This DTC is stored if the television camera assembly judges as a result of its self check that the signals or signal lines between the television camera assembly and navigation receiver assembly*1 or radio and display receiver assembly*2 are not normal.
*1: for Navigation Receiver Type
*2: for Radio and Display Type
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1621 | Back Camera Power Supply Failure | Television camera assembly power supply failure | ·
Harness or connector ·
Television camera assembly ·
Navigation receiver assembly (for Navigation Receiver Type) ·
Radio and display receiver assembly (for Radio and Display Type) |
If the cable from the negative (-) battery terminal was disconnected, the estimated course lines may not be displayed on the image of the area behind the vehicle. In this case, perform "Correct the Steering Angle Neutral Point".
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM>INITIALIZATION
Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system may be needed.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM>CALIBRATION
Choose the model to be inspected.
| Result | Proceed to |
|---|---|
| for Navigation Receiver Type | A |
| for Radio and Display Type | B |
A
B
Disconnect the F117 navigation receiver assembly connector.
Disconnect the X13 television camera assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F117-11 (CA+) - X13-6 (CB+) | Always | Below 1 Ω |
| F117-23 (CGND) - X13-5 (CGND) | Always | Below 1 Ω |
| F117-11 (CA+) - F117-23 (CGND) | Always | 10 kΩ or higher |
| F117-11 (CA+) - Body ground | Always | 10 kΩ or higher |
| F117-23 (CGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the F117 navigation receiver assembly connector.
| *a | Component with harness connected
(Navigation Receiver Assembly) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F117-11 (CA+) - F117-23 (CGND) | Engine switch on (ACC) | 5.5 to 7.05 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F72 radio and display receiver assembly connector.
Disconnect the X13 television camera assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F72-11 (CA+) - X13-6 (CB+) | Always | Below 1 Ω |
| F72-23 (CGND) - X13-5 (CGND) | Always | Below 1 Ω |
| F72-11 (CA+) - F72-23 (CGND) | Always | 10 kΩ or higher |
| F72-11 (CA+) - Body ground | Always | 10 kΩ or higher |
| F72-23 (CGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the F72 radio and display receiver assembly connector.
| *a | Component with harness connected
(Radio and Display Receiver Assembly) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F72-11 (CA+) - F72-23 (CGND) | Engine switch on (ACC) | 5.5 to 7.05 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG