Home › Vehicle Exterior › DOOR / HATCH › POWER BACK DOOR SYSTEM
RM3160E _59 Vehicle Exterior _019719 DOOR / HATCH _0109291 POWER BACK DOOR SYSTEM J

DOOR / HATCH  POWER BACK DOOR SYSTEM  Power Back Door cannot be Operated Using Any Switch  


DESCRIPTION

If the power back door system cannot be operated using any switch, one of the following may be the cause: 1) the multiplex network door ECU has not been initialized, 2) malfunction in the power back door sensor assembly circuit, 3) malfunction in the door control switch circuit, 4) back door closer system malfunction, 5) meter/gauge system malfunction, 6) malfunction in the multiplex network door ECU power source circuit or 7) multiplex network door ECU malfunction.

WIRING DIAGRAM

B361474
0.917,0.333 1.073,0.531 0.156,0.198 10 false 2 2.458,3.969 2.615,4.167 0.156,0.198 10 false 2 0.917,1.667 1.073,1.865 0.156,0.198 10 false 2 4.333,1.542 4.49,1.74 0.156,0.198 10 false 1 2.458,1.667 2.615,1.865 0.156,0.198 10 false 1 2.458,0.313 2.615,0.51 0.156,0.198 10 false 1 0.917,3.979 1.073,4.177 0.156,0.198 10 false 1 2.896,2.729 3.094,2.927 0.198,0.198 10 false 17 2.896,1.583 3.094,1.781 0.198,0.198 10 false 16 2.885,0.24 3.083,0.438 0.198,0.198 10 false 18 2.896,3.885 3.094,4.083 0.198,0.198 10 false 20 4.354,0.771 4.51,0.969 0.156,0.198 10 false 7 4.344,0.26 4.5,0.458 0.156,0.198 10 false 8 4.354,3.438 4.51,3.635 0.156,0.198 10 false 7 2.906,1.781 3.25,1.99 0.344,0.208 10 false X6 2.906,2.927 3.25,3.135 0.344,0.208 10 false X6 2.896,0.427 3.24,0.635 0.344,0.208 10 false X6 2.906,4.083 3.25,4.292 0.344,0.208 10 false X6 4.323,0.958 4.667,1.167 0.344,0.208 10 false X6 4.323,1.729 4.667,1.938 0.344,0.208 10 false X6 4.323,0.448 4.667,0.656 0.344,0.208 10 false X7 4.323,3.635 4.667,3.844 0.344,0.208 10 false X7 1.115,0.333 1.552,0.5 0.438,0.167 10 false OSLE 2.094,0.323 2.427,0.49 0.333,0.167 10 false OSL 1.104,1.677 1.542,1.844 0.438,0.167 10 false OSRE 2.063,1.688 2.438,1.885 0.375,0.198 10 false OSR 0.427,2.208 0.729,2.417 0.302,0.208 10 false X24 2.021,3.979 2.427,4.167 0.406,0.188 10 false MSW 0.49,0.802 0.792,1.01 0.302,0.208 10 false X2 0.5,0.958 3.031,1.156 2.531,0.198 10 false Power Back Door Sensor Assembly LH 0.427,2.375 2.958,2.573 2.531,0.198 10 false Power Back Door Sensor Assembly RH 1.104,3.99 1.479,4.208 0.375,0.219 10 false MSE 1.073,4.438 1.448,4.656 0.375,0.219 10 false F52 1.073,4.594 2.406,4.844 1.333,0.25 10 false Door Control Switch 0.719,5.281 2.531,5.542 1.813,0.26 10 false : CAN Communication Line 2.865,4.938 4.677,5.198 1.813,0.26 10 false Multiplex Network Door ECU 4.969,4.938 6.781,5.198 1.813,0.26 10 false Combination Meter Assembly 5.792,0.948 7.156,1.219 1.365,0.271 10 false from IG1 NO. 3 Relay 4.906,0.604 5.365,0.802 0.458,0.198 10 false PBD 4.792,1.125 5.781,1.365 0.99,0.24 10 false IG1 NO. 3 5.948,3.365 6.938,3.604 0.99,0.24 10 false MPX-B NO. 1 5.792,0.427 6.781,0.667 0.99,0.24 10 false from Battery 4.75,3.167 5.74,3.406 0.99,0.24 10 false from Battery 3.219,0.427 3.552,0.594 0.333,0.167 10 false OSL 3.219,1.781 3.594,1.979 0.375,0.198 10 false OSR 3.24,4.083 3.646,4.271 0.406,0.188 10 false MSW 3.229,2.938 3.635,3.125 0.406,0.188 10 false OSE 3.75,1.74 4.198,1.917 0.448,0.177 10 false ECUB 4.031,0.448 4.229,0.646 0.198,0.198 10 false B 3.969,0.969 4.177,1.146 0.208,0.177 10 false IG 3.833,3.635 4.208,3.813 0.375,0.177 10 false GND 5.323,1.729 5.667,1.938 0.344,0.208 10 false 4H 6.313,1.729 6.656,1.938 0.344,0.208 10 false 4F 5.323,1.531 5.667,1.74 0.344,0.208 10 false 32 6.323,1.531 6.667,1.74 0.344,0.208 10 false 32 5.25,2.073 6.865,2.5 1.615,0.427 10 false Instrument Panel Junction Block Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

The power back door system uses the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the power back door system after confirming that the communication system is functioning properly.

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.INITIALIZE MULTIPLEX NETWORK DOOR ECU
a.

Perform the initialization for the multiplex network door ECU.

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>INITIALIZATION


Result:
Proceed to
NEXT



NEXT

2.CHECK POWER BACK DOOR SYSTEM
2.CHECK POWER BACK DOOR SYSTEM
a.

Check power back door system operation.

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>OPERATION CHECK


Result:
Result Proceed to
Power back door system operates normally A
Power back door system does not operate B



A

END

B

3.CHECK BACK DOOR CLOSER SYSTEM
3.CHECK BACK DOOR CLOSER SYSTEM
a.

Check back door closer system operation.

Click hereVehicle Exterior>DOOR / HATCH>BACK DOOR CLOSER SYSTEM>OPERATION CHECK


Result:
Result Proceed to
Back door closer system operates normally A
Back door closer system does not operate B



A

4.CHECK COMBINATION METER ASSEMBLY

B

4.CHECK COMBINATION METER ASSEMBLY
a.

Check shift position indicator operation and check that the speedometer indicates 0 km/h (0 mph) when the vehicle is stopped with the engine is idling.


Result:
Result Proceed to
Combination meter assembly operates normally A
Combination meter assembly does not operate B



A

5.CHECK FOR DTC

B

5.CHECK FOR DTC
a.

Check for DTCs.

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>DTC CHECK / CLEAR

Body Electrical > Back Door > Trouble Codes
50001 159

Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

6.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK DOOR ECU - BATTERY AND BODY GROUND)

B

6.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK DOOR ECU - BATTERY AND BODY GROUND)
a.
B358078
1.521,0.333 1.917,0.594 0.396,0.26 1.5,2.521 1.896,2.781 0.396,0.26 0.563,2.063 0.771,1.438 false 2.115,2.031 1.802,1.458 false 1.458,4.052 1.625,3.688 false 2.146,4.073 1.833,3.667 false 1.656,0.385 2.115,0.583 0.458,0.198 10 false X6 1.635,2.573 2.094,2.771 0.458,0.198 10 false X7 0.448,2.083 1.063,2.281 0.615,0.198 10 false ECUB 2.063,2.063 2.354,2.281 0.292,0.219 10 false IG 1.25,4.073 1.865,4.271 0.615,0.198 10 false GND 2.198,4.094 2.49,4.313 0.292,0.219 10 false B 0.24,0.167 0.563,0.406 0.323,0.24 10 false *a
*a Front view of wire harness connector
(to Multiplex Network Door ECU)


Disconnect the X6 and X7 multiplex network door ECU connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
X7-7 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
X6-1 (ECUB) - Body ground Always 11 to 14 V
X7-8 (B) - Body ground Always 11 to 14 V
X6-7 (IG) - Body ground Engine switch on (IG) 11 to 14 V
X6-7 (IG) - Body ground Engine switch off Below 1 V



Result:
Proceed to
OK
NG



OK

7.READ VALUE USING GTS

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Back Door / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Back Door > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
PBD Touch Sensor (Right) Power back door sensor assembly RH signal ON, OFF or Open ON: Power back door sensor assembly RH pressed
OFF: Power back door sensor assembly RH not pressed
Open: Power back door sensor assembly RH circuit open
-
PBD Touch Sensor (Left) Power back door sensor assembly LH signal ON, OFF or Open ON: Power back door sensor assembly LH pressed
OFF: Power back door sensor assembly LH not pressed
Open: Power back door sensor assembly LH circuit open
-
Body Electrical > Back Door > Data List
Tester Display
PBD Touch Sensor (Right)
PBD Touch Sensor (Left)
50003 159 5,6

Result:
Result Proceed to
On the GTS screen, ON or OFF is displayed accordingly A
On the GTS screen, ON or OFF is not displayed accordingly or Open is displayed for power back door sensor assembly RH B
On the GTS screen, ON or OFF is not displayed accordingly or Open is displayed for power back door sensor assembly LH C



A

8.READ VALUE USING GTS

B

11.INSPECT POWER BACK DOOR SENSOR ASSEMBLY RH

C

13.INSPECT POWER BACK DOOR SENSOR ASSEMBLY LH
8.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Back Door / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Back Door > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
PBD Main SW Door control switch signal ON or OFF ON: Door control switch on
OFF: Door control switch off
-
Body Electrical > Back Door > Data List
Tester Display
PBD Main SW
50003 159 7
OK:

On the GTS screen, ON or OFF is displayed accordingly.



Result:
Proceed to
OK
NG



OK

REPLACE MULTIPLEX NETWORK DOOR ECU

NG

9.INSPECT DOOR CONTROL SWITCH
9.INSPECT DOOR CONTROL SWITCH
a.

Remove the door control switch.

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR MAIN SWITCH>REMOVAL


b.

Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (DOOR CONTROL SWITCH - MULTIPLEX NETWORK DOOR ECU AND BODY GROUND)

NG

10.CHECK HARNESS AND CONNECTOR (DOOR CONTROL SWITCH - MULTIPLEX NETWORK DOOR ECU AND BODY GROUND)
a.

Disconnect the F52 door control switch connector.


b.

Disconnect the X6 multiplex network door ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F52-2 (MSW) - X6-20 (MSW) Always Below 1 Ω
F52-1 (MSE) - Body ground Always Below 1 Ω
F52-2 (MSW) or X6-20 (MSW) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MULTIPLEX NETWORK DOOR ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.INSPECT POWER BACK DOOR SENSOR ASSEMBLY RH
a.

Remove the power back door sensor assembly RH.

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR TOUCH SENSOR>REMOVAL


b.

Inspect the power back door sensor assembly RH.

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR TOUCH SENSOR>INSPECTION


Result:
Proceed to
OK
NG



OK

12.CHECK HARNESS AND CONNECTOR (POWER BACK DOOR SENSOR ASSEMBLY RH - MULTIPLEX NETWORK DOOR ECU)

NG

REPLACE POWER BACK DOOR SENSOR ASSEMBLY RH

12.CHECK HARNESS AND CONNECTOR (POWER BACK DOOR SENSOR ASSEMBLY RH - MULTIPLEX NETWORK DOOR ECU)
a.

Disconnect the X24 power back door sensor assembly RH connector.


b.

Disconnect the X6 multiplex network door ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
X24-1 (OSR) - X6-16 (OSR) Always Below 1 Ω
X24-2 (OSRE) - X6-17 (OSE) Always Below 1 Ω
X24-1 (OSR) or X6-16 (OSR) - Body ground Always 10 kΩ or higher
X24-2 (OSRE) or X6-17 (OSE) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MULTIPLEX NETWORK DOOR ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.INSPECT POWER BACK DOOR SENSOR ASSEMBLY LH
a.

Remove the power back door sensor assembly LH.

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR TOUCH SENSOR>REMOVAL


b.

Inspect the power back door sensor assembly LH.

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR TOUCH SENSOR>INSPECTION


Result:
Proceed to
OK
NG



OK

14.CHECK HARNESS AND CONNECTOR (POWER BACK DOOR SENSOR ASSEMBLY LH - MULTIPLEX NETWORK DOOR ECU)

NG

REPLACE POWER BACK DOOR SENSOR ASSEMBLY LH

14.CHECK HARNESS AND CONNECTOR (POWER BACK DOOR SENSOR ASSEMBLY LH - MULTIPLEX NETWORK DOOR ECU)
a.

Disconnect the X2 power back door sensor assembly LH connector.


b.

Disconnect the X6 multiplex network door ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
X2-1 (OSL) - X6-18 (OSL) Always Below 1 Ω
X2-2 (OSLE) - X6-17 (OSE) Always Below 1 Ω
X2-1 (OSL) or X6-18 (OSL) - Body ground Always 10 kΩ or higher
X2-2 (OSLE) or X6-17 (OSE) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MULTIPLEX NETWORK DOOR ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR