Home › Vehicle Exterior › DOOR / HATCH › POWER BACK DOOR SYSTEM
RM3160E _59 Vehicle Exterior _019719 DOOR / HATCH _0109291 POWER BACK DOOR SYSTEM C

DOOR / HATCH  POWER BACK DOOR SYSTEM  B2227  PBD Unit Pulse Sensor RH Circuit  


DESCRIPTION

This DTC is stored when the multiplex network door ECU detects an error in the power back door unit assembly set RH pulse signal.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2227 PBD Unit Pulse Sensor RH Circuit The multiplex network door ECU detects an error in the power back door unit assembly set RH pulse signal.
·

Multiplex network door ECU

·

Power back door unit assembly set RH

·

Wire harness or connector



WIRING DIAGRAM

B341467E04
1.104,2.667 1.563,2.865 0.458,0.198 10 false X6 1.104,2.833 5.083,3.031 3.979,0.198 10 false Multiplex Network Door ECU 4.5,2.688 4.958,2.885 0.458,0.198 10 false X25 4.5,2.885 5.917,3.25 1.417,0.365 10 false Power Back Door Unit Assembly Set RH 2.208,2.167 2.667,2.365 0.458,0.198 10 false DSG2 2.208,1.667 2.667,1.865 0.458,0.198 10 false DS22 2.208,1.146 2.667,1.344 0.458,0.198 10 false DS12 4.583,1.135 5.042,1.333 0.458,0.198 10 false DS12 2.208,0.635 2.667,0.833 0.458,0.198 10 false DSV2 4.583,0.635 5.042,0.833 0.458,0.198 10 false DSV2 4.583,1.667 5.042,1.865 0.458,0.198 10 false DS22 4.583,2.167 5.042,2.365 0.458,0.198 10 false DSG2 2.667,0.5 3.125,0.698 0.458,0.198 10 false 3 2.667,1 3.125,1.198 0.458,0.198 10 false 26 2.667,1.552 3.125,1.75 0.458,0.198 10 false 25 2.667,2.083 3.125,2.281 0.458,0.198 10 false 2 4.333,0.5 4.792,0.698 0.458,0.198 10 false 3 4.333,1 4.792,1.198 0.458,0.198 10 false 5 4.333,1.552 4.792,1.75 0.458,0.198 10 false 6 4.333,2.083 4.792,2.281 0.458,0.198 10 false 4

PROCEDURE

1.CHECK FOR DTC
a.

Clear the DTCs.

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>DTC CHECK / CLEAR

Body Electrical > Back Door > Clear DTCs
50002 159

b.

Check for DTCs.

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>DTC CHECK / CLEAR

Body Electrical > Back Door > Trouble Codes
50001 159

Result:
Result Proceed to
DTC B2227 is not output A
DTC B2227 is output B



A

B

2.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK DOOR ECU - POWER BACK DOOR UNIT ASSEMBLY SET RH)
2.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK DOOR ECU - POWER BACK DOOR UNIT ASSEMBLY SET RH)
a.

Disconnect the X6 multiplex network door ECU connector.


b.

Disconnect the X25 power back door unit assembly set RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
X6-2 (DSG2) - X25-4 (DSG2) Always Below 1 Ω
X6-3 (DSV2) - X25-3 (DSV2) Always Below 1 Ω
X6-25 (DS22) - X25-6 (DS22) Always Below 1 Ω
X6-26 (DS12) - X25-5 (DS12) Always Below 1 Ω
X6-2 (DSG2) or X25-4 (DSG2) - Body ground Always 10 kΩ or higher
X6-3 (DSV2) or X25-3 (DSV2) - Body ground Always 10 kΩ or higher
X6-25 (DS22) or X25-6 (DS22) - Body ground Always 10 kΩ or higher
X6-26 (DS12) or X25-5 (DS12) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK MULTIPLEX NETWORK DOOR ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK MULTIPLEX NETWORK DOOR ECU
a.
E356834C31
0.146,1.01 0.5,1.281 0.354,0.271 1.927,1.135 2.229,0.74 2.229,0.74 2.375,0.74 true 1.896,1.458 2.094,1.781 2.094,1.781 2.26,1.781 true 1.063,0.708 1.219,0.708 1.219,0.708 1.635,1.208 true 1.26,1.813 1.438,1.813 1.438,1.813 1.688,1.427 true 0.135,0.083 0.594,0.281 0.458,0.198 10 false *a 0.208,1.063 0.667,1.26 0.458,0.198 10 false X25 0.656,0.625 1.115,0.823 0.458,0.198 10 false DSG2 2.313,1.698 2.771,1.896 0.458,0.198 10 false DS12 0.896,1.74 1.354,1.938 0.458,0.198 10 false DS22 2.406,0.667 2.865,0.865 0.458,0.198 10 false DSV2
*a Front view of wire harness connector
(to Power Back Door Unit Assembly Set RH)


Disconnect the power back door unit assembly set RH connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
X25-4 (DSG2) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
X25-5 (DS12) - Body ground Always 7 V or higher
X25-6 (DS22) - Body ground Always 7 V or higher
X25-3 (DSV2) - Body ground Always 7 V or higher



Result:
Proceed to
OK
NG



OK

4.CHECK POWER BACK DOOR UNIT ASSEMBLY SET RH

NG

REPLACE MULTIPLEX NETWORK DOOR ECU

4.CHECK POWER BACK DOOR UNIT ASSEMBLY SET RH
a.

Using an oscilloscope, check the waveform of each terminal from the rear of the multiplex network door ECU X6 connector.

E365366C21
0.833,0.604 1.188,0.823 0.354,0.219 0.833,2.635 0.708,2.635 0.708,2.635 0.427,1.677 true 0.979,2.406 0.833,2.406 0.833,2.406 0.521,1.667 true 0.073,0.104 0.385,0.26 0.313,0.156 10 false *a 2.115,0.583 2.427,0.74 0.313,0.156 10 false *b 4.688,0.573 5,0.729 0.313,0.156 10 false *c 4.26,2.063 4.719,2.26 0.458,0.198 10 false GND 6.823,2.063 7.146,2.271 0.323,0.208 10 false GND 0.875,2.552 1.333,2.75 0.458,0.198 10 false DS12 1.021,2.323 1.479,2.521 0.458,0.198 10 false DS22 0.938,0.635 1.396,0.833 0.458,0.198 10 false X6
*a Component with harness connected
(Multiplex Network Door ECU)
*b Waveform (CH1)
*c Waveform (CH2) - -


Measurement Condition:
Item Condition
Tester connection
·

CH1 : X6-26 (DS12) - Body ground

·

CH2 : X6-25 (DS22) - Body ground


Tool setting 2 V/DIV., 2 ms./DIV.
Vehicle condition Open and close the back door by hand.


HINT:

The period changes in accordance to the speed at which the back door is opened and closed by hand.


OK:

The waveform displayed is as shown in the illustration.



Result:
Proceed to
OK
NG



OK

REPLACE MULTIPLEX NETWORK DOOR ECU

NG

REPLACE POWER BACK DOOR UNIT ASSEMBLY SET RH