Perform "Inspection After Repair" after replacing the fuel pump.
Click hereEngine / Hybrid System>1AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION
1. PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notice before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
2. DISCHARGE FUEL SYSTEM PRESSURE
3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
4.REMOVE REAR NO. 1 SEAT ASSEMBLY
for 60/40 Split Seat Type LH Side: Click hereVehicle Interior>SEAT>REAR NO. 1 SEAT ASSEMBLY(for 60/40 Split Seat Type LH Side)>REMOVAL
for 60/40 Split Seat Type RH Side: Click hereVehicle Interior>SEAT>REAR NO. 1 SEAT ASSEMBLY(for 60/40 Split Seat Type RH Side)>REMOVAL
58410B
5.REMOVE DECK BOARD ASSEMBLY
58409A
6.REMOVE NO. 3 DECK BOARD SUB-ASSEMBLY
64742C
7.REMOVE DECK SIDE TRIM BOX LH
64993
8.REMOVE REAR DECK FLOOR BOX
58387B
9.REMOVE REAR FLOOR FINISH PLATE
64910J
10.REMOVE TONNEAU COVER ASSEMBLY
11.REMOVE REAR NO. 2 SEAT ASSEMBLY
67918A
12.REMOVE REAR DOOR SCUFF PLATE LH
13.REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH
67917A
14.REMOVE REAR DOOR SCUFF PLATE RH
15.REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH
64713F
16.REMOVE FRONT DECK SIDE TRIM COVER LH
73370C
17.DISCONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY LH
64715E
18.REMOVE NO. 2 DECK SIDE TRIM COVER
64735
19.REMOVE DECK TRIM SIDE SERVICE HOLE COVER
73570
20.DISCONNECT REAR NO. 2 SEAT OUTER BELT ASSEMBLY LH
64974
21.REMOVE DECK TRIM POCKET COVER (for LH Side)
64725F
22.REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK (for LH Side)
66311
23.REMOVE ROPE HOOK (for LH Side)
64740C
24.REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH
64712F
25.REMOVE FRONT DECK SIDE TRIM COVER RH
73360C
26.DISCONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY RH
64714H
27.REMOVE NO. 1 DECK SIDE TRIM COVER
73297E
28.REMOVE DECK TRIM SIDE BELT HOLE COVER RH
73560
29.DISCONNECT REAR NO. 2 SEAT OUTER BELT ASSEMBLY RH
62627D
30.REMOVE SIDE TRIM COVER RH (w/o Rear Automatic Air Conditioning System)
88625Q
31.REMOVE COOLER (NO. 2 ROOM TEMP. SENSOR) THERMISTOR
81240
32.REMOVE NO. 1 ROOM LIGHT ASSEMBLY
64974
33.REMOVE DECK TRIM POCKET COVER (for RH Side)
64725F
34.REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK (for RH Side)
66311
35.REMOVE ROPE HOOK (for RH Side)
64730B
36.REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH
58325E
37.REMOVE REAR FLOOR SERVICE HOLE COVER
Turn back the front floor carpet.
Remove the rear floor service hole cover and butyl tape.
Disconnect the fuel pump connector.
77209F
38.DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY
| *1 | Fuel Suction Plate Sub-assembly |
| *2 | Tube Joint Clip |
| *a | Fuel Tube Joint |
| *b | O-ring |
| *c | Nylon Tube |
|
Pull Off |
|
Pull Off |
Remove the tube joint clip, and pull off the fuel tube joint of the fuel tank main tube sub-assembly.
Remove any foreign matter on the fuel tube joint before performing this work.
Do not allow any scratches or foreign matter to get on the parts when disconnecting them as the fuel tube joint has O-rings that seal the fuel pipe.
Only disconnect the fuel tube joint by hand.
Do not forcibly bend, twist or turn the nylon tube.
Protect the disconnected part by covering it with a plastic bag after disconnecting the fuel tube joint.
If the fuel tube joint and fuel suction plate sub-assembly are stuck, push and pull to release them.
77144
39.REMOVE FUEL PUMP GAUGE RETAINER
Before performing these procedures, first cover the connector and fuel tube joints of the fuel suction tube with pump and gauge assembly with vinyl tape and then clean any dirt and foreign matter in order to prevent contamination of the fuel system.
Install SST (fuel pump holding tool assy) to the fuel pump gauge retainer.
Insert SST (claw No. 1) between the service hole and fuel pump gauge retainer as shown in the illustration.
| *a | SST (Claw No. 1) | *b | Wide |
Align the detent of the tank suction tube support and cut out of SST (claw No. 1).
| *a | SST (Claw No. 1) | *b | Detent of Tank Suction Tube Support |
|
Front | - | - |
Insert SST (claw) between the service hole and fuel pump gauge retainer as shown in the illustration.
| *a | SST (Claw No. 1) | *b | SST (Claw) |
Use the same procedure as for SST (claw No. 1), insert SST (claw No. 2) between the service hole and fuel pump gauge retainer, and align it with the second detent of the tank suction tube support.
| *a | SST (Claw No. 1) | *b | SST (Claw No. 2) |
| *c | SST (Bridge) | *d | SST (Bolt) |
| *e | Narrow | *f | Contact |
| *g | Cloth | *h | Detent of Tank Suction Tube Support |
Install SST (bridge) to SST (claw No. 1) and SST (claw No. 2) with the 2 SST (bolt).
Place a piece of cloth or equivalent on the fuel suction tube with pump and gauge assembly and lightly tighten the 2 SST (bolt) of SST (bridge) until they come into contact with the fuel suction tube with pump and gauge assembly.
If a piece of cloth or equivalent is not placed between the fuel suction tube with pump and gauge assembly and the 2 SST (bolt), the fuel suction tube with pump and gauge assembly may be damaged.
Install SST (fuel pump retainer tool assy) to the fuel pump gauge retainer.
Position SST (claw) next to SST (claw No. 1) so that the protrusions of the fuel pump gauge retainer are aligned with the grooves of SST (claw). Use the same procedure as for the previous SST (claw), insert the second SST (claw) between the service hole and fuel pump gauge retainer, and position it next to SST (claw No. 2) so that it is opposite to SST (claw) and the protrusions of the fuel pump gauge retainer are aligned with the grooves of SST (claw).
| *a | SST (Claw No. 1) | *b | SST (Claw No. 2) |
| *c | SST (Claw) | *d | SST (Bridge) |
| *e | Triangle Mark | *f | Protrusion of Fuel Pump Gauge Retainer |
| *g | Groove of SST (Claw) | *h | Correct |
| *i | Incorrect | - | - |
Ensure that SST (claw) does not cover the triangle mark of the fuel pump gauge retainer.
| *a | SST (Claw No. 1) |
| *b | SST (Claw No. 2) |
| *c | SST (Claw) |
| *d | SST (Bridge) |
| *e | SST (Plate) |
| *f | SST (Bolt and Washer Set) |
While ensuring that SST (plate) is centered, install SST (plate) to 2 SST (claw) with the 2 SST (bolt and washer set).
| *a | SST (Fuel Pump Holding Tool Assy) |
| *b | SST (Fuel Pump Retainer Tool Assy) |
Attach 2 breaker bars to SST (fuel pump holding tool assy) and 1 breaker bar to SST (fuel pump retainer tool assy).
| *a | Paint Mark |
Place paint marks on the fuel suction tube with pump and gauge assembly, fuel pump gauge retainer and fuel tank assembly as shown in the illustration.
While holding the 2 breaker bars attached to SST (fuel pump holding tool assy), turn the breaker bar attached to SST (fuel pump retainer tool assy) to loosen the fuel pump gauge retainer. [*1]
| *a | SST (Fuel Pump Holding Tool Assy) | *b | SST (Fuel Pump Retainer Tool Assy) |
| *c | Holding | *d | Turn |
| *e | Press down | - | - |
Press down on the 2 locations shown in the illustration to prevent SST (fuel pump holding tool assy) from turning.
Check that only the paint mark on the fuel pump gauge retainer has moved.
| *a | Paint Mark | *b | Correct |
| *c | Incorrect | - | - |
If the paint mark on the fuel suction tube with pump and gauge assembly has also moved, tighten the fuel pump gauge retainer until the paint marks are aligned at the original position. Then repeat from step [*1].
Loosen the fuel pump gauge retainer by using SST (fuel pump retainer tool assy) until the fuel pump gauge retainer turns approximately 360°.
| *a | SST (Claw) | *b | SST (Fuel Pump Holding Tool Assy) |
| *c | SST (Fuel Pump Retainer Tool Assy) | - | - |
Remove SST (fuel pump retainer tool assy) and SST (fuel pump holding tool assy) from the fuel pump gauge retainer.
Check that the fuel pump gauge retainer can be loosened by hand.
If the fuel pump gauge retainer cannot be loosened by hand, use SST (fuel pump retainer tool assy) to loosen the fuel pump gauge retainer.
| *a | SST (Fuel Pump Retainer Tool Assy) | - | - |
While holding the fuel suction tube with pump and gauge assembly by hand, remove the fuel pump gauge retainer.
77020A
40.REMOVE FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY
Remove the fuel suction tube with pump and gauge assembly from the fuel tank assembly.
Make sure that the fuel sender gauge arm does not bend.
| *1 | Fuel Suction Tube Set Gasket |
Remove the fuel suction tube set gasket from the fuel tank assembly.