Home › Engine / Hybrid System › 2GR-FE FUEL › FUEL INJECTOR › 2013.12–2016.11
RM3160E _51 Engine / Hybrid System _019664 2GR-FE FUEL _0108302 FUEL INJECTOR A

2GR-FE FUEL  FUEL INJECTOR  INSTALLATION  


PROCEDURE

Hide 23250 1.INSTALL FUEL INJECTOR ASSEMBLY

HINT:

Perform "Inspection After Repair" after replacing a fuel injector assembly.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


a.

Apply a light coat of spindle oil or gasoline to new O-rings, and install them to each fuel injector assembly.


b.
A129476C02
2.128,1.245 2.363,1.429 0.235,0.184 10 *a
*a Turn
V100135

Push


Apply a light coat of gasoline or spindle oil where the fuel delivery pipe sub-assembly contacts each O-ring.


c.

Push and twist each fuel injector assembly to install it into the fuel delivery pipe sub-assembly.


d.

Position each fuel injector assembly connector outward.

NOTICE:
·

Do not damage the fuel injector assembly and O-ring.

·

Do not twist the O-ring.

·

After installing each fuel injector assembly, check that it turns smoothly. If not, replace the O-ring with a new one.




Hide 23807 2.INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY

a.

Install 6 new injector vibration insulators to the intake manifold.


b.

Place the fuel delivery pipe sub-assembly with the 6 fuel injector assemblies in position on the intake manifold.

NOTICE:

Be careful not to drop the fuel injector assemblies when installing the fuel delivery pipe sub-assembly.



c.
A137334

Temporarily install the 5 bolts which are used to hold the fuel delivery pipe sub-assembly to the intake manifold.

NOTICE:

After installing the fuel injector assemblies, check that they turn smoothly. If not, reinstall them with new O-rings.



d.

Tighten the 5 bolts which are used to hold the fuel delivery pipe sub-assembly to the intake manifold.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


e.

Connect the 6 fuel injector assembly connectors.


Hide 23901 3.CONNECT FUEL TUBE SUB-ASSEMBLY

a.
A315514C01
1.865,4.208 2.177,4.208 2.177,4.208 2.177,3.708 false 2.01,4.208 2.01,3.719 false 2.573,4.208 2.573,3.771 false 2.813,3.458 2.906,3.052 2.906,3.052 3.042,3.052 false 2.281,2.698 2.458,2.698 2.458,2.698 2.583,3.26 false 1.188,4.26 1.188,3.771 false 2.49,4.198 2.802,4.354 0.313,0.156 10 false *a 2.083,2.615 2.396,2.771 0.313,0.156 10 false *c 1.698,4.115 2.01,4.271 0.313,0.156 10 false *b 3.104,2.969 3.417,3.125 0.313,0.156 10 false *d 1.104,4.271 1.417,4.427 0.313,0.156 10 false *e
*a Retainer
*b O-ring
*c Fuel Tube Connector
*d Fuel Pipe
*e Nylon Tube
V100135

Push


Connect the fuel tube sub-assembly to the fuel delivery pipe sub-assembly.

NOTICE:

Check if there is any damage or foreign matter on the connecting parts of the fuel lines.


i.

Align the fuel tube connector with the fuel pipe, and push them together until the fuel tube connector makes a "click" sound. If it is difficult to push the fuel pipe into the fuel tube connector, apply a small amount of clean engine oil to the tip of the fuel pipe and reinsert it.


ii.

After connecting the fuel lines, check that the fuel pipe and fuel tube connector are securely connected by pulling on them.



b.

Install the No. 2 fuel pipe clamp to the fuel tube connector.


Hide 23292D 4.INSTALL FUEL HOSE PROTECTOR

a.
A313763C01
0,0 0,0 false
V100135

Bolt
V100136

Nut


Install the fuel hose protector with the 2 bolts and nut.

Torque:
Bolt : 21 N*m (214 kgf*cm, 15 ft.*lbf)
Nut : 10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 17190 5.INSTALL INTAKE AIR SURGE TANK ASSEMBLY

Hide 6.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 8.PERFORM INITIALIZATION

a.

Perform "Inspection After Repair" after replacing a fuel injector assembly.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION