Home › Brake › BRAKE (REAR) › REAR BRAKE
RM3160E _54 Brake _019695 BRAKE (REAR) _0109277 REAR BRAKE A

BRAKE (REAR)  REAR BRAKE  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the LH side and RH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 42431 1.INSTALL REAR DISC

a.
C291548C01
1.979,0.99 2.854,0.896 2.854,0.896 1.99,1.021 true 2.885,0.813 3.188,1.031 0.302,0.219 10 false *a
*a Matchmark


Align the matchmarks of the rear disc and rear axle hub and bearing assembly, and install the rear disc.


Hide 42491 2.INSTALL PARKING BRAKE SHOE ADJUSTING HOLE PLUG

a.

Install the parking brake shoe adjusting hole plug to rear disc.


Hide 47722A 3.INSTALL REAR DISC BRAKE CYLINDER MOUNTING

a.

Install the rear disc brake cylinder mounting to the rear axle carrier sub-assembly with the 2 bolts.

Torque:
95 N*m (969 kgf*cm, 70 ft.*lbf)


Hide 4.INSTALL REAR DISC BRAKE BUSHING DUST BOOT

a.
C211756C01
1.865,1.406 1.854,1.406 false
V100155

Lithium Soap Base Glycol Grease


Apply a light layer of lithium soap base glycol grease to the entire circumference of 2 new rear disc brake bushing dust boots.

HINT:

Apply more than 0.3 g (0.01 oz) of lithium soap base glycol grease to each rear disc brake bushing dust boot.



b.

Install the 2 rear disc brake bushing dust boots to the rear disc brake cylinder mounting.


Hide 47814 5.INSTALL REAR NO. 1 DISC BRAKE CYLINDER SLIDE PIN

a.
C291532C02
0,0 0,0 false
V100155

Lithium Soap Base Glycol Grease


Apply a light layer of lithium soap base glycol grease to the sliding part and the sealing surfaces of the rear No. 1 disc brake cylinder slide pin.


b.

Install the rear No. 1 disc brake cylinder slide pin to the rear disc brake cylinder mounting.


c.

Push the rear No. 1 disc brake cylinder slide pin into the rear disc brake bushing dust boot to engage the pin to the boot.


Hide 47815 6.INSTALL REAR NO. 2 DISC BRAKE CYLINDER SLIDE PIN

a.
C291569C01
0,0 0,0 false
V100155

Lithium Soap Base Glycol Grease


Apply a light layer of lithium soap base glycol grease to the contact surface of the rear No. 2 disc brake cylinder slide pin.


b.

Install a new rear disc brake cylinder slide bushing to the rear No. 2 disc brake cylinder slide pin.


c.
C291534C01
0,0 0,0 false
V100155

Lithium Soap Base Glycol Grease


Apply a light layer of lithium soap base glycol grease to the sliding part and the sealing surfaces of the rear No. 2 disc brake cylinder slide pin.


d.

Install the rear No. 2 disc brake cylinder slide pin to the rear disc brake cylinder mounting.


e.

Push the rear No. 2 disc brake cylinder slide pin into the rear disc brake bushing dust boot to engage the pin to the boot.


Hide 7.INSTALL REAR DISC BRAKE PAD SUPPORT PLATE

a.

Install the 4 rear disc brake pad support plates to the rear disc brake cylinder mounting.

NOTICE:

Be sure to install each rear disc brake pad support plate in the correct position and direction.



Hide 04946 8.INSTALL REAR DISC BRAKE ANTI-SQUEAL SHIM KIT

NOTICE:
·

When replacing worn rear disc brake pads, the rear disc brake anti-squeal shim kit must be replaced together with the rear disc brake pads.

·

Make sure that disc brake grease is not applied onto the lining surface.

·

Install each rear disc brake pad wear indicator plate in the correct position and direction.

·

Install the rear disc brake anti-squeal shims in the correct positions and directions.



a.
C266023C01
0,0 0,0 false
V100144

Disc Brake Grease


Apply disc brake grease to the inside of each rear disc brake anti-squeal shim as shown in the illustration.


b.
C264008C01
0.354,0.99 0.646,0.615 0.646,0.615 0.896,0.615 false 2.438,0.771 2.802,0.771 2.802,0.771 2.948,1.323 false 1.115,2.771 1.479,2.771 1.479,2.771 1.688,2.438 false 2.052,2.958 2.417,2.958 2.417,2.958 2.625,2.625 false 2.281,0.698 2.594,0.854 0.313,0.156 10 false *1 0.958,2.688 1.271,2.844 0.313,0.156 10 false *2 0.938,0.542 1.25,0.698 0.313,0.156 10 false *1 1.896,2.885 2.208,3.042 0.313,0.156 10 false *2
*1 Rear Disc Brake Anti-squeal Shim
*2 Rear Disc Brake Pad Wear Indicator Plate


Install the rear disc brake anti-squeal shim to each rear disc brake pad.


c.

Install the rear disc brake pad wear indicator plate to each rear disc brake pad.


Hide 04466 9.INSTALL REAR DISC BRAKE PAD

a.

Install the 2 rear disc brake pads to the rear disc brake cylinder mounting.

NOTICE:

There should be no oil or grease on the friction surfaces of the rear disc brake pads or the rear disc.



Hide 47850 10.INSTALL REAR DISC BRAKE CYLINDER ASSEMBLY

a.

Hold the 2 rear disc brake cylinder slide pins and install the rear disc brake cylinder assembly to the rear disc brake cylinder mounting with the 2 bolts.

Torque:
26.5 N*m (270 kgf*cm, 20 ft.*lbf)


Hide 47319F 11.CONNECT REAR FLEXIBLE HOSE

a.

Connect the rear flexible hose to the rear disc brake cylinder assembly with a new union bolt and a new gasket.

Torque:
22 N*m (224 kgf*cm, 16 ft.*lbf)

NOTICE:

Install the rear flexible hose lock securely into the lock hole in the rear disc brake cylinder assembly.



Hide 13.ADJUST PARKING BRAKE

Hide 14.INSTALL REAR WHEEL

Torque:
103 N*m (1050 kgf*cm, 76 ft.*lbf)