Home › Engine / Hybrid System › 2GR-FE FUEL › FUEL PUMP › 2013.12–2016.11
RM3160E _51 Engine / Hybrid System _019664 2GR-FE FUEL _0108304 FUEL PUMP A

2GR-FE FUEL  FUEL PUMP  REMOVAL  


CAUTION / NOTICE / HINT

HINT:

Perform "Inspection After Repair" after replacing the fuel pump.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2. DISCHARGE FUEL SYSTEM PRESSURE

Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 4.REMOVE REAR NO. 1 SEAT ASSEMBLY

Hide 58410B 5.REMOVE DECK BOARD ASSEMBLY

Hide 58409A 6.REMOVE NO. 3 DECK BOARD SUB-ASSEMBLY

Hide 64742C 7.REMOVE DECK SIDE TRIM BOX LH

Hide 64993 8.REMOVE REAR DECK FLOOR BOX

Hide 58387B 9.REMOVE REAR FLOOR FINISH PLATE

Hide 64910J 10.REMOVE TONNEAU COVER ASSEMBLY

Hide 11.REMOVE REAR NO. 2 SEAT ASSEMBLY

Hide 67918A 12.REMOVE REAR DOOR SCUFF PLATE LH

Hide 13.REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH

Hide 67917A 14.REMOVE REAR DOOR SCUFF PLATE RH

Hide 15.REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH

Hide 64713F 16.REMOVE FRONT DECK SIDE TRIM COVER LH

Hide 73370C 17.DISCONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY LH

Hide 64715E 18.REMOVE NO. 2 DECK SIDE TRIM COVER

Hide 64735 19.REMOVE DECK TRIM SIDE SERVICE HOLE COVER

Hide 73570 20.DISCONNECT REAR NO. 2 SEAT OUTER BELT ASSEMBLY LH

Hide 64974 21.REMOVE DECK TRIM POCKET COVER (for LH Side)

Hide 64725F 22.REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK (for LH Side)

Hide 66311 23.REMOVE ROPE HOOK (for LH Side)

Hide 64740C 24.REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH

Hide 64712F 25.REMOVE FRONT DECK SIDE TRIM COVER RH

Hide 73360C 26.DISCONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY RH

Hide 64714H 27.REMOVE NO. 1 DECK SIDE TRIM COVER

Hide 73297E 28.REMOVE DECK TRIM SIDE BELT HOLE COVER RH

Hide 73560 29.DISCONNECT REAR NO. 2 SEAT OUTER BELT ASSEMBLY RH

Hide 62627D 30.REMOVE SIDE TRIM COVER RH (w/o Rear Automatic Air Conditioning System)

Hide 88625T 31.REMOVE COOLER (NO. 2 ROOM TEMP. SENSOR) THERMISTOR

Hide 81240 32.REMOVE NO. 1 ROOM LIGHT ASSEMBLY

Hide 64974 33.REMOVE DECK TRIM POCKET COVER (for RH Side)

Hide 64725F 34.REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK (for RH Side)

Hide 66311 35.REMOVE ROPE HOOK (for RH Side)

Hide 64730B 36.REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH

Hide 58325E 37.REMOVE REAR FLOOR SERVICE HOLE COVER

a.
A313752

Turn back the front floor carpet.


b.
A313753

Remove the rear floor service hole cover and butyl tape.


c.

Disconnect the fuel pump connector.


Hide 77209F 38.DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.
A314718C01
1.844,1.99 1.844,1.656 false 1,2.531 1.135,2.531 1.135,2.531 1.323,2.979 false 1.604,2.51 1.75,2.51 1.75,2.51 1.906,2.958 false 2.333,3.448 2.76,3.448 false 2.5,3.646 2.635,4.021 2.635,4.021 2.802,4.021 false 1.219,3.792 1.219,3.635 1.219,3.635 1.667,3.635 false 1.021,3.802 1.677,3.802 false 2.865,3.938 3.177,4.094 0.313,0.156 10 false *1 1.76,2.021 2.073,2.177 0.313,0.156 10 false *2 1.427,2.417 1.74,2.573 0.313,0.156 10 false *a 0.823,3.708 1.135,3.865 0.313,0.156 10 false *b 0.833,2.438 1.146,2.594 0.313,0.156 10 false *c 2.813,3.365 3.125,3.521 0.313,0.156 10 false *2
*1 Fuel Suction Plate Sub-assembly
*2 Tube Joint Clip
*a Fuel Tube Joint
*b O-ring
*c Nylon Tube
V100135

Pull Off
V100136

Pull Off


Remove the tube joint clip, and pull off the fuel tube joint of the fuel tank main tube sub-assembly.

NOTICE:
·

Remove any foreign matter on the fuel tube joint before performing this work.

·

Do not allow any scratches or foreign matter to get on the parts when disconnecting them as the fuel tube joint has O-rings that seal the fuel pipe.

·

Only disconnect the fuel tube joint by hand.

·

Do not forcibly bend, twist or turn the nylon tube.

·

Protect the disconnected part by covering it with a plastic bag after disconnecting the fuel tube joint.

·

If the fuel tube joint and fuel suction plate sub-assembly are stuck, push and pull to release them.




Hide 77144 39.REMOVE FUEL PUMP GAUGE RETAINER

NOTICE:

Before performing these procedures, first cover the connector and fuel tube joints of the fuel suction tube with pump and gauge assembly with vinyl tape and then clean any dirt and foreign matter in order to prevent contamination of the fuel system.


a.

Install SST (fuel pump holding tool assy) to the fuel pump gauge retainer.

i.

Insert SST (claw No. 1) between the service hole and fuel pump gauge retainer as shown in the illustration.

A329810C01
2.688,1.198 2.927,1.198 false 2.5,1.104 2.688,1.281 0.188,0.177 10 true *a 3.802,1.229 4.115,1.385 0.313,0.156 10 false *b
*a SST (Claw No. 1) *b Wide


SST
09808-14050  (09882-14050)


ii.

Align the detent of the tank suction tube support and cut out of SST (claw No. 1).

A329809C02
2.094,0.51 2.26,0.51 2.26,0.51 2.573,1.063 true 4.552,1.521 4.979,0.458 4.979,0.458 5.156,0.458 true 3.927,4.854 3.927,4.656 3.927,4.656 4.365,4.385 true 1.917,0.417 2.208,0.615 0.292,0.198 10 false *a 3.854,4.896 4.167,5.052 0.313,0.156 10 false *b 5.208,0.385 5.5,0.583 0.292,0.198 10 false *a
*a SST (Claw No. 1) *b Detent of Tank Suction Tube Support
V100135

Front - -



iii.

Insert SST (claw) between the service hole and fuel pump gauge retainer as shown in the illustration.

A329814C01
0.885,1 1.385,1 false 2.198,1.51 2.198,0.896 true 4.094,1.021 4.479,1.021 true 4.906,1.469 5.177,1.604 5.177,1.604 5.344,1.604 false 0.708,0.917 1.021,1.073 0.313,0.156 10 false *a 2.125,1.563 2.438,1.719 0.313,0.156 10 true *b 5.396,1.531 5.708,1.688 0.313,0.156 10 true *b 3.917,0.938 4.229,1.094 0.313,0.156 10 false *a
*a SST (Claw No. 1) *b SST (Claw)


SST
09808-14040  (09882-14040)


iv.

Use the same procedure as for SST (claw No. 1), insert SST (claw No. 2) between the service hole and fuel pump gauge retainer, and align it with the second detent of the tank suction tube support.

A329811C01
1.25,5.813 1.333,6.313 1.333,6.313 1.5,6.313 false 3.063,1.031 3.417,1.031 false 5.115,5.729 5.417,5.729 false 0.729,1.792 0.906,1.792 0.906,1.792 1.5,2.979 false 0.24,3.385 0.74,3.385 true 4.958,6.479 5.135,6.479 5.135,6.479 5.323,6.177 false 5.25,3.594 5.438,4.208 5.438,4.208 5.667,3.198 true 2.885,0.948 3.198,1.104 0.313,0.156 10 false *b 2.948,1.76 3.26,1.917 0.313,0.156 10 false *e 4.927,5.646 5.24,5.802 0.313,0.156 10 false *f 1.573,6.229 1.833,6.469 0.26,0.24 10 false *h 0.073,3.292 0.385,3.448 0.313,0.156 10 false *a 0.542,1.719 0.854,1.875 0.313,0.156 10 false *c 0.802,3.729 0.979,3.917 0.177,0.188 10 true *d 2.406,2.615 2.583,2.802 0.177,0.188 10 true *d 5.063,2.667 5.24,2.854 0.177,0.188 10 true *d 5.677,2.26 5.854,2.448 0.177,0.188 10 true *d 5.354,4.24 5.615,4.479 0.26,0.24 10 false *g 4.781,6.375 5.042,6.615 0.26,0.24 10 false *g
*a SST (Claw No. 1) *b SST (Claw No. 2)
*c SST (Bridge) *d SST (Bolt)
*e Narrow *f Contact
*g Cloth *h Detent of Tank Suction Tube Support


SST
09808-14050  (09881-14050, 09882-14050, 09883-14050, 09884-14050)


v.

Install SST (bridge) to SST (claw No. 1) and SST (claw No. 2) with the 2 SST (bolt).


vi.

Place a piece of cloth or equivalent on the fuel suction tube with pump and gauge assembly and lightly tighten the 2 SST (bolt) of SST (bridge) until they come into contact with the fuel suction tube with pump and gauge assembly.

NOTICE:

If a piece of cloth or equivalent is not placed between the fuel suction tube with pump and gauge assembly and the 2 SST (bolt), the fuel suction tube with pump and gauge assembly may be damaged.




b.

Install SST (fuel pump retainer tool assy) to the fuel pump gauge retainer.

i.

Position SST (claw) next to SST (claw No. 1) so that the protrusions of the fuel pump gauge retainer are aligned with the grooves of SST (claw). Use the same procedure as for the previous SST (claw), insert the second SST (claw) between the service hole and fuel pump gauge retainer, and position it next to SST (claw No. 2) so that it is opposite to SST (claw) and the protrusions of the fuel pump gauge retainer are aligned with the grooves of SST (claw).

A329812C01
2.198,1.385 2.656,1.385 false 3.135,0.427 3.594,0.427 true 4.208,0.563 5.052,0.563 true 3.5,1.177 4.99,1.177 true 1.844,2.563 1.969,2.563 1.969,2.563 2.208,2.958 false 2.615,2.115 3.031,2.115 3.031,2.115 3.208,2.042 false 2.396,2.865 2.438,3.458 2.438,3.458 3.073,3.115 true 2.406,2.802 3.073,2.531 3.073,2.531 3.115,3.052 true 4.708,2.792 5.573,2.448 5.573,2.448 5.438,2.896 true 4.698,2.844 4.906,3.438 4.906,3.438 5.406,2.948 true 2.01,1.292 2.323,1.448 0.313,0.156 10 false *a 5.115,0.479 5.427,0.635 0.313,0.156 10 false *b 2.948,0.333 3.271,0.5 0.323,0.167 10 false *c 5.063,1.094 5.375,1.25 0.313,0.156 10 false *d 1.677,2.469 1.99,2.625 0.313,0.156 10 false *e 1.167,2.313 1.479,2.469 0.313,0.156 10 false *h 3.74,2.292 3.917,2.479 0.177,0.188 10 false *i 2.438,2.021 2.75,2.177 0.313,0.156 10 false *c 2.333,3.479 2.646,3.635 0.313,0.156 10 false *f 4.833,3.479 5.146,3.635 0.313,0.156 10 false *f 3.094,2.365 3.271,2.552 0.177,0.188 10 false *g 5.604,2.302 5.781,2.49 0.177,0.188 10 false *g
*a SST (Claw No. 1) *b SST (Claw No. 2)
*c SST (Claw) *d SST (Bridge)
*e Triangle Mark *f Protrusion of Fuel Pump Gauge Retainer
*g Groove of SST (Claw) *h Correct
*i Incorrect - -


SST
09808-14040  (09882-14040)

NOTICE:

Ensure that SST (claw) does not cover the triangle mark of the fuel pump gauge retainer.



ii.
A329815C01
0.5,1.448 0.875,1.448 false 1,0.302 1.146,0.302 1.146,0.302 1.521,0.74 false 2.385,0.542 2.833,0.417 2.833,0.417 2.969,0.417 false 1.813,1.156 2.469,1.792 2.469,1.792 2.594,1.792 true 1.635,2.031 1.844,2.104 1.844,2.104 2.167,2.104 false 2.031,0.573 2.406,0.167 2.406,0.167 2.615,0.167 false 0.323,1.365 0.635,1.521 0.313,0.156 10 false *a 3.021,0.344 3.333,0.5 0.313,0.156 10 false *b 2.208,2.021 2.521,2.177 0.313,0.156 10 false *c 2.646,1.719 2.958,1.875 0.313,0.156 10 true *d 0.813,0.219 1.125,0.375 0.313,0.156 10 false *e 2.677,0.073 2.99,0.229 0.313,0.156 10 false *c 1.458,0.042 1.771,0.198 0.313,0.156 10 false *f 1.042,0.781 1.208,0.927 0.167,0.146 10 true *f
*a SST (Claw No. 1)
*b SST (Claw No. 2)
*c SST (Claw)
*d SST (Bridge)
*e SST (Plate)
*f SST (Bolt and Washer Set)


While ensuring that SST (plate) is centered, install SST (plate) to 2 SST (claw) with the 2 SST (bolt and washer set).

SST
09808-14040  (09881-14040, 09883-14040)



c.
A329817C01
2.01,0.646 2.219,0.198 2.219,0.198 2.344,0.198 false 1.958,1.083 2.49,1.521 2.49,1.521 2.604,1.521 true 2.656,1.438 2.969,1.594 0.313,0.156 10 true *a 2.417,0.115 2.729,0.271 0.313,0.156 10 false *b
*a SST (Fuel Pump Holding Tool Assy)
*b SST (Fuel Pump Retainer Tool Assy)


Attach 2 breaker bars to SST (fuel pump holding tool assy) and 1 breaker bar to SST (fuel pump retainer tool assy).


d.
A329818C01
1.333,0.458 0.865,0.458 0.865,0.458 0.865,0.656 false 1.396,0.552 0.865,0.552 false 1.448,0.656 0.635,0.656 false 0.448,0.563 0.76,0.719 0.313,0.156 10 false *a
*a Paint Mark


Place paint marks on the fuel suction tube with pump and gauge assembly, fuel pump gauge retainer and fuel tank assembly as shown in the illustration.


e.

While holding the 2 breaker bars attached to SST (fuel pump holding tool assy), turn the breaker bar attached to SST (fuel pump retainer tool assy) to loosen the fuel pump gauge retainer. [*1]

A331591C01
0.646,1.292 0.802,1.292 0.802,1.292 0.927,1.417 false 2.604,0.156 2.74,0.156 2.74,0.156 2.854,0.229 false 1.969,0.146 2.125,0.146 2.125,0.146 2.125,0.521 false 2.052,0.906 2.219,1.417 2.219,1.417 2.479,1.417 true 0.49,1.208 0.802,1.365 0.313,0.156 10 false *c 4.344,0.792 4.656,0.948 0.313,0.156 10 false *d 2.427,0.073 2.74,0.229 0.313,0.156 10 false *c 1.802,0.063 2.115,0.219 0.313,0.156 10 false *b 2.521,1.344 2.833,1.5 0.313,0.156 10 true *a 1.635,0.458 1.792,0.625 0.156,0.167 10 true *e 2.188,0.125 2.344,0.292 0.156,0.167 10 true *e
*a SST (Fuel Pump Holding Tool Assy) *b SST (Fuel Pump Retainer Tool Assy)
*c Holding *d Turn
*e Press down - -


NOTICE:

Press down on the 2 locations shown in the illustration to prevent SST (fuel pump holding tool assy) from turning.



f.

Check that only the paint mark on the fuel pump gauge retainer has moved.

A331592C01
1.615,0.396 0.854,0.396 false 1.729,0.552 1.104,1 1.104,1 0.969,1 false 1.563,0.552 1.021,0.552 1.021,0.552 1.021,0.396 false 4.865,0.385 4.25,0.385 false 4.792,0.552 4.375,0.552 false 4.875,0.635 4.375,0.635 4.375,0.635 4.375,0.385 false 0.688,0.313 1,0.469 0.313,0.156 10 false *a 0.521,0.042 0.833,0.198 0.313,0.156 10 false *b 3.708,0.021 4.021,0.177 0.313,0.156 10 false *c 4.073,0.302 4.385,0.458 0.313,0.156 10 false *a 0.802,0.917 1.115,1.073 0.313,0.156 10 false *a
*a Paint Mark *b Correct
*c Incorrect - -


HINT:

If the paint mark on the fuel suction tube with pump and gauge assembly has also moved, tighten the fuel pump gauge retainer until the paint marks are aligned at the original position. Then repeat from step [*1].



g.

Loosen the fuel pump gauge retainer by using SST (fuel pump retainer tool assy) until the fuel pump gauge retainer turns approximately 360°.

A331593C01
0.323,1 0.927,1 false 0.917,0.208 1.083,0.208 1.083,0.208 1.563,1.031 false 2.344,0.958 2.958,0.958 false 2.927,4.021 3.083,4.021 3.083,4.021 3.438,4.271 true 0.146,0.906 0.458,1.063 0.313,0.156 10 false *a 0.729,0.115 1.042,0.271 0.313,0.156 10 false *b 2.74,3.938 2.958,4.104 0.219,0.167 10 true *c 3.031,0.875 3.344,1.031 0.313,0.156 10 false *a
*a SST (Claw) *b SST (Fuel Pump Holding Tool Assy)
*c SST (Fuel Pump Retainer Tool Assy) - -



h.

Remove SST (fuel pump retainer tool assy) and SST (fuel pump holding tool assy) from the fuel pump gauge retainer.


i.

Check that the fuel pump gauge retainer can be loosened by hand.

HINT:

If the fuel pump gauge retainer cannot be loosened by hand, use SST (fuel pump retainer tool assy) to loosen the fuel pump gauge retainer.

A331594C01
1.896,0.521 2.083,0.219 2.083,0.219 2.198,0.219 false 2.26,0.135 2.573,0.292 0.313,0.156 10 true *a
*a SST (Fuel Pump Retainer Tool Assy) - -



SST
09808-14040  (09881-14040, 09882-14040, 09883-14040)


j.

While holding the fuel suction tube with pump and gauge assembly by hand, remove the fuel pump gauge retainer.


Hide 77020A 40.REMOVE FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

a.

Remove the fuel suction tube with pump and gauge assembly from the fuel tank assembly.

NOTICE:

Make sure that the fuel sender gauge arm does not bend.



b.
A313779C01
2.083,0.188 2.219,0.188 2.219,0.188 2.333,0.354 false 1.906,0.125 2.219,0.281 0.313,0.156 10 false *1
*1 Fuel Suction Tube Set Gasket


Remove the fuel suction tube set gasket from the fuel tank assembly.