Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › REAR DOOR WINDOW FRAME MOULDING
RM3160E _59 Vehicle Exterior _019724 EXTERIOR PANELS / TRIM _0109643 REAR DOOR WINDOW FRAME MOULDING A

EXTERIOR PANELS / TRIM  REAR DOOR WINDOW FRAME MOULDING  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.


·

The following procedure is for the LH side.



PROCEDURE

Hide 75740 1.REMOVE REAR DOOR BELT MOULDING ASSEMBLY

Hide 67872 2.DISCONNECT REAR DOOR WEATHERSTRIP

a.
B365195

Disengage the 2 clips and disconnect the rear door weatherstrip.


Hide 75762A 3.REMOVE REAR DOOR FRONT WINDOW FRAME MOULDING

HINT:

When removing the rear door front window frame moulding, heat the vehicle body and rear door front window frame moulding using a heat light.


Heating Temperature
Item Temperature
Vehicle Body 40 to 60°C (104 to 140°F)
Rear Door Front Window Frame Moulding 20 to 30°C (68 to 86°F)

NOTICE:

Do not heat the vehicle body or rear door front window frame moulding excessively.


a.

Using a heat light, heat the rear door front window frame moulding.


b.
B363128
0.958,1.146 1.406,1.594 true 1.771,1.531 2.219,1.979 true 1.656,1.938 2.104,2.385 true 0.781,1.063 1.094,1.219 0.313,0.156 10 false *a 2.156,2.323 2.469,2.479 0.313,0.156 10 false *b 2.24,1.917 2.552,2.073 0.313,0.156 10 false *a
*a Double-sided Tape
*b Caulking Sponge


Using a moulding remover, disengage the clip and guide, and separate the double-sided tape and caulking sponge to remove the rear door front window frame moulding.


Hide 75766A 4.REMOVE REAR DOOR REAR WINDOW FRAME MOULDING

HINT:

When removing the rear door rear window frame moulding, heat the vehicle body and rear door rear window frame moulding using a heat light.


Heating Temperature
Item Temperature
Vehicle Body 40 to 60°C (104 to 140°F)
Rear Door Rear Window Frame Moulding 20 to 30°C (68 to 86°F)

NOTICE:

Do not heat the vehicle body or rear door rear window frame moulding excessively.


a.

Using a heat light, heat the rear door rear window frame moulding.


b.
B363130
0.865,1.406 1.51,1.052 true 1.844,1.385 2.313,1.146 true 1.75,0.365 2.219,0.125 true 0.688,1.333 1,1.49 0.313,0.156 10 false *a 2.26,0.042 2.573,0.198 0.313,0.156 10 false *a 2.344,1.042 2.656,1.198 0.313,0.156 10 false *a
*a Double-sided Tape


Using a moulding remover, disengage the 3 clips and separate the double-sided tape to remove the rear door rear window frame moulding.


Hide 75764A 5.REMOVE REAR DOOR UPPER WINDOW FRAME MOULDING

a.

Insert a 4.0 mm (0.157 in.) drill bit into a drill.


b.

Tape the 4.0 mm (0.157 in.) drill bit 5.0 mm (0.197 in.) from the tip as shown in the illustration.

B363132
1.823,1.885 2.073,2.094 0.25,0.208 10 false A

Reference Measurement:
Area Measurement Area Measurement
A 5.0 mm (0.197 in.) - -


NOTICE:

Tape the 4.0 mm (0.157 in.) drill bit to prevent the drill bit from going too deep.



c.

Lightly press the drill bit against the rivets to drill off the rivet flanges, and remove the 5 rivets.

NOTICE:
·

Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.

·

Prying the rivets with the drill may damage the rivet installation holes or drill bit.

·

Be careful of the drilled rivets, as they may be hot.




d.

Using a vacuum cleaner, remove the rivet fragments and shavings from the drilled areas.


e.

Disengage the guide to remove the rear door upper window frame moulding.


Hide 75744 6.REMOVE REAR DOOR REAR UPPER OUTSIDE MOULDING

a.

Insert a 4.0 mm (0.157 in.) drill bit into a drill.


b.

Tape the 4.0 mm (0.157 in.) drill bit 5.0 mm (0.197 in.) from the tip as shown in the illustration.

B363134
3.385,0.677 3.542,0.875 0.156,0.198 10 false A

Reference Measurement:
Area Measurement Area Measurement
A 5.0 mm (0.197 in.) - -


NOTICE:

Tape the 4.0 mm (0.157 in.) drill bit to prevent the drill bit from going too deep.



c.

Lightly press the drill bit against the rivets to drill off the rivet flanges, and remove the 3 rivets and rear door rear upper outside moulding.

NOTICE:
·

Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.

·

Prying the rivets with the drill may damage the rivet installation holes or drill bit.

·

Be careful of the drilled rivets, as they may be hot.




d.

Using a vacuum cleaner, remove the rivet fragments and shavings from the drilled areas.