Home › Engine / Hybrid System › 1AR-FE FUEL › FUEL SYSTEM
RM3160E _51 Engine / Hybrid System _019673 1AR-FE FUEL _0108295 FUEL SYSTEM G

1AR-FE FUEL  FUEL SYSTEM  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.CHECK FUEL PUMP OPERATION AND INSPECT FOR FUEL LEAK

a.

Check fuel pump operation.

i.

Connect the GTS to the DLC3.


ii.

Turn the ignition switch to ON and turn the GTS on.

NOTICE:

Do not start the engine.



iii.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.

Powertrain > Engine and ECT > Active Test
Tester Display
Control the Fuel Pump / Speed
50004 234 230

iv.

Check for pressure in the fuel tube sub-assembly from the fuel line. Check that sounds of fuel flowing from the fuel tank assembly can be heard. If no sound can be heard, check the fuel pump, ECM and wiring connectors.



b.

Inspect for fuel leaks.

i.

Check that there are no fuel leaks from the fuel system after doing any maintenance or repairs. If there is a fuel leak, repair or replace parts as necessary.



c.

Turn the ignition switch off.


d.

Disconnect the GTS from the DLC3.


Hide 2.CHECK FUEL PRESSURE

a.

Discharge the fuel system pressure.

Click hereEngine / Hybrid System>1AR-FE FUEL>FUEL SYSTEM>PRECAUTION


b.

Measure the battery voltage.

Standard Voltage:

11 to 14 V



c.

Disconnect the cable from the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



d.

Remove the No. 1 fuel pipe clamp from the fuel tube connector.


e.

Disconnect the fuel tube sub-assembly from the fuel pipe.

Click hereEngine / Hybrid System>1AR-FE FUEL>FUEL SYSTEM>PRECAUTION


f.
A255967C10
2.813,0.438 2.594,0.229 2.594,0.229 2.458,0.229 false 1.677,1.635 2.083,1.219 2.083,1.219 2.177,1.219 false 0.771,2.365 0.771,2.552 false 1.5,0.802 1.5,1.063 false 0.833,0.521 0.635,0.521 false 1.063,1.031 1.063,1.198 false 1.573,3.344 1.719,3.083 1.719,3.083 1.813,3.083 false 1.302,3.979 1.396,4.073 1.396,4.073 1.51,4.073 false 2.281,3.583 2.281,3.844 false 2.719,3.333 2.719,3.635 false 2.271,0.135 2.635,0.375 0.365,0.24 10 false *c 2.25,1.125 2.604,1.323 0.354,0.198 10 false *d 0.708,2.583 1.052,2.792 0.344,0.208 10 false *1 1,1.219 1.313,1.438 0.313,0.219 10 false *b 0.469,0.427 0.875,0.656 0.406,0.229 10 false *a 1.427,1.094 1.792,1.292 0.365,0.198 10 false *a 2.229,3.885 2.552,4.073 0.323,0.188 10 false *f 1.896,2.99 2.26,3.198 0.365,0.208 10 false *a 1.573,4 1.906,4.198 0.333,0.198 10 false *e 2.667,3.656 2.99,3.844 0.323,0.188 10 false *g
*1 Fuel Tube Sub-assembly (Vehicle Side)
*a SST (Hose Band)
*b SST (T-joint)
*c SST (Gauge)
*d SST (Hose Joint)
*e SST (Hose)
*f SST (Fuel Tube Connector)
*g Fuel Pipe (Vehicle Side)


Install SST (EFI fuel pressure gauge) as shown in the illustration.

SST
09268-45101  (09268-41250, 09268-41260, 09268-41280, 09268-41500, 09268-41700, 95336-08070)


g.

Wipe up any spilled fuel.


h.

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



i.

Connect the GTS to the DLC3.


j.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.

Powertrain > Engine and ECT > Active Test
Tester Display
Control the Fuel Pump / Speed
50004 234 230

k.

Measure the fuel pressure.

Standard Fuel Pressure:

304 to 343 kPa (3.1 to 3.5 kgf/cm2, 44 to 50 psi)


·

If the fuel pressure is greater than the standard, replace the fuel pressure regulator assembly.

·

If the fuel pressure is less than the standard, check the fuel hoses and connections, fuel pump, fuel filter and fuel pressure regulator assembly.



l.

Disconnect the GTS from the DLC3.


m.

Start the engine.


n.

Measure the fuel pressure at idle.

Standard Fuel Pressure:

304 to 343 kPa (3.1 to 3.5 kgf/cm2, 44 to 50 psi)


HINT:

Standard idle speed.

Click hereEngine / Hybrid System>1AR-FE (ENGINE MECHANICAL)>ENGINE>ON-VEHICLE INSPECTION



o.

Stop the engine.


p.

Check that the fuel pressure remains as specified for 5 minutes after the engine stops.

Standard Fuel Pressure:

147 kPa (1.5 kgf/cm2, 21 psi) or more


If the fuel pressure is not as specified, check the fuel pump, fuel pressure regulator assembly and/or fuel injector assemblies.


q.

After checking the fuel pressure, disconnect the cable from the negative (-) battery terminal and carefully remove SST (EFI fuel pressure gauge) to prevent fuel from spraying.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



r.

Reconnect the fuel tube sub-assembly to the fuel pipe.


s.

Install the No. 1 fuel pipe clamp to the fuel tube connector.