Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM › 2013.12–2016.11
RM3160E _56 Audio / Visual / Telematics _019702 PARK ASSIST / MONITORING _0109515 BLIND SPOT MONITOR SYSTEM J

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  Main Switch Circuit  


DESCRIPTION

When the blind spot monitor main switch (warning canceling switch assembly) is turned on, a signal is sent to the blind spot monitor sensor LH and the blind spot monitor indicator on the blind spot monitor main switch (warning canceling switch assembly) illuminates. The blind spot monitor system operates according to this signal.

WIRING DIAGRAM

E258614
5.438,0.594 5.885,0.76 0.448,0.167 10 false BSSW 5.438,0.979 5.885,1.146 0.448,0.167 10 false BIND 4.875,0.906 5.146,1.167 0.271,0.26 10 false 12 5.26,0.542 5.365,0.719 0.104,0.177 10 false 8 5.26,0.906 5.365,1.083 0.104,0.177 10 false 3 4.885,0.542 5.073,0.823 0.188,0.281 10 false 8 4.688,0.542 4.833,0.719 0.146,0.177 10 false D 4.688,0.906 4.833,1.083 0.146,0.177 10 false E 3.333,0.542 3.583,0.76 0.25,0.219 10 false B 3.063,0.51 3.438,0.76 0.375,0.25 10 false 11 5.146,1.917 5.573,2.063 0.427,0.146 10 false M31 5.146,2.073 7.021,2.344 1.875,0.271 10 false Blind Spot Monitor Sensor LH 2.375,0.813 3.406,1.083 1.031,0.271 10 false DSS-IG 0.208,0.635 1.573,0.969 1.365,0.333 10 false from IG1 NO. 3 Relay 3.083,1.292 3.531,1.448 0.448,0.156 10 false F3 3.073,1.458 5,2.083 1.927,0.625 10 false Blind Spot Monitor Main Switch (Warning Canceling Switch Assembly)

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK BLIND SPOT MONITOR MAIN SWITCH (WARNING CANCELING SWITCH ASSEMBLY)
a.

Check that the blind spot monitor indicator on the blind spot monitor main switch (warning canceling switch assembly) illuminates normally when the blind spot monitor main switch (warning canceling switch assembly) is turned from off to on.


b.

Check that the blind spot monitor indicator on the blind spot monitor main switch (warning canceling switch assembly) turns off normally when the blind spot monitor main switch (warning canceling switch assembly) is turned from on to off.

OK:

The blind spot monitor indicator operates normally.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.READ VALUE USING GTS
2.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Blind Spot Monitor Master / Data List.


e.

According to the display on GTS, read the Data List.

Body Electrical > Blind Spot Monitor Master > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Main Switch State of the blind spot monitor main switch (warning canceling switch assembly) OFF or ON OFF: Blind spot monitor main switch (warning canceling switch assembly) off
ON: Blind spot monitor main switch (warning canceling switch assembly) on
-
Body Electrical > Blind Spot Monitor Master > Data List
Tester Display
Main Switch
50003 313 2

Result:
Result Proceed to
The display does not change as shown above when the blind spot monitor main switch (warning canceling switch assembly) is operated. A
The display changes as shown above when the blind spot monitor main switch (warning canceling switch assembly) is operated. B



A

3.INSPECT BLIND SPOT MONITOR MAIN SWITCH (WARNING CANCELING SWITCH ASSEMBLY)

B

6.INSPECT BLIND SPOT MONITOR MAIN SWITCH (WARNING CANCELING SWITCH ASSEMBLY)
3.INSPECT BLIND SPOT MONITOR MAIN SWITCH (WARNING CANCELING SWITCH ASSEMBLY)
a.

Remove the blind spot monitor main switch (warning canceling switch assembly).

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR MAIN SWITCH>REMOVAL


b.
E224422
1.49,1.469 1.281,1.802 false 2,1.469 2.208,1.802 false 0.323,0.198 0.635,0.49 0.313,0.292 10 false *a 2.188,1.823 2.354,1.969 0.167,0.146 10 false D 1.219,1.823 1.385,1.969 0.167,0.146 10 false B
*a Component without harness connected
(Blind Spot Monitor Main Switch (Warning Canceling Switch Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
11 (B) - 8 (D) Blind spot monitor main switch on (not protruding) Below 1 Ω
11 (B) - 8 (D) Blind spot monitor main switch off (protruding) 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR MAIN SWITCH - BATTERY)

NG

REPLACE BLIND SPOT MONITOR MAIN SWITCH (WARNING CANCELING SWITCH ASSEMBLY)

4.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR MAIN SWITCH - BATTERY)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F3-11 (B) - Body ground Engine switch on (IG) 11 to 14 V
F3-11 (B) - Body ground Engine switch off Below 1 V



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR MAIN SWITCH - BLIND SPOT MONITOR SENSOR LH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR MAIN SWITCH - BLIND SPOT MONITOR SENSOR LH)
a.

Disconnect the M31 blind spot monitor sensor LH connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M31-8 (BSSW) - F3-8 (D) Always Below 1 Ω
M31-8 (BSSW) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT BLIND SPOT MONITOR MAIN SWITCH (WARNING CANCELING SWITCH ASSEMBLY)
a.

Remove the blind spot monitor main switch (warning canceling switch assembly).

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR MAIN SWITCH>REMOVAL


b.
E224422
1.479,1.448 1.75,1.844 false 1.323,1.458 1.083,1.833 false 0.323,0.198 0.635,0.49 0.313,0.292 10 false *a 1.75,1.854 1.917,2 0.167,0.146 10 false B 1,1.854 1.167,2 0.167,0.146 10 false E
*a Component without harness connected
(Blind Spot Monitor Main Switch (Warning Canceling Switch Assembly))


Apply battery voltage to the blind spot monitor main switch (warning canceling switch assembly) connector and check the operation of the blind spot monitor indicator, as shown in the table below.

OK:
Tester Connection Condition Specified Condition
Battery positive (+) → Terminal 11 (B)
Battery negative (-) → Terminal 12 (E)
Blind spot monitor main switch on (not protruding) Blind spot monitor indicator illuminates
Blind spot monitor main switch off (protruding) Blind spot monitor indicator does not illuminate



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR MAIN SWITCH - BLIND SPOT MONITOR SENSOR LH)

NG

REPLACE BLIND SPOT MONITOR MAIN SWITCH (WARNING CANCELING SWITCH ASSEMBLY)

7.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR MAIN SWITCH - BLIND SPOT MONITOR SENSOR LH)
a.

Disconnect the M31 blind spot monitor sensor LH connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M31-3 (BIND) - F3-12 (E) Always Below 1 Ω
M31-3 (BIND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR