Home › Vehicle Exterior › DOOR / HATCH › POWER BACK DOOR SYSTEM
RM3160E _59 Vehicle Exterior _019719 DOOR / HATCH _0109291 POWER BACK DOOR SYSTEM C

DOOR / HATCH  POWER BACK DOOR SYSTEM  B2226  PBD Unit Pulse Sensor LH Circuit  


DESCRIPTION

This DTC is stored when the multiplex network door ECU detects an error in the power back door unit assembly set LH pulse signal.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2226 PBD Unit Pulse Sensor LH Circuit The multiplex network door ECU detects an error in the power back door unit assembly set LH pulse signal.
·

Multiplex network door ECU

·

Power back door unit assembly set LH

·

Wire harness or connector



WIRING DIAGRAM

B341467E03
1.104,2.667 1.563,2.865 0.458,0.198 10 false X6 1.104,2.833 5.083,3.031 3.979,0.198 10 false Multiplex Network Door ECU 4.5,2.698 4.958,2.896 0.458,0.198 10 false X1 4.5,2.885 5.917,3.25 1.417,0.365 10 false Power Back Door Unit Assembly Set LH 2.292,2.167 2.75,2.365 0.458,0.198 10 false DS1 2.292,1.667 2.75,1.865 0.458,0.198 10 false DSV 2.292,1.167 2.75,1.365 0.458,0.198 10 false DSG 4.583,1.135 5.042,1.333 0.458,0.198 10 false DSG 2.292,0.635 2.75,0.833 0.458,0.198 10 false DS2 4.583,0.635 5.042,0.833 0.458,0.198 10 false DS2 4.583,1.667 5.042,1.865 0.458,0.198 10 false DSV 4.583,2.167 5.042,2.365 0.458,0.198 10 false DS1 2.667,0.5 3.125,0.698 0.458,0.198 10 false 22 2.667,1 3.125,1.198 0.458,0.198 10 false 11 2.667,1.552 3.125,1.75 0.458,0.198 10 false 12 2.667,2.083 3.125,2.281 0.458,0.198 10 false 23 4.333,0.5 4.792,0.698 0.458,0.198 10 false 6 4.333,1 4.792,1.198 0.458,0.198 10 false 4 4.333,1.552 4.792,1.75 0.458,0.198 10 false 3 4.333,2.083 4.792,2.281 0.458,0.198 10 false 5

PROCEDURE

1.CHECK FOR DTC
a.

Clear the DTCs.

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>DTC CHECK / CLEAR

Body Electrical > Back Door > Clear DTCs
50002 159

b.

Check for DTCs.

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>DTC CHECK / CLEAR

Body Electrical > Back Door > Trouble Codes
50001 159

Result:
Result Proceed to
DTC B2226 is not output A
DTC B2226 is output B



A

B

2.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK DOOR ECU - POWER BACK DOOR UNIT ASSEMBLY SET LH)
2.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK DOOR ECU - POWER BACK DOOR UNIT ASSEMBLY SET LH)
a.

Disconnect the X6 multiplex network door ECU connector.


b.

Disconnect the X1 power back door unit assembly set LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
X6-11 (DSG) - X1-4 (DSG) Always Below 1 Ω
X6-12 (DSV) - X1-3 (DSV) Always Below 1 Ω
X6-22 (DS2) - X1-6 (DS2) Always Below 1 Ω
X6-23 (DS1) - X1-5 (DS1) Always Below 1 Ω
X6-11 (DSG) or X1-4 (DSG) - Body ground Always 10 kΩ or higher
X6-12 (DSV) or X1-3 (DSV) - Body ground Always 10 kΩ or higher
X6-22 (DS2) or X1-6 (DS2) - Body ground Always 10 kΩ or higher
X6-23 (DS1) or X1-5 (DS1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK MULTIPLEX NETWORK DOOR ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK MULTIPLEX NETWORK DOOR ECU
a.
E356834C30
0.146,1.01 0.521,1.281 0.375,0.271 1.927,1.135 2.229,0.74 2.229,0.74 2.375,0.74 true 1.896,1.458 2.094,1.781 2.094,1.781 2.26,1.781 true 1.063,0.708 1.219,0.708 1.219,0.708 1.635,1.208 true 1.26,1.813 1.438,1.813 1.438,1.813 1.688,1.427 true 0.135,0.083 0.594,0.281 0.458,0.198 10 false *a 0.271,1.073 0.729,1.271 0.458,0.198 10 false X1 0.75,0.625 1.208,0.823 0.458,0.198 10 false DSG 2.344,1.698 2.802,1.896 0.458,0.198 10 false DS1 0.958,1.729 1.417,1.927 0.458,0.198 10 false DS2 2.458,0.667 2.917,0.865 0.458,0.198 10 false DSV
*a Front view of wire harness connector
(to Power Back Door Unit Assembly Set LH)


Disconnect the power back door unit assembly set LH connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
X1-4 (DSG) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
X1-5 (DS1) - Body ground Always 7 V or higher
X1-6 (DS2) - Body ground Always 7 V or higher
X1-3 (DSV) - Body ground Always 7 V or higher



Result:
Proceed to
OK
NG



OK

4.CHECK POWER BACK DOOR UNIT ASSEMBLY SET LH

NG

REPLACE MULTIPLEX NETWORK DOOR ECU

4.CHECK POWER BACK DOOR UNIT ASSEMBLY SET LH
a.

Using an oscilloscope, check the waveform of each terminal from the rear of the multiplex network door ECU X6 connector.

E365366C20
0.823,0.635 1.24,0.865 0.417,0.229 1.083,2.615 0.958,2.615 0.958,2.615 0.677,1.656 true 1.208,2.396 1.063,2.396 1.063,2.396 0.75,1.656 true 0.073,0.104 0.385,0.26 0.313,0.156 10 false *a 2.115,0.583 2.427,0.74 0.313,0.156 10 false *b 4.688,0.573 5,0.729 0.313,0.156 10 false *c 4.26,2.063 4.719,2.26 0.458,0.198 10 false GND 6.823,2.063 7.146,2.271 0.323,0.208 10 false GND 1.125,2.542 1.583,2.74 0.458,0.198 10 false DS1 1.281,2.313 1.74,2.51 0.458,0.198 10 false DS2 0.958,0.677 1.417,0.875 0.458,0.198 10 false X6
*a Component with harness connected
(Multiplex Network Door ECU)
*b Waveform (CH1)
*c Waveform (CH2) - -


Measurement Condition:
Item Condition
Tester connection
·

CH1 : X6-23 (DS1) - Body ground

·

CH2 : X6-22 (DS2) - Body ground


Tool setting 2 V/DIV., 2 ms./DIV.
Vehicle condition Open and close the back door by hand.


HINT:

The period changes in accordance to the speed at which the back door is opened and closed by hand.


OK:

The waveform displayed is as shown in the illustration.



Result:
Proceed to
OK
NG



OK

REPLACE MULTIPLEX NETWORK DOOR ECU

NG

REPLACE POWER BACK DOOR UNIT ASSEMBLY SET LH