Home › Drivetrain › MF1A (TRANSFER / 4WD / AWD) › DYNAMIC TORQUE CONTROL 4WD/AWD SYSTEM
RM3160E _52 Drivetrain _019685 MF1A TRANSFER / 4WD / AWD _0109466 DYNAMIC TORQUE CONTROL 4WD/AWD SYSTEM J

MF1A TRANSFER / 4WD / AWD  DYNAMIC TORQUE CONTROL 4WD/AWD SYSTEM  AWD Control Switch Circuit  


DESCRIPTION

The 4WD ECU assembly changes the control mode in response to "Auto Mode" and "Lock Mode" signals from the AWD lock switch (differential lock switch).

WIRING DIAGRAM

C264643
2.188,0.927 2.344,1.073 0.156,0.146 10 false 6 4.01,0.938 4.146,1.083 0.135,0.146 10 false 9 2.333,0.927 2.792,1.094 0.458,0.167 10 false GND 3.844,0.938 4.01,1.104 0.167,0.167 10 false B 5.313,0.927 5.594,1.094 0.281,0.167 10 false 10 5.563,1.052 6.083,1.229 0.521,0.177 10 false 4WDL 2.448,1.552 2.781,1.708 0.333,0.156 10 false F56 2.458,1.719 4.01,2.083 1.552,0.365 10 false AWD Lock Switch (Differential Lock Switch) 5.333,1.813 5.656,2 0.323,0.188 10 false F14 5.323,2.01 6.677,2.198 1.354,0.188 10 false 4WD ECU Assembly

CAUTION / NOTICE / HINT

HINT:

Check the condition of each related circuit connector before troubleshooting.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE


PROCEDURE

1.INSPECT 4WD LOCK LIGHT
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / Four Wheel Drive / Active Test

Chassis > Four Wheel Drive > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
4WD LOCK Light AWD lock mode indicator light Indicator light OFF/ON Observe combination meter assembly
Chassis > Four Wheel Drive > Active Test
Tester Display
4WD LOCK Light
50004 118 5

f.

When performing the 4WD Warning Light Active Test, check 4WD Warning Light in the Data List.

Chassis > Four Wheel Drive > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
4WD LOCK Light AWD lock mode indicator light OFF or ON OFF: AWD lock mode indicator light off
OFF: AWD lock mode indicator light on
-
Chassis > Four Wheel Drive > Data List
Tester Display
4WD LOCK Light
50003 118 35

Result:
Result Proceed to
Changes between ON and OFF A
Does not change between ON and OFF B



A

2.INSPECT DIFFERENTIAL LOCK SWITCH

B

2.INSPECT DIFFERENTIAL LOCK SWITCH
a.

Remove the AWD lock switch (differential lock switch).

Click hereDrivetrain>MF1A (TRANSFER / 4WD / AWD)>4WD CONTROL SWITCH>REMOVAL


b.

Inspect the AWD lock switch (differential lock switch).

Click hereDrivetrain>MF1A (TRANSFER / 4WD / AWD)>4WD CONTROL SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (DIFFERENTIAL LOCK SWITCH - BODY GROUND)

NG

3.CHECK HARNESS AND CONNECTOR (DIFFERENTIAL LOCK SWITCH - BODY GROUND)
a.
C278711
1.583,0.135 1.958,0.375 0.375,0.24 1.323,1.344 0.667,1.052 false 0,0 0.313,0.156 0.313,0.156 10 false *a 1.656,0.167 2.115,0.365 0.458,0.198 10 false F56 0.313,0.948 0.771,1.146 0.458,0.198 10 false GND
*a Front view of wire harness connector
(to AWD Lock Switch (Differential Lock Switch))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F56-6 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (DIFFERENTIAL LOCK SWITCH - 4WD ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (DIFFERENTIAL LOCK SWITCH - 4WD ECU ASSEMBLY)
a.

Reinstall the AWD lock switch (differential lock switch).

Click hereDrivetrain>MF1A (TRANSFER / 4WD / AWD)>4WD CONTROL SWITCH>INSTALLATION


b.

Disconnect the F14 4WD ECU assembly connector.


c.
C270074
2.385,0.104 2.792,0.365 0.406,0.26 1.167,1.917 1.5,1.917 1.5,1.917 1.583,1.5 true 0.656,1.833 1.083,2 0.427,0.167 10 false 4WDL 2.49,0.146 2.802,0.344 0.313,0.198 10 false F14 0,0 0.313,0.156 0.313,0.156 10 false *a
*a Front view of wire harness connector
(to 4WD ECU Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F14-10 (4WDL) - Body ground AWD lock switch on Below 1 Ω
AWD lock switch off 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR