Home › Drivetrain › MF1A (TRANSFER / 4WD / AWD) › DYNAMIC TORQUE CONTROL 4WD/AWD SYSTEM
RM3160E _52 Drivetrain _019685 MF1A TRANSFER / 4WD / AWD _0109466 DYNAMIC TORQUE CONTROL 4WD/AWD SYSTEM C

MF1A TRANSFER / 4WD / AWD  DYNAMIC TORQUE CONTROL 4WD/AWD SYSTEM  C1297/97  Steering Angle Sensor  


DESCRIPTION

·

The 4WD ECU assembly determines that the vehicle is turning based on the signals sent from the steering sensor.

·

The steering sensor signal is sent to the 4WD ECU assembly via the CAN communication system.


DTC No. Detection Item DTC Detection Condition Trouble Area Memory
C1297/97 Steering Angle Sensor When the voltage of 4WD ECU assembly IG terminal is 9.5 V or more, a steering sensor malfunction signal is received.
·

Steering sensor

·

CAN communication system

·

4WD ECU assembly

·

Brake control system


DTC stored

CAUTION / NOTICE / HINT

HINT:

Check the condition of each related circuit connector before troubleshooting.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE


PROCEDURE

1.CHECK FOR DTC
a.

Clear the DTCs.

Click hereDrivetrain>MF1A (TRANSFER / 4WD / AWD)>DYNAMIC TORQUE CONTROL 4WD/AWD SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRAC > Clear DTCs
50002 105

b.

Turn the ignition switch off.


c.

Turn the ignition switch to ON again and check that no CAN communication system DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


d.

Start the engine.


e.

Drive the vehicle at a speed of 35 km/h (22 mph), turn the steering wheel to the right and left and check that no brake control system (steering sensor) DTCs (C1432, C1433 or C1434) are output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRAC > Trouble Codes
50001 105
HINT:

When DTCs indicating a CAN communication system malfunction are output, repair the CAN communication system before repairing each corresponding sensor.



Result:
Result Proceed to
Neither CAN communication system DTCs nor brake control system DTCs are output A
CAN communication system DTCs are output B
Brake control system (steering sensor) DTCs (C1432, C1433 or C1434) are output C



A

2.READ VALUE USING GTS (STEERING ANGLE VALUE)

B

GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

C

REPAIR CIRCUIT INDICATED BY OUTPUT CODE (BRAKE CONTROL SYSTEM)

2.READ VALUE USING GTS (STEERING ANGLE VALUE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / Four Wheel Drive / Data List.


e.

Read the value displayed on the GTS.

Chassis > Four Wheel Drive > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Steering Angle Value Steering angle value Min.: -3276.8°
Max.: 3276.7°
Left turn: Increases
Right turn: Decreases
Changes in proportion with the amount of steering wheel rotation during steering operation.
Chassis > Four Wheel Drive > Data List
Tester Display
Steering Angle Value
50003 118 8
OK:

The steering angle sensor value changes in accordance with the steering wheel movement.



Result:
Proceed to
OK
NG



OK

NG