2.76,1.802 0.177,0.177 10 true *a 1.448,0.885 1.635,1.073 0.188,0.188 10 true *b
*a Jack
*b Wooden Block
V100135

Front of the Vehicle
V100155

Wooden Block Placement Location


Using a jack and a wooden block, support the engine assembly with transaxle at the position shown in the illustration.


e.

While ensuring that the engine assembly with transaxle does not interfere with surrounding components, jack up the engine assembly with transaxle and front lower No. 1 suspension arm sub-assembly LH to the position where the engine mounting insulator LH can be removed.

CAUTION:

Do not jack up the front lower No. 1 suspension arm sub-assembly LH too high as the vehicle may fall.


NOTICE:
·

Do not position the wooden block under the oil pan.

·

Do not damage the components surrounding the engine assembly with transaxle.

·

Do not damage the front drive shaft assembly.

·

Tilt the engine assembly with transaxle as little as possible.

·

Ensure that the jack and wooden block are stable.

·

Make sure to perform this operation with the vehicle kept as low as possible.



HINT:

Jack up the front lower No. 1 suspension arm sub-assembly LH to prevent damage to the front drive shaft assembly.



f.

Remove the engine mounting insulator LH from the front frame assembly.


g.

Lower the engine assembly with transaxle to its original position.

NOTICE:
·

Do not damage the components surrounding the engine assembly with transaxle.

·

Ensure that the jack and wooden block are stable.

·

Keep the engine assembly with transaxle supported until installation of the engine mounting insulator LH is complete.




h.

Remove the jack and wooden block that are used to support the front lower No. 1 suspension arm sub-assembly LH.


Hide 48069 23.REMOVE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH (for LH Side)

a.
C292293

Remove the bolt and 2 nuts, and separate the front lower No. 1 suspension arm sub-assembly LH from the front lower ball joint assembly.


b.
C292294

Remove the 3 bolts, nut and front lower No. 1 suspension arm sub-assembly LH from the front frame assembly.

NOTICE:

Because the nut has its own stopper, do not turn the nut. Loosen the bolt with the nut secured.



c.

Remove the front lower arm bushing stopper from the front lower No. 1 suspension arm sub-assembly LH.


Hide 12362 24.REMOVE ENGINE MOUNTING INSULATOR RH (for RH Side)

a.
C292295

Remove the 2 hole plugs.


b.
C292296

Remove the 4 nuts from the engine mounting insulator RH.


c.
C292289C01
0.938,1.865 1.375,1.865 false 2.552,1.333 2.875,1.333 true 0.781,1.792 1.094,1.948 0.313,0.156 10 false *a 2.906,1.26 3.125,1.438 0.219,0.177 10 true *b
*a Jack
*b Wooden Block
V100135

Front of the Vehicle
V100155

Wooden Block Placement Location


Using a jack and a wooden block, support the front lower No. 1 suspension arm sub-assembly RH at the position shown in the illustration.


d.
C292292C01
1.615,1.677 1.771,1.823 1.771,1.823 1.99,1.823 true 1.917,1.042 2.354,1.042 true 2.01,1.74 2.198,1.917 0.188,0.177 10 true *a 2.365,0.958 2.542,1.135 0.177,0.177 10 true *b
*a Jack
*b Wooden Block
V100135

Front of the Vehicle
V100155

Wooden Block Placement Location


Using a jack and a wooden block, support the engine assembly with transaxle at the position shown in the illustration.


e.

While ensuring that the engine assembly with transaxle does not interfere with surrounding components, jack up the engine assembly with transaxle and front lower No. 1 suspension arm sub-assembly RH to the position where the engine mounting insulator RH can be removed.

CAUTION:

Do not jack up the front lower No. 1 suspension arm sub-assembly RH too high as the vehicle may fall.


NOTICE:
·

Do not position the wooden block under the oil pan.

·

Do not damage the components surrounding the engine assembly with transaxle.

·

Do not damage the front drive shaft assembly.

·

Tilt the engine assembly with transaxle as little as possible.

·

Ensure that the jack and wooden block are stable.

·

Make sure to perform this operation with the vehicle kept as low as possible.



HINT:

Jack up the front lower No. 1 suspension arm sub-assembly RH to prevent damage to the front drive shaft assembly.



f.

Remove the engine mounting insulator RH from the front frame assembly.


g.

Lower the engine assembly with transaxle to its original position.

NOTICE:
·

Do not damage the components surrounding the engine assembly with transaxle.

·

Ensure that the jack and wooden block are stable.

·

Keep the engine assembly with transaxle supported until installation of the engine mounting insulator RH is complete.




h.

Remove the jack and the wooden block that are used to support the front lower No. 1 suspension arm sub-assembly RH.


Hide 48068 25.REMOVE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH (for RH Side)

a.
C292297

Remove the bolt and 2 nuts, and separate the front lower No. 1 suspension arm sub-assembly RH from the front lower ball joint assembly.


b.
C292298

Remove the 3 bolts, nut and front lower No. 1 suspension arm sub-assembly RH from the front frame assembly.

NOTICE:

Because the nut has its own stopper, do not turn the nut. Loosen the bolt with the nut secured.



c.

Remove the front lower arm bushing stopper from the front lower No. 1 suspension arm sub-assembly RH.