Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PARKING ASSIST MONITOR SYSTEM › 2013.12–2016.11
RM3160E _56 Audio / Visual / Telematics _019702 PARK ASSIST / MONITORING _0109513 PARKING ASSIST MONITOR SYSTEM C

PARK ASSIST / MONITORING  PARKING ASSIST MONITOR SYSTEM  C1622  Back Camera Disconnected  


DESCRIPTION

This DTC is stored if the navigation receiver assembly*1 or radio and display receiver assembly*2 judges that the signals or signal lines between the television camera assembly, and the navigation receiver assembly*1 or radio and display receiver assembly*2 are not normal as a result of its self check.

*1: for Navigation Receiver Type

*2: for Radio and Display Type


DTC No. Detection Item DTC Detection Condition Trouble Area
C1622 Back Camera Disconnected Open or short in the television camera assembly signal circuit
·

Harness or connector

·

Television camera assembly

·

Navigation receiver assembly (for Navigation Receiver Type)

·

Radio and display receiver assembly (for Radio and Display Type)



WIRING DIAGRAM

E292561
0.26,2.583 2.417,2.896 2.156,0.313 10 false Navigation Receiver Assembly*1 1.865,2.104 2.208,2.281 0.344,0.177 10 false F114 1.875,0.333 2.198,0.49 0.323,0.156 10 false 11*1 2.292,2.104 2.594,2.323 0.302,0.219 10 false F69 1.854,0.521 2.177,0.677 0.323,0.156 10 false F117 1.865,1.708 2.188,1.865 0.323,0.156 10 false F117 1.865,1.323 2.188,1.479 0.323,0.156 10 false F117 1.865,0.917 2.188,1.073 0.323,0.156 10 false F117 2.302,1.708 2.604,1.927 0.302,0.219 10 false F72 2.302,0.927 2.604,1.146 0.302,0.219 10 false F72 2.292,1.313 2.594,1.531 0.302,0.219 10 false F72 2.302,0.521 2.604,0.74 0.302,0.219 10 false F72 1.885,1.125 2.208,1.281 0.323,0.156 10 false 24*1 1.885,1.51 2.208,1.667 0.323,0.156 10 false 23*1 1.917,1.917 2.24,2.073 0.323,0.156 10 false 7*1 1.875,0.729 2.198,0.885 0.323,0.156 10 false 12*1 2.271,0.333 2.594,0.49 0.323,0.156 10 false 11*2 2.26,0.729 2.583,0.885 0.323,0.156 10 false 12*2 2.281,1.125 2.604,1.281 0.323,0.156 10 false 24*2 2.281,1.521 2.604,1.677 0.323,0.156 10 false 23*2 2.313,1.917 2.635,2.073 0.323,0.156 10 false 7*2 1.448,0.5 1.771,0.656 0.323,0.156 10 false CA+ 1.542,0.927 1.76,1.083 0.219,0.156 10 false V+ 1.573,1.313 1.771,1.49 0.198,0.177 10 false V- 1.333,1.708 1.927,1.958 0.594,0.25 10 false CGND 5.458,0.531 5.875,0.688 0.417,0.156 10 false CB+ 5.469,1.323 5.885,1.479 0.417,0.156 10 false CV- 5.469,0.927 5.885,1.083 0.417,0.156 10 false CV+ 5.469,1.719 5.885,1.875 0.417,0.156 10 false CGND 5.219,0.427 5.385,0.583 0.167,0.156 10 false 6 5.229,0.823 5.323,0.979 0.094,0.156 10 false 3 5.229,1.615 5.375,1.781 0.146,0.167 10 false 5 3.833,1.5 4.083,1.667 0.25,0.167 10 false *3 5.167,2.24 5.5,2.406 0.333,0.167 10 false X13 5.167,2.385 7.052,2.75 1.885,0.365 10 false Television Camera Assembly 2.677,3.365 4.583,3.698 1.906,0.333 10 false *2: for Radio and Display Type 0.25,3.365 2.74,3.698 2.49,0.333 10 false *1: for Navigation Receiver Type 5,3.365 5.958,3.698 0.958,0.333 10 false *3: Shielded 0.25,2.906 2.75,3.271 2.5,0.365 10 false Radio and Display Receiver Assembly*2 5.229,1.219 5.375,1.385 0.146,0.167 10 false 2 1.365,2.104 1.76,2.281 0.396,0.177 10 false GND1

CAUTION / NOTICE / HINT

NOTICE:
·

If the cable from the negative (-) battery terminal was disconnected, the estimated course lines may not be displayed on the image of the area behind the vehicle. In this case, perform "Correct the Steering Angle Neutral Point".

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM>INITIALIZATION

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM>CALIBRATION



PROCEDURE

1.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
for Navigation Receiver Type A
for Radio and Display Type B



A

2.CHECK HARNESS AND CONNECTOR (TELEVISION CAMERA ASSEMBLY - NAVIGATION RECEIVER ASSEMBLY)

B

5.CHECK HARNESS AND CONNECTOR (TELEVISION CAMERA ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (TELEVISION CAMERA ASSEMBLY - NAVIGATION RECEIVER ASSEMBLY)
a.

Disconnect the X13 television camera assembly connector.


b.

Disconnect the F117 navigation receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
X13-6 (CB+) - F117-11 (CA+) Always Below 1 Ω
X13-3 (CV+) - F117-12 (V+) Always Below 1 Ω
X13-2 (CV-) - F117-24 (V-) Always Below 1 Ω
X13-5 (CGND) - F117-23 (CGND) Always Below 1 Ω
X13-6 (CB+) - Body ground Always 10 kΩ or higher
X13-3 (CV+) - Body ground Always 10 kΩ or higher
X13-2 (CV-) - Body ground Always 10 kΩ or higher
X13-5 (CGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT NAVIGATION RECEIVER ASSEMBLY (V-, CGND, CA+)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT NAVIGATION RECEIVER ASSEMBLY (V-, CGND, CA+)
a.

Reconnect the F117 navigation receiver assembly connector.


b.
E271917
1.521,0.188 1.969,0.479 0.448,0.292 1.302,1.813 1.229,1.313 false 0.74,1.833 1.104,1.313 false 0.813,0.771 1.229,1.125 false 1.604,0.26 1.99,0.448 0.385,0.188 10 false F117 0.573,1.813 0.885,2.01 0.313,0.198 10 false V- 1.146,1.823 1.771,2.052 0.625,0.229 10 false CGND 0.5,0.646 1.125,0.875 0.625,0.229 10 false CA+ 0.115,0.073 0.74,0.302 0.625,0.229 10 false *a
*a Component with harness connected
(Navigation Receiver Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F117-24 (V-) - Body ground Always Below 1 Ω
F117-23 (CGND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F117-11 (CA+) - F117-23 (CGND) Engine switch on (ACC) 5.5 to 7.05 V



Result:
Proceed to
OK
NG



OK

4.INSPECT NAVIGATION RECEIVER ASSEMBLY (V+, GND1)

NG

4.INSPECT NAVIGATION RECEIVER ASSEMBLY (V+, GND1)
a.

Reconnect the X13 television camera assembly connector.


b.
E279721
1.479,0.208 1.896,0.5 0.417,0.292 1.479,2.396 1.927,2.677 0.448,0.281 0.729,0.823 1.115,1.198 false 1.854,3.698 2.5,4.188 false 0.094,0.083 0.438,0.25 0.344,0.167 10 false *a 2.521,4.219 2.948,4.396 0.427,0.177 10 false GND1 1.542,0.271 1.885,0.438 0.344,0.167 10 false F117 1.563,2.469 1.906,2.635 0.344,0.167 10 false F114 0.51,0.688 0.854,0.854 0.344,0.167 10 false V+
*a Component with harness connected
(Navigation Receiver Assembly)


E265840C05
0.823,2.073 1,2.073 1,2.073 1.125,1.583 false 1.479,2.063 1.344,2.063 1.344,2.063 1.229,1.479 false 0.781,4.167 0.958,4.167 0.958,4.167 1.156,3.594 false 1.521,4.125 1.385,4.125 1.385,4.125 1.271,3.542 false 0.229,0.229 0.542,0.427 0.313,0.198 10 *a 0.396,1.052 0.76,1.313 0.365,0.26 10 GND 0.396,3.208 0.76,3.469 0.365,0.26 10 GND 0.26,2.271 0.625,2.531 0.365,0.26 10 *b 0.646,4.073 1.01,4.333 0.365,0.26 10 *c 0.656,1.979 1.021,2.24 0.365,0.26 10 *c 1.51,1.969 1.875,2.229 0.365,0.26 10 *d 1.542,4.052 1.906,4.313 0.365,0.26 10 *d
*a Waveform 1 (camera lens is not covered, displaying an image)
*b Waveform 2 (camera lens is covered, blacking out the screen)
*c Synchronization Signal
*d Video Waveform


Using an oscilloscope, check the waveform of the television camera assembly.

HINT:

A waterproof connector is used for the television camera assembly. Therefore, inspect the waveform at the navigation receiver assembly with the connector connected.


OK:

Waveform is similar to that shown in the illustration.

Item Content
Measurement terminal F117-12 (V+) - F114-7 (GND1)
Measurement setting 200 mV/DIV., 50 μs./DIV.
Condition Engine switch on (IG), shift lever in R


HINT:
·

The video waveform changes according to the image sent by the television camera assembly.

·

The video waveform is constantly output when the engine switch is on (ACC).




Result:
Proceed to
OK
NG



OK

NG

5.CHECK HARNESS AND CONNECTOR (TELEVISION CAMERA ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.

Disconnect the X13 television camera assembly connector.


b.

Disconnect the F72 radio and display receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
X13-6 (CB+) - F72-11 (CA+) Always Below 1 Ω
X13-3 (CV+) - F72-12 (V+) Always Below 1 Ω
X13-2 (CV-) - F72-24 (V-) Always Below 1 Ω
X13-5 (CGND) - F72-23 (CGND) Always Below 1 Ω
X13-6 (CB+) - Body ground Always 10 kΩ or higher
X13-3 (CV+) - Body ground Always 10 kΩ or higher
X13-2 (CV-) - Body ground Always 10 kΩ or higher
X13-5 (CGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY (V-, CGND, CA+)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY (V-, CGND, CA+)
a.

Reconnect the F72 radio and display receiver assembly connector.


b.
E271917C19
1.521,0.188 1.969,0.479 0.448,0.292 1.302,1.813 1.229,1.313 false 0.74,1.833 1.104,1.313 false 0.813,0.771 1.229,1.125 false 1.635,0.25 2.021,0.438 0.385,0.188 10 false F72 0.573,1.813 0.885,2.01 0.313,0.198 10 false V- 1.146,1.823 1.771,2.052 0.625,0.229 10 false CGND 0.5,0.646 1.125,0.875 0.625,0.229 10 false CA+ 0.115,0.073 0.74,0.302 0.625,0.229 10 false *a
*a Component with harness connected
(Radio and Display Receiver Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F72-24 (V-) - Body ground Always Below 1 Ω
F72-23 (CGND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F72-11 (CA+) - F72-23 (CGND) Engine switch on (ACC) 5.5 to 7.05 V



Result:
Proceed to
OK
NG



OK

7.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY (V+, GND1)

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

7.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY (V+, GND1)
a.

Reconnect the X13 television camera assembly connector.


b.
E279721C09
1.479,0.208 1.896,0.5 0.417,0.292 1.479,2.396 1.927,2.677 0.448,0.281 0.729,0.823 1.115,1.198 false 1.854,3.698 2.5,4.188 false 0.094,0.083 0.438,0.25 0.344,0.167 10 false *a 2.521,4.219 2.948,4.396 0.427,0.177 10 false GND1 1.583,0.26 1.927,0.427 0.344,0.167 10 false F72 1.604,2.448 1.948,2.615 0.344,0.167 10 false F69 0.51,0.688 0.854,0.854 0.344,0.167 10 false V+
*a Component with harness connected
(Radio and Display Receiver Assembly)


E265840C05
0.823,2.073 1,2.073 1,2.073 1.125,1.583 false 1.479,2.063 1.344,2.063 1.344,2.063 1.229,1.479 false 0.781,4.167 0.958,4.167 0.958,4.167 1.156,3.594 false 1.521,4.125 1.385,4.125 1.385,4.125 1.271,3.542 false 0.229,0.229 0.542,0.427 0.313,0.198 10 *a 0.396,1.052 0.76,1.313 0.365,0.26 10 GND 0.396,3.208 0.76,3.469 0.365,0.26 10 GND 0.26,2.271 0.625,2.531 0.365,0.26 10 *b 0.646,4.073 1.01,4.333 0.365,0.26 10 *c 0.656,1.979 1.021,2.24 0.365,0.26 10 *c 1.51,1.969 1.875,2.229 0.365,0.26 10 *d 1.542,4.052 1.906,4.313 0.365,0.26 10 *d
*a Waveform 1 (camera lens is not covered, displaying an image)
*b Waveform 2 (camera lens is covered, blacking out the screen)
*c Synchronization Signal
*d Video Waveform


Using an oscilloscope, check the waveform of the television camera assembly.

HINT:

A waterproof connector is used for the television camera assembly. Therefore, inspect the waveform at the radio and display receiver assembly with the connector connected.


OK:

Waveform is similar to that shown in the illustration.

Item Content
Measurement terminal F72-12 (V+) - F69-7 (GND1)
Measurement setting 200 mV/DIV., 50 μs./DIV.
Condition Engine switch on (IG), shift lever in R


HINT:
·

The video waveform changes according to the image sent by the television camera assembly.

·

The video waveform is constantly output when the engine switch is on (ACC).




Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG