Home › Engine / Hybrid System › 1AR-FE FUEL › FUEL SYSTEM
RM3160E _51 Engine / Hybrid System _019673 1AR-FE FUEL _0108295 FUEL SYSTEM L

1AR-FE FUEL  FUEL SYSTEM  PRECAUTION  


IGNITION SWITCH EXPRESSIONS


a.

The type of ignition switch used on this model differs depending on the specifications of the vehicle. The expressions listed in the table below are used in this section.

Expression Ignition Switch (Position) Engine Switch (Condition)
Ignition Switch off LOCK Off (Lock)
Ignition Switch ACC ACC On (ACC)
Ignition Switch ON ON On (IG)
Engine Start START On (Start)



PRECAUTIONS


a.

Before inspecting and repairing the fuel system, disconnect the cable from the negative (-) battery terminal.


b.

Do not smoke or work near fire when handling the fuel system.


c.

Keep fuel away from rubber or leather parts.



DISCHARGE FUEL SYSTEM PRESSURE


CAUTION:
·

Make sure the engine coolant temperature is 60°C (140°F) or less when performing this procedure.

·

Perform the following procedure to prevent fuel from spraying before removing any fuel system parts.

·

Pressure will still remain in the fuel lines even after performing the following procedure. When disconnecting a fuel line, cover it with a piece of cloth to prevent fuel from spraying or coming out.



a.

When discharging fuel system pressure by disconnecting the C/OPN relay:

i.

Remove the engine room relay block and junction block assembly cover.


ii.

Remove the C/OPN relay.


iii.

Start the engine. After the engine has stopped on its own, turn the ignition switch off.

NOTICE:

Do not increase the engine speed or drive the vehicle while waiting for the engine to stop on its own.



iv.

Crank the engine again and make sure that the engine does not start.

HINT:

DTC P0171 (System Too Lean), P1603 (Engine Stall History), P1604 (Startability Malfunction) and P1605 (Rough Idling) may be stored. Clear the DTCs before proceeding to the next step.

Click hereEngine / Hybrid System>1AR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR



v.

Remove the fuel tank cap assembly and discharge the pressure from the fuel tank assembly.


vi.

Disconnect the cable from the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



vii.

Install the C/OPN relay.


viii.

Install the engine room relay block and junction block assembly cover.



b.

When discharging fuel system pressure by disconnecting the fuel pump connector:

i.

Disconnect the fuel pump connector.

Click hereEngine / Hybrid System>1AR-FE FUEL>FUEL PUMP>REMOVAL


ii.

Start the engine. After the engine has stopped on its own, turn the ignition switch off.

NOTICE:

Do not increase the engine speed or drive the vehicle while waiting for the engine to stop on its own.



iii.

Crank the engine again and make sure that the engine does not start.

HINT:

DTC P0171 (System Too Lean), P1603 (Engine Stall History), P1604 (Startability Malfunction) and P1605 (Rough Idling) may be stored. Clear the DTCs before proceeding to the next step.

Click hereEngine / Hybrid System>1AR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR



iv.

Remove the fuel tank cap assembly and discharge the pressure from the fuel tank assembly.


v.

Disconnect the cable from the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



vi.

Connect the fuel pump connector.

Click hereEngine / Hybrid System>1AR-FE FUEL>FUEL PUMP>INSTALLATION




FUEL LINE


a.

When disconnecting a high-pressure fuel line, a large amount of fuel will spray. Perform the following procedure:

i.

Discharge fuel system pressure.


ii.

Disconnect the fuel tube.


iii.

Drain the fuel remaining inside the fuel tube into a container.


iv.

Cover the disconnected fuel pipe and fuel tube connector with plastic bags to prevent damage and contamination.



b.

Metallic Type:

Perform the following procedure when disconnecting a fuel tube connector.

NOTICE:

Remove any dirt or foreign matter on the fuel tube connector and fuel pipe before performing this work.


i.
A315515C01
2.594,1.135 2.688,1.365 2.688,1.365 2.771,1.135 false 2.615,1.396 2.927,1.552 0.313,0.156 10 false *a
*a Claw


Disengage the 2 claws to remove the No. 2 fuel pipe clamp.

NOTICE:

Do not reuse the No. 2 fuel pipe clamp.



ii.
A062165N01
1.979,0.719 2.49,1.635 2.49,1.635 2.021,1.854 true 2.531,1.552 2.844,1.729 0.313,0.177 10 SST

Install SST (fuel hose puller) to the fuel tube connector as shown in the illustration.

SST
09268-21011  


iii.
A284030C16
2.167,1.344 2.448,1.771 2.448,1.771 2.635,1.771 false 0.708,1.24 1.021,1.396 0.313,0.156 10 false *a 2.74,1.688 3.208,1.948 0.469,0.26 10 false SST
*a Retainer (4 places)


Turn SST (fuel hose puller), align the retainers inside the fuel tube connector with the SST (fuel hose puller) chamfers and insert SST (fuel hose puller) into the fuel tube connector.


iv.

Mount the retainer of the fuel tube connector onto the chamfered part of SST (fuel hose puller).


v.
A076220C14
2.26,1.573 2.26,1.875 false 0.594,1.375 0.594,1.708 false 1.396,0.875 1.125,0.438 1.125,0.438 1.594,0.875 false 2.917,1.323 2.917,1.531 false 2.156,0.771 2.281,0.438 2.281,0.438 2.417,0.438 false 0.542,0.448 0.76,0.448 0.76,0.448 1.083,0.917 false 0.948,0.323 1.25,0.563 0.302,0.24 10 false *b 2.479,0.354 2.833,0.563 0.354,0.208 10 false *a 2.844,1.573 3.073,1.771 0.229,0.198 10 false *e 0.51,1.74 0.719,1.969 0.208,0.229 10 false *c 2.177,1.917 2.385,2.115 0.208,0.198 10 false *d 0.354,0.375 0.563,0.604 0.208,0.229 10 false *1
*1 Fuel Tube Sub-assembly
*a Retainer
*b O-ring
*c Nylon Tube
*d Fuel Tube Connector
*e Fuel Pipe


Slide SST (fuel hose puller) and the fuel tube connector together until they make a "click" sound, and then disconnect the fuel tube sub-assembly.

NOTICE:
·

Do not allow any scratches or foreign matter to get on the parts when disconnecting them as the fuel tube connector has O-rings that seal the fuel pipe.

·

Do not forcibly bend, twist or turn the nylon tube.




vi.

Check if there is any foreign matter on the sealing surfaces of the disconnected fuel lines. Clean them if necessary.


vii.

Cover the disconnected fuel pipe and fuel tube connector with plastic bags to prevent damage and contamination.



c.

Metallic Type:

Perform the following procedure when connecting a fuel tube connector.

NOTICE:

Check if there is any damage or foreign matter on the connecting parts of the fuel lines.


i.
A304571C01
1.813,1.229 1.969,1.427 0.156,0.198 10 false .
V100135

Pull


Align the fuel tube connector with the fuel pipe, and push the fuel pipe into the fuel tube connector until the fuel tube connector makes a "click" sound. If it is difficult to push the fuel pipe into the fuel tube connector, apply a small amount of clean engine oil to the tip of the fuel pipe.


ii.

After connecting the fuel lines, check that the fuel pipe and fuel tube connector are securely connected by pulling on them.


iii.

Engage the 2 claws to install a new No. 2 fuel pipe clamp.




d.

Quick Type A:

Perform the following procedure when disconnecting a fuel tube connector.

NOTICE:

Remove any dirt or foreign matter on the fuel tube connector and fuel pipe before performing this work.


i.
A207802

Clamp Type:

Disengage the claw and remove the No. 1 fuel pipe clamp.


ii.
A313757C01
0,0 0,0 false
V100135

Pull Off


Cover Type:

Pull off the fuel tube connector cover.


iii.

Check that there is no dirt or other foreign matter around the fuel tube connector before disconnecting it. Clean the joint if necessary.


iv.
A314711C01
2.385,1.615 2.875,1.99 2.875,1.99 2.646,1.604 false 2.24,3.01 2.375,3.01 2.375,3.01 2.438,3.417 false 2.677,3.5 2.865,3.042 2.865,3.042 2.979,3.042 false 2.375,4.188 2.375,3.979 false 1.667,4.292 2.063,4.292 2.063,4.292 2.063,3.813 false 1.896,4.292 1.896,3.802 false 1,2.979 1.146,2.979 1.146,2.979 1.365,3.458 false 2.927,1.958 3.24,2.115 0.313,0.156 10 false *a 1.5,4.219 1.813,4.375 0.313,0.156 10 false *b 2.302,4.208 2.615,4.365 0.313,0.156 10 false *c 3.021,2.969 3.333,3.125 0.313,0.156 10 false *d 0.833,2.896 1.146,3.052 0.313,0.156 10 false *e 2.083,2.927 2.396,3.083 0.313,0.156 10 false *a
*a Retainer
*b O-ring
*c Fuel Tube Connector
*d Fuel Pipe
*e Nylon Tube
V100135

Pinch
V100136

Pull


Pinch the retainer of the fuel tube connector, and then pull the fuel tube connector off of the fuel pipe.

NOTICE:

Be sure to disconnect the fuel tube connector by hand.



v.

If the fuel tube connector and fuel pipe are stuck, push and pull the fuel tube connector to release it. Pull the fuel tube connector off of the fuel pipe carefully.

NOTICE:
·

Be sure to disconnect the fuel tube connector by hand.

·

Do not allow any scratches or foreign matter to get on the parts when disconnecting them as the fuel tube connector has O-rings that seal the fuel pipe.

·

Do not forcibly bend, twist or turn the nylon tube.




vi.

Check if there is any foreign matter on the sealing surfaces of the disconnected fuel lines. Clean them if necessary.


vii.

Cover the disconnected fuel pipe and fuel tube connector with plastic bags to prevent damage and contamination.



e.

Quick Type A:

Perform the following procedure when connecting a fuel tube connector.

NOTICE:

Check if there is any damage or foreign matter on the connecting parts of the fuel lines.


i.
A303841C01
1.542,1.563 1.698,1.76 0.156,0.198 10 false .
V100135

Pull


Align the fuel tube connector with the fuel pipe, and push them together until the fuel tube connector makes a "click" sound. If it is difficult to push the fuel pipe into the fuel tube connector, apply a small amount of clean engine oil to the tip of the fuel pipe and reinsert it.


ii.

After connecting the fuel lines, check that the fuel pipe and fuel tube connector are securely connected by pulling on them.


iii.

Clamp Type:

Engage the claw and install the No. 1 fuel pipe clamp.


iv.
A313759C01
0,0 0,0 false
V100135

Push In


Cover Type:

Push in the fuel tube connector cover.




f.

Quick Type B:

Perform the following procedure when disconnecting a fuel tube connector.

NOTICE:

Remove any dirt or foreign matter on the fuel tube connector and fuel pipe before performing this work.


i.
A310728C01
0.854,3.063 1.073,3.063 1.073,3.063 1.26,2.854 false 2.052,2.75 2.417,2.75 false 0.688,2.979 1,3.135 0.313,0.156 10 false *a 1.885,2.667 2.198,2.823 0.313,0.156 10 false *a
*a Retainer
V100135

Pull Out
V100136

Pull Off


Pull out the retainer to disengage the lock claws and pull off the fuel tube connector.

NOTICE:

Be sure to disconnect the fuel tube connector by hand.



ii.
A310289C01
1.979,1.729 1.979,1.302 false 1.656,1.74 2.135,1.74 2.135,1.74 2.135,1.313 false 2.875,1.729 2.875,1.531 2.875,1.531 2.583,1.25 false 2.542,0.917 2.708,0.49 2.708,0.49 2.802,0.49 false 2.052,0.427 2.219,0.427 2.219,0.427 2.375,0.844 false 2.833,0.396 3.146,0.552 0.313,0.156 10 false *a 1.49,1.646 1.802,1.802 0.313,0.156 10 false *b 1.896,0.333 2.208,0.49 0.313,0.156 10 false *c 2.792,1.75 3.021,1.906 0.229,0.156 10 false *d
*a Retainer
*b O-ring
*c Fuel Tube Connector
*d Fuel Pipe


If the fuel tube connector and fuel pipe are stuck, push and pull the fuel tube connector to release it. Pull the fuel tube connector off of the fuel pipe carefully.

NOTICE:
·

Be sure to disconnect the fuel tube connector by hand.

·

Do not allow any scratches or foreign matter to get on the parts when disconnecting them as the fuel tube connector has O-rings that seal the fuel pipe.




iii.

Check if there is any foreign matter on the sealing surfaces of the disconnected fuel lines. Clean them if necessary.


iv.

Cover the disconnected fuel pipe and fuel tube connector with plastic bags to prevent damage and contamination.



g.

Quick Type B:

Perform the following procedure when connecting a fuel tube connector.

NOTICE:

Check if there is any damage or foreign matter on the connecting parts of the fuel lines.


i.
A310729C01
0.844,3.094 1.031,3.094 1.031,3.094 1.271,2.844 false 2.021,2.75 2.406,2.75 false 0.677,3 0.99,3.156 0.313,0.156 10 false *a 1.844,2.656 2.156,2.813 0.313,0.156 10 false *a
*a Retainer
V100135

Push
V100136

Push In


Align the fuel tube connector with the fuel pipe, and push them together until the fuel tube connector makes a "click" sound. If it is difficult to push the fuel pipe into the fuel tube connector, apply a small amount of clean engine oil to the tip of the fuel pipe and reinsert it.


ii.

Connect the fuel lines and push in the retainer. Check that the fuel pipe and fuel tube connector are securely connected by pulling on them.




h.
A289951C05
2.333,0.427 2.521,0.427 2.521,0.427 2.823,0.74 false 0.917,1.615 1.104,1.615 1.104,1.615 1.365,1.333 false 1.708,1.281 1.906,1.594 1.906,1.594 2.052,1.594 false 2.156,0.354 2.448,0.594 0.292,0.24 10 false *a 2.115,1.531 2.438,1.792 0.323,0.26 10 false *b 0.708,1.521 1.01,1.781 0.302,0.26 10 false *c
*a Fuel Tube Connector
*b Nylon Tube
*c Ethylene Propylene Diene Monomer (EPDM) Rubber Protector


Observe the following precautions when handling a nylon tube:

NOTICE:
·

Do not twist the fuel tube connector part of the nylon tube or fuel tube connector when connecting it.

·

Do not remove the Ethylene Propylene Diene Monomer (EPDM) rubber protector on the outside of the nylon tube.

·

Do not pinch or kink the nylon tubes to prevent fuel leaks.





FUEL INJECTOR ASSEMBLY


a.
A196011C07
0.135,0.083 3.198,1.573 3.063,1.49 0.135,1.635 3.219,3.24 3.083,1.604 1.344,2.927 1.344,2.615 false 0.865,2.844 0.865,2.427 true 0.865,1.25 0.865,0.833 true 1.354,1.292 1.354,1.021 false 0.792,2.854 1.104,3.01 0.313,0.156 10 false *1 1.271,2.958 1.583,3.115 0.313,0.156 10 false *2 0.229,0.156 0.542,0.313 0.313,0.156 10 false *a 0.198,1.698 0.51,1.854 0.313,0.156 10 false *b 1.281,1.323 1.594,1.479 0.313,0.156 10 false *2 0.781,1.26 1.094,1.417 0.313,0.156 10 false *1
*1 O-ring
*2 Fuel Delivery Pipe
*a Correct
*b Incorrect


Observe the following precautions when removing and installing the fuel injector assemblies:

i.

Do not reuse the O-ring or injector vibration insulator.


ii.

When placing a new O-ring onto the fuel injector assembly, do not damage the O-ring.


iii.

Coat a new O-ring with gasoline or spindle oil before installing it.

NOTICE:

Do not use engine oil, gear oil or brake fluid.




b.
A196012C07
2.323,0.667 2.583,1.083 2.583,1.083 2.75,1.083 true 2.333,0.333 2,0.167 2,0.167 1.833,0.167 true 1.167,1.5 0.583,0.833 0.583,0.833 0.417,0.833 true 1.677,0.073 1.99,0.229 0.313,0.156 10 false *1 2.813,1 3.125,1.156 0.313,0.156 10 false *2 0.25,0.74 0.563,0.896 0.313,0.156 10 false *3
*1 Fuel Delivery Pipe
*2 O-ring
*3 Injector Vibration Insulator


Install the fuel injector assembly into the fuel delivery pipe and cylinder head sub-assembly as shown in the illustration.

NOTICE:

Apply gasoline or spindle oil to the contact surfaces of the fuel delivery pipe and fuel injector assembly before installing it.




FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY


a.
A169369C01
2.219,1.125 2.823,1.125 false 2.896,1.042 3.208,1.198 0.313,0.156 10 false *a
*a Tube


Do not disconnect the tube shown in the illustration when disassembling the fuel suction tube with pump and gauge assembly. Doing so will cause reassembly of the fuel suction tube with pump and gauge assembly to be impossible as the tube is pressed into the fuel suction plate sub-assembly.


b.

When replacing the fuel filter, replace it together with the fuel suction plate sub-assembly.



INSPECT FOR FUEL LEAK


a.

Check that there are no fuel leaks from the fuel system after doing any maintenance or repairs.

Click hereEngine / Hybrid System>1AR-FE FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION