Home › Engine / Hybrid System › 1AR-FE (ENGINE MECHANICAL) › CYLINDER HEAD GASKET
RM3160E _51 Engine / Hybrid System _019672 1AR-FE ENGINE MECHANICAL _0109591 CYLINDER HEAD GASKET A

1AR-FE ENGINE MECHANICAL  CYLINDER HEAD GASKET  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:

Perform "Inspection After Repair" after replacing the camshaft, No. 2 camshaft, camshaft timing gear assembly, camshaft timing exhaust gear assembly or cylinder head sub-assembly.

Click hereEngine / Hybrid System>1AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


PROCEDURE

Hide 11101A 1.INSPECT CYLINDER HEAD BOLT

Hide 11101 2.INSPECT CYLINDER HEAD SUB-ASSEMBLY

Hide 11115 3.INSTALL CYLINDER HEAD GASKET

a.
A264847C13
2.438,0.146 2.292,0.146 2.292,0.146 2.198,0.448 false 0.781,3.229 0.469,3.646 0.469,3.646 0.469,3.802 false 2.458,0.021 2.646,0.198 0.188,0.177 10 false *a 1.844,3.042 2,3.25 0.156,0.208 10 false *c 2.219,3.927 2.729,4.115 0.51,0.188 10 false 7.0 mm 0.625,2.385 1.51,2.552 0.885,0.167 10 false 3.0 to 7.0 mm 0.802,3.531 0.979,3.719 0.177,0.188 10 false *2 0.385,3.823 0.542,3.99 0.156,0.167 10 false *1 0.26,3 0.438,3.188 0.177,0.188 10 false *b
*1 Cylinder Head Gasket
*2 Cylinder Block Sub-assembly
*a Lot No.
*b 3.0 mm or more
*c 20 mm or more
V100135

Seal Packing
V100136

Front


Clean the cylinder block sub-assembly and cylinder head sub-assembly with solvent.


b.

Apply a continuous line of seal packing to a new cylinder head gasket as shown in the illustration.

Seal Packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard Seal Dimension:

3.0 to 7.0 mm (0.118 to 0.276 in.) wide and 3.0 mm (0.118 in.) or thicker


HINT:

Apply at least 20 mm (0.787 in.) of seal packing from the inside edge of the protrusion of the cylinder block sub-assembly.


NOTICE:
·

Remove any oil from the contact surfaces.

·

Install the cylinder head gasket within 3 minutes and tighten the bolts within 15 minutes of applying seal packing.




c.

Place the new cylinder head gasket on the cylinder block sub-assembly with the Lot No. stamp facing upward.

NOTICE:

Pay attention to the installation direction.



Hide 11101 4.INSTALL CYLINDER HEAD SUB-ASSEMBLY

HINT:

The cylinder head bolts are tightened in 4 progressive steps.


a.

Place the cylinder head sub-assembly on the cylinder block sub-assembly.

NOTICE:
·

Ensure that no oil is on the contact surface of the cylinder head sub-assembly.

·

Place the cylinder head sub-assembly on the cylinder block sub-assembly gently in order not to damage the gasket with the bottom of the cylinder head sub-assembly.




b.

Install the 10 plate washers to the 10 cylinder head bolts.


c.

Apply a light coat of engine oil to the threads and under the heads of the cylinder head bolts.


d.

Step 1:

i.
A196908N19
2.417,0.281 2.521,0.427 0.104,0.146 10 false 9 1.5,1.646 1.594,1.802 0.094,0.156 10 false 1 1.49,0.26 1.583,0.438 0.094,0.177 10 false 2 1.958,1.635 2.073,1.781 0.115,0.146 10 false 3 1.031,0.281 1.125,0.438 0.094,0.156 10 false 4 1.948,0.281 2.063,0.427 0.115,0.146 10 false 5 1.021,1.625 1.135,1.781 0.115,0.156 10 true 6 2.438,1.635 2.563,1.792 0.125,0.156 10 false 7 0.583,0.281 0.75,0.427 0.167,0.146 10 true 8 0.5,1.646 0.802,1.792 0.302,0.146 10 true 10

Using a 10 mm bi-hexagon wrench, install and uniformly tighten the 10 cylinder head bolts in several steps, in the order shown in the illustration.

Torque:
36 N*m (367 kgf*cm, 27 ft.*lbf)

NOTICE:

Do not drop the plate washers for the cylinder head bolts into the cylinder head sub-assembly.




e.

Step 2:

i.

Check that the cylinder head bolts are tightened to the specified torque.

Torque:
36 N*m (367 kgf*cm, 27 ft.*lbf)



f.

Step 3:

i.
A307124C03
1.135,1.74 1.51,1.167 false 1.063,0.417 1.344,0.625 0.281,0.208 10 false 90° 2.438,0.354 2.719,0.563 0.281,0.208 10 false 90° 1.01,1.75 1.323,1.948 0.313,0.198 10 false *a
*a Paint Mark
V100135

Front


Mark each cylinder head bolt head with paint as shown in the illustration.


ii.

Tighten the cylinder head bolts by 90° in the order shown in step 1.



g.

Step 4:

i.

Tighten the cylinder head bolts by another 90° in the order shown in step 1.


ii.

Check that the paint marks are now facing rearward.

NOTICE:
·

Do not apply oil for at least 2 hours after installation.

·

Do not start the engine for at least 2 hours after installation.

·

After installation, if the seal packing has seeped out, wipe it off.



HINT:

Perform "Inspection After Repair" after replacing the cylinder head sub-assembly.

Click hereEngine / Hybrid System>1AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION




Hide 13716 5.INSTALL VALVE STEM CAP

a.

Apply a light coat of engine oil to the valve stem cap ends.


b.

Install the 16 valve stem caps to the cylinder head sub-assembly.

NOTICE:

Do not drop the valve stem caps into the cylinder head sub-assembly.



Hide 13050 6.SET CAMSHAFT TIMING GEAR ASSEMBLY

HINT:

When installing the camshaft timing gear assembly, release the lock pin and set the camshaft timing gear assembly to the advanced position before installation.


a.
A284096C26
0.865,1.729 1.021,1.729 1.021,1.729 1.781,1.333 false 0.771,3.969 0.927,3.969 0.927,3.969 1.688,3.573 false 2.042,1.604 2.458,1.948 2.458,1.948 2.615,1.948 false 2.073,3.677 2.438,3.417 2.438,3.417 2.583,3.417 false 0.083,0.25 0.396,0.406 0.313,0.156 10 false *a 0.083,2.583 0.396,2.74 0.313,0.156 10 false *b 0.708,1.625 1.021,1.781 0.313,0.156 10 false *c 2.667,1.844 2.979,2 0.313,0.156 10 false *d 2.635,3.323 2.948,3.479 0.313,0.156 10 false *d 0.604,3.854 0.917,4.01 0.313,0.156 10 false *c
*a Advanced Position
*b Retarded Position
*c Knock Pin Hole
*d Alignment Mark


Check the camshaft timing gear assembly position.

NOTICE:
·

If the camshaft timing gear assembly is set to the advanced position, do not let the camshaft timing gear assembly rotate clockwise during installation.

·

If the camshaft timing gear assembly has rotated to the most retarded position, make sure to release the lock pin and set the camshaft timing gear assembly to the most advanced position before tightening the bolt of the camshaft timing gear assembly.




b.
A196901C55
1.854,0.625 1.635,0.906 false 1.156,0.167 0.698,0.75 false 1.188,0.063 1.365,0.24 0.177,0.177 10 false *b 1.875,0.521 2.042,0.698 0.167,0.177 10 false *a
*a Knock Pin
*b Pin Hole


Align and fit the knock pin of the camshaft with the pin hole of the camshaft timing gear assembly.


c.
A196904C74
2.146,0.865 1.896,0.865 1.896,0.865 1.5,1.083 false 0.823,0.771 0.917,0.771 0.917,0.771 1.125,0.99 false 0.604,0.667 0.781,0.823 0.177,0.156 10 false *1 1.802,0.531 2,0.698 0.198,0.167 10 false *c 2.188,0.75 2.365,0.917 0.177,0.167 10 false *2 1.74,2.021 1.938,2.177 0.198,0.156 10 false *d 0.063,0.042 0.25,0.208 0.188,0.167 10 false *a 0.063,1.833 0.26,2 0.198,0.167 10 false *b
*1 Camshaft Timing Gear Assembly
*2 Camshaft Flange
*a Incorrect
*b Correct
*c Gap
*d No Gap


Check that there is no gap between the camshaft timing gear assembly and camshaft flange.


d.

Secure the camshaft in place by hand, and then install the bolt of the camshaft timing gear assembly by hand.

NOTICE:

Do not use any tools to install the bolt. If the bolt is installed using a tool, the lock pin will be damaged.



e.

Release the lock pin.

A284097C21
1.417,1.052 1.771,1.052 1.771,1.052 1.917,1.104 false 2.344,1.229 2.479,1.125 2.479,1.125 2.781,1.125 false 2.115,2.792 2.281,2.958 2.281,2.958 2.906,2.958 false 1.344,2.552 1.635,2.552 1.635,2.552 1.771,2.427 false 4.813,1.156 5.073,1.156 5.073,1.156 5.323,1.604 false 4.615,1.51 4.76,1.51 4.76,1.51 5.094,1.76 false 4.615,2.521 4.813,2.521 4.813,2.521 5.125,2.135 false 5.604,1.771 5.948,1.448 5.948,1.448 6.146,1.448 false 5.552,2.167 5.885,2.469 5.885,2.469 6.094,2.469 false 1.896,2.354 2.854,2.438 2.854,2.438 2.552,2.198 false 2.448,2.604 2.865,2.448 false 2.906,2.385 3.219,2.542 0.313,0.156 10 false *e 2.958,2.865 3.271,3.021 0.313,0.156 10 false *f 4.615,1.073 4.927,1.229 0.313,0.156 10 false *g 1.229,0.948 1.542,1.104 0.313,0.156 10 false *a 2.844,1.031 3.156,1.188 0.313,0.156 10 false *b 4.438,1.406 4.75,1.563 0.313,0.156 10 false *c 4.448,2.417 4.76,2.573 0.313,0.156 10 false *d 6.135,2.365 6.448,2.521 0.313,0.156 10 false *d 6.188,1.344 6.5,1.5 0.313,0.156 10 false *d 1.198,2.469 1.51,2.625 0.313,0.156 10 false A
*a Retard Side Path *b Advance Side Path
*c Open *d Close
*e Rubber Piece *f Vinyl Tape
*g Knock Pin - -


i.

Clean the camshaft journal with non-residue solvent.


ii.

Cover the 4 oil paths of the cam journal with vinyl tape as shown in the illustration.

HINT:

There are 4 oil paths in the grooves of the camshaft. Plug 3 of the paths with rubber pieces.



iii.

Make a hole at the port (A) shown in the illustration.


iv.
A196906

While applying approximately 200 kPa (2.0 kgf/ cm2, 29 psi) of air pressure to the oil path, forcibly turn the camshaft timing gear assembly in the advance direction (counterclockwise).

CAUTION:

Cover the paths with a piece of cloth when applying pressure to keep oil from spraying.


NOTICE:

Do not allow the camshaft timing gear assembly to lock. If it locks, release the lock pin again.


HINT:
·

Depending on the air pressure applied, the camshaft timing gear assembly may turn in the advance direction without assistance by hand.

·

If enough air pressure cannot be applied because of air leakage from the port, releasing the lock pin may be difficult.




v.

Remove the vinyl tape and rubber pieces from the camshaft.



f.

Remove the bolt and camshaft timing gear assembly.

NOTICE:

Do not allow the camshaft timing gear assembly to lock. If it locks, release the lock pin again.



Hide 13750 7.INSTALL VALVE LASH ADJUSTER ASSEMBLY

a.

Inspect the 16 valve lash adjuster assemblies before installing them.

Click hereEngine / Hybrid System>1AR-FE (ENGINE MECHANICAL)>ENGINE UNIT>INSPECTION


b.

Install the 16 valve lash adjuster assemblies to the cylinder head sub-assembly.

NOTICE:

Install each valve lash adjuster assembly to the same place it was removed from.



Hide 13801 8.INSTALL NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

a.
A196911C37
1.073,0.229 1.24,0.229 1.24,0.229 1.563,0.542 false 2.854,1.042 2.531,1.042 false 0.729,1.125 1.063,1.125 true 2.906,0.958 3.104,1.281 0.198,0.323 10 false *2 0.865,0.146 1.042,0.323 0.177,0.177 10 false *1 0.552,1.042 0.75,1.375 0.198,0.333 10 false *3
*1 No. 1 Valve Rocker Arm Sub-assembly
*2 Valve Lash Adjuster Assembly
*3 Valve Stem Cap


Apply engine oil to the valve lash adjuster assembly tips and valve stem caps.


b.

Install the 16 No. 1 valve rocker arm sub-assemblies as shown in the illustration.


Hide 11821 9.INSTALL NO. 2 CAMSHAFT BEARING

Hide 11811 10.INSTALL NO. 1 CAMSHAFT BEARING

Hide 15678A 11.INSTALL OIL CONTROL VALVE FILTER

Hide 13511 12.INSTALL CAMSHAFT

a.

Clean the camshaft journals, camshaft housing sub-assembly and camshaft bearing caps.


b.

Apply a light coat of engine oil to the camshaft journals, camshaft housing sub-assembly and camshaft bearing caps.


c.

Install the camshaft and No. 2 camshaft to the camshaft housing sub-assembly.

HINT:

Perform "Inspection After Repair" after replacing the camshaft or No. 2 camshaft.

Click hereEngine / Hybrid System>1AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



Hide 13.INSTALL CAMSHAFT BEARING CAP

a.
A286417

Confirm the marks and numbers on the No. 1 camshaft bearing cap, No. 2 camshaft bearing cap and 3 No. 3 camshaft bearing caps and place them in their proper positions and directions.


b.
A196885N14
0.063,0.719 0.167,0.865 0.104,0.146 10 false 9 1.521,1.615 1.615,1.771 0.094,0.156 10 true 1 1.552,0 1.646,0.177 0.094,0.177 10 false 2 2.135,1.635 2.25,1.781 0.115,0.146 10 true 3 2.104,0 2.198,0.156 0.094,0.156 10 false 4 0.938,1.615 1.052,1.76 0.115,0.146 10 true 5 0.969,0 1.083,0.156 0.115,0.156 10 false 6 2.708,1.625 2.833,1.781 0.125,0.156 10 true 7 2.698,0 2.792,0.146 0.094,0.146 10 false 8 0.01,0.083 0.188,0.229 0.177,0.146 10 false 10 0.292,1.927 0.552,2.073 0.26,0.146 10 true 11

Install the 11 bolts in the order shown in the illustration.

Torque:
16 N*m (163 kgf*cm, 12 ft.*lbf)

NOTICE:

Make sure that the camshaft and No. 2 camshaft rotate smoothly after installing the No. 1 camshaft bearing cap, No. 2 camshaft bearing cap and 3 No. 3 camshaft bearing caps.



Hide 11103 14.INSTALL CAMSHAFT HOUSING SUB-ASSEMBLY

a.
A186390C20
1.844,0.615 2.115,0.615 false 0.552,0.802 0.823,0.802 false 1.51,0.229 1.969,0.229 false 2,0.146 2.229,0.354 0.229,0.208 10 false *1 2.177,0.531 2.385,0.771 0.208,0.24 10 false *2 0.354,0.708 0.604,0.896 0.25,0.188 10 false *3 0.219,1.594 0.375,1.813 0.156,0.219 10 false *b 0.198,0 0.385,0.24 0.188,0.24 10 false *a
*1 No. 1 Valve Rocker Arm Sub-assembly
*2 Valve Stem Cap
*3 Valve Lash Adjuster Assembly
*a Incorrect
*b Correct


Check that the No. 1 valve rocker arm sub-assemblies are installed as shown in the illustration.


b.
A311889C05
0.792,1.167 0.792,0.927 false 0.781,0.135 1.094,0.333 0.313,0.198 10 false *a 0.729,1.198 1.042,1.396 0.313,0.198 10 false *b 1.417,0.813 3.406,1.01 1.99,0.198 10 false 2.5 to 3.5 mm 1.042,4.385 3.031,4.583 1.99,0.198 10 false 3.5 to 4.0 mm
*a Dashed Line
*b Groove


Apply seal packing in a continuous line as shown in the illustration.

Seal Packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Apply Seal Packing as Follows
Area Seal Packing Diameter Application Position
Continuous Line 3.0 to 4.0 mm (0.118 to 0.157 in.) Distance from edge of camshaft housing sub-assembly to center of seal packing: 3.5 to 4.0 mm (0.138 to 0.157 in.)
Dashed Line Distance from outside edge of groove to center of seal packing: 2.5 to 3.5 mm (0.0984 to 0.138 in.)

NOTICE:
·

Remove any oil from the contact surfaces.

·

Install the camshaft housing sub-assembly within 3 minutes and tighten the bolts within 10 minutes of applying seal packing.




c.
A196907C12
1.135,1.333 0.875,1.875 0.875,1.875 2.375,1.323 false 2.281,0.375 2.458,0.542 0.177,0.167 10 false *b 0.958,0.375 1.135,0.542 0.177,0.167 10 false *a 0.677,1.792 0.885,1.969 0.208,0.177 10 false *c
*a Approximately 17°
*b Approximately 2°
*c Knock Pin


Position the knock pins of the camshaft and No. 2 camshaft as shown in the illustration.


d.
A196884N11
1.094,0.115 1.198,0.26 0.104,0.146 10 false 9 1.865,0.615 1.958,0.771 0.094,0.156 10 true 1 1.552,1.833 1.646,2.01 0.094,0.177 10 true 2 1.563,0.115 1.677,0.26 0.115,0.146 10 false 3 2.354,0.625 2.448,0.781 0.094,0.156 10 true 4 2.073,1.844 2.188,1.99 0.115,0.146 10 true 5 2.042,0.115 2.156,0.271 0.115,0.156 10 false 6 1.354,0.635 1.479,0.792 0.125,0.156 10 true 7 1.031,1.844 1.125,1.99 0.094,0.146 10 true 8 2.948,0.865 3.125,1.01 0.177,0.146 10 false 10 2.281,1.917 2.458,2.063 0.177,0.146 10 true 20 0.771,1.896 0.948,2.042 0.177,0.146 10 false 19 3.135,0.625 3.313,0.771 0.177,0.146 10 false 18 3.125,1.708 3.302,1.854 0.177,0.146 10 false 17 3.146,1.052 3.323,1.198 0.177,0.146 10 false 16 0.74,0.115 0.917,0.26 0.177,0.146 10 false 15 0.24,1.948 0.417,2.094 0.177,0.146 10 false 14 0.146,0.646 0.323,0.792 0.177,0.146 10 false 13 2.469,0.115 2.646,0.26 0.177,0.146 10 false 12 2.552,1.865 2.729,2.01 0.177,0.146 10 false 11

Install the camshaft housing sub-assembly, and then install the 20 bolts in the order shown in the illustration.

Torque:
27 N*m (275 kgf*cm, 20 ft.*lbf)

NOTICE:
·

Do not apply oil for at least 2 hours after installation.

·

Do not start the engine for at least 2 hours after installation.

·

After installation, if the seal packing has seeped out, wipe it off.




Hide 13050 15.INSTALL CAMSHAFT TIMING GEAR ASSEMBLY

a.
A284102C12
0.781,1.313 0.958,1.313 0.958,1.313 1.771,0.844 false 2.802,1.49 2.615,1.49 2.615,1.49 2.042,1.135 false 0.615,1.219 0.927,1.375 0.313,0.156 10 false *a 2.833,1.427 3.146,1.583 0.313,0.156 10 false *b
*a Knock Pin Hole
*b Alignment Mark


Check the camshaft timing gear assembly position.

If the camshaft timing gear assembly is not set to the advanced position, release the lock pin and reset the camshaft timing gear assembly. (Refer to the "Set Camshaft Timing Gear Assembly" procedures.)


b.
A196901C56
1.854,0.625 1.635,0.906 false 1.156,0.167 0.698,0.75 false 1.188,0.063 1.365,0.24 0.177,0.177 10 false *b 1.875,0.521 2.042,0.698 0.167,0.177 10 false *a
*a Knock Pin
*b Pin Hole


Align and fit the knock pin of the camshaft with the pin hole of the camshaft timing gear assembly.


c.
A196904C75
2.146,0.854 1.896,0.854 1.896,0.854 1.5,1.073 false 0.813,0.771 0.906,0.771 0.906,0.771 1.115,0.99 false 0.615,0.688 0.792,0.844 0.177,0.156 10 false *1 1.802,0.531 2,0.698 0.198,0.167 10 false *c 2.188,0.771 2.365,0.938 0.177,0.167 10 false *2 1.74,2.021 1.938,2.177 0.198,0.156 10 false *d 0.063,0.042 0.25,0.208 0.188,0.167 10 false *a 0.063,1.833 0.26,2 0.198,0.167 10 false *b
*1 Camshaft Timing Gear Assembly
*2 Camshaft Flange
*a Incorrect
*b Correct
*c Gap
*d No Gap


Check that there is no gap between the camshaft timing gear assembly and camshaft flange.


d.
A265379C12
1.469,0.225 1.648,0.382 0.178,0.157 10 *a 0.04,1.421 0.219,1.578 0.178,0.157 10 *b
*a Hold
*b Turn


Using a wrench to hold the hexagonal portion of the camshaft, install the bolt.

Torque:
85 N*m (867 kgf*cm, 63 ft.*lbf)

NOTICE:
·

Be careful not to damage the cylinder head sub-assembly or spark plug tube with the wrench.

·

Do not disassemble the camshaft timing gear assembly.



HINT:

Perform "Inspection After Repair" after replacing the camshaft timing gear assembly.

Click hereEngine / Hybrid System>1AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



Hide 13070A 16.INSTALL CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

a.
A196902C27
1.719,0.646 1.615,0.938 false 1.229,0.219 0.677,0.781 false 1.771,0.552 1.958,0.719 0.188,0.167 10 false *a 1.281,0.104 1.448,0.271 0.167,0.167 10 false *b
*a Knock Pin
*b Pin Hole


Align and fit the knock pin of the No. 2 camshaft with the pin hole of the camshaft timing exhaust gear assembly.


b.
A196904C76
2.146,0.865 1.896,0.865 1.896,0.865 1.5,1.083 false 0.823,0.76 0.917,0.76 0.917,0.76 1.125,0.979 false 0.604,0.667 0.781,0.823 0.177,0.156 10 false *1 1.802,0.531 2,0.698 0.198,0.167 10 false *c 2.188,0.771 2.365,0.938 0.177,0.167 10 false *2 1.74,2.021 1.938,2.177 0.198,0.156 10 false *d 0.063,0.042 0.25,0.208 0.188,0.167 10 false *a 0.063,1.833 0.26,2 0.198,0.167 10 false *b
*1 Camshaft Timing Exhaust Gear Assembly
*2 No. 2 Camshaft Flange
*a Incorrect
*b Correct
*c Gap
*d No Gap


Check that there is no gap between the camshaft timing exhaust gear assembly and No. 2 camshaft flange.


c.
A265378C12
1.602,0.298 1.765,0.45 0.163,0.152 10 *a 0.305,1.902 0.468,2.054 0.163,0.152 10 *b
*a Hold
*b Turn


Using a wrench to hold the hexagonal portion of the No. 2 camshaft, install the bolt.

Torque:
85 N*m (867 kgf*cm, 63 ft.*lbf)

NOTICE:
·

Be careful not to damage the cylinder head sub-assembly or spark plug tube with the wrench.

·

Do not disassemble the camshaft timing exhaust gear assembly.



HINT:

Perform "Inspection After Repair" after replacing the camshaft timing exhaust gear assembly.

Click hereEngine / Hybrid System>1AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



Hide 17.ADD ENGINE OIL

a.
A198199

Add 50 cc (3.1 cu.in.) of engine oil into the oil hole shown in the illustration.

NOTICE:
·

Engine oil must be added if the lash adjusters were removed.

·

Make sure that the low pressure chamber and oil paths of the lash adjusters are full of engine oil.




Hide 18.SET NO. 1 CYLINDER TO TDC/COMPRESSION

a.
A260711N04
1.313,0.229 1.573,0.385 0.26,0.156 10 true 40°

Temporarily install the crankshaft pulley bolt.


b.

Rotate the crankshaft 40° counterclockwise to position the crankshaft pulley key as shown in the illustration.


c.
A293511C09
0.448,2.865 0.781,3.104 true 1.792,2.823 2.615,3.104 true 2.469,1.042 2.573,0.479 2.573,0.479 2.76,0.479 true 1.042,1.021 0.906,0.458 0.906,0.458 1.083,0.458 true 0.292,2.771 0.604,2.927 0.313,0.156 10 false *c 2.823,0.385 3.135,0.542 0.313,0.156 10 false *b 1.615,2.708 1.927,2.865 0.313,0.156 10 false *c 1.156,0.365 1.469,0.521 0.313,0.156 10 false *a 3.021,3.677 3.219,3.854 0.198,0.177 10 false A 1.354,3.563 1.552,3.74 0.198,0.177 10 false A
*a Approximately 7°
*b Approximately 32°
*c Timing Mark


Check that the timing marks of the camshaft timing exhaust gear assembly and camshaft timing gear assembly are as shown in the illustration.

HINT:

"A" is not a timing mark.



Hide 13561 19.INSTALL NO. 1 CHAIN VIBRATION DAMPER

a.
A196868N02
1.656,0.406 1.781,0.583 0.125,0.177 10 true 1 2.438,1.594 2.563,1.771 0.125,0.177 10 true 2

Install the No. 1 chain vibration damper with the 2 bolts in the order shown in the illustration.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 13506 20.INSTALL CHAIN SUB-ASSEMBLY

a.

Place the chain sub-assembly onto the camshaft timing exhaust gear assembly and camshaft timing gear assembly and crankshaft timing sprocket.

HINT:
·

Make sure the mark plate of the chain sub-assembly faces away from the engine.

·

It is not necessary to install the chain sub-assembly to the teeth of the gears and sprocket.




b.
A196871C11
2.635,0.26 2.5,0.26 2.5,0.26 2.135,0.729 true 1.677,1.365 1.823,1.365 1.823,1.365 2.063,1.167 true 2.667,0.146 2.823,0.302 0.156,0.156 10 false *a 1.49,1.271 1.667,1.438 0.177,0.167 10 false *b
*a Mark Plate
*b Timing Mark


Align the mark plate (yellow or gold) of the chain sub-assembly with the timing mark of the camshaft timing exhaust gear assembly and install the chain sub-assembly to the camshaft timing exhaust gear assembly.


c.
A196872C18
0.906,1.021 1.083,1.021 1.083,1.021 1.292,1.26 true 1.865,0.229 1.708,0.229 1.708,0.229 1.521,1.229 true 1.917,0.115 2.083,0.281 0.167,0.167 10 false *b 0.729,0.927 0.885,1.104 0.156,0.177 10 false *a
*a Mark Plate
*b Timing Mark


Align the mark plate (pink or gold) of the chain sub-assembly with the timing mark of the crankshaft timing sprocket and install the chain sub-assembly to the crankshaft timing sprocket.


d.
A196873

Tie a string above the crankshaft timing sprocket so that the chain sub-assembly is secure.


e.
A196874C11
1.365,3.135 0.906,3.604 true 1.646,3.615 0.844,3.854 true 1.385,3.031 1.563,3.198 0.177,0.167 10 true *a 1.667,3.51 1.854,3.698 0.188,0.188 10 true *b
*a Mark Plate
*b Timing Mark


Using a wrench, hold the hexagonal portion of the camshaft and rotate the camshaft counterclockwise to align the timing mark of the camshaft timing gear assembly with the mark plate (yellow or gold) of the chain sub-assembly, and install the chain sub-assembly to the camshaft timing gear assembly.

HINT:

Hold the camshaft in place with a wrench until the No. 1 chain tensioner assembly is installed.



f.
A196875

Remove the string above the crankshaft timing sprocket, rotate the crankshaft clockwise, and loosen the chain sub-assembly so that the chain tensioner slipper can be installed.

NOTICE:

Make sure the chain sub-assembly is secure.



Hide 13559 21.INSTALL CHAIN TENSIONER SLIPPER

a.

Install the chain tensioner slipper with the bolt.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 13540 22.INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY

a.

Install a new gasket and the No. 1 chain tensioner assembly with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Remove the pin from the stopper plate.


Hide 13566B 23.INSTALL TIMING CHAIN GUIDE

a.

Install the timing chain guide with the bolt.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 24.SET NO. 1 CYLINDER TO TDC/COMPRESSION

a.

Temporarily install the crankshaft pulley bolt.

A292247C17
5.969,2.917 6.219,2.771 false 3.51,5.708 4.646,5.438 false 1.021,2.833 1.031,3.021 false 0.958,0.354 1.271,0.51 0.313,0.156 10 false *a 6.25,0.448 6.563,0.604 0.313,0.156 10 false *b 5.792,2.875 6.104,3.031 0.313,0.156 10 false *c 4.708,5.323 5.021,5.479 0.313,0.156 10 false *1 0.969,3.042 1.281,3.198 0.313,0.156 10 false *c 6.688,3.656 6.844,3.854 0.156,0.198 10 false A 1.646,2.719 1.802,2.917 0.156,0.198 10 false A
*1 Crankshaft Pulley Key - -
*a Approximately 7° *b Approximately 32°
*c Timing Mark - -



b.

Rotate the crankshaft clockwise and align the crankshaft pulley key as shown in the illustration.


c.

Check that the timing marks on the camshaft timing gear assembly and camshaft timing exhaust gear assembly are as shown in the illustration.

HINT:

"A" is not a timing mark.



Hide 23814B 26.INSTALL FUEL DELIVERY PIPE

Hide 44774 27.CONNECT UNION TO VACUUM TUBE HOSE

Hide 12262 28.CONNECT NO. 2 VENTILATION HOSE

Hide 17650 29.INSTALL VACUUM SWITCHING VALVE ASSEMBLY (for ACIS)

Hide 22030 30.INSTALL THROTTLE BODY WITH MOTOR ASSEMBLY

Hide 25051 31.INSTALL EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (TWC: Front Catalyst)

Hide 17167 32.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

Hide 11310 35.INSTALL TIMING CHAIN COVER SUB-ASSEMBLY