Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › ROOF DRIP SIDE FINISH MOULDING
RM3160E _59 Vehicle Exterior _019724 EXTERIOR PANELS / TRIM _0109647 ROOF DRIP SIDE FINISH MOULDING A

EXTERIOR PANELS / TRIM  ROOF DRIP SIDE FINISH MOULDING  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 75597 1.REMOVE ROOF DRIP SIDE FINISH MOULDING JOINT COVER (w/o Roof Rack)

a.
B362645
2.104,0.385 2.292,0.573 0.188,0.188 10 true 1 1.26,0.406 1.448,0.594 0.188,0.188 10 true 2
V100155

Protective Tape


Apply protective tape around the roof drip side finish moulding joint cover as shown in the illustration.


b.

Disengage the 2 clips and 2 claws, and remove the 2 roof drip side finish moulding joint covers as indicated by the arrows, in the order shown in the illustration.


Hide 63470B 2.REMOVE ROOF RACK ASSEMBLY (w/ Roof Rack)

Hide 75552 3.REMOVE FRONT ROOF DRIP SIDE FINISH MOULDING (w/o Roof Rack)

HINT:

When removing the front roof drip side finish moulding, heat the vehicle body and front roof drip side finish moulding using a heat light.


Heating Temperature
Item Temperature
Vehicle Body 40 to 60°C (104 to 140°F)
Front Roof Drip Side Finish Moulding 20 to 30°C (68 to 86°F)

NOTICE:

Do not heat the vehicle body or front roof drip side finish moulding excessively.


a.

Using a heat light, heat the front roof drip side finish moulding.


b.
B362647
0,0 0,0 false
V100155

Protective Tape


Apply protective tape around the front roof drip side finish moulding.


c.

Using a moulding remover, disengage the roof drip side finish moulding clip and remove the front roof drip side finish moulding.

NOTICE:
·

Do not remove the roof drip side finish moulding clip.

·

If the roof drip side finish moulding clip is damaged or falls out, replace it with a new one.




Hide 75552 4.REMOVE FRONT ROOF DRIP SIDE FINISH MOULDING (w/ Roof Rack)

HINT:

When removing the front roof drip side finish moulding, heat the vehicle body and front roof drip side finish moulding using a heat light.


Heating Temperature
Item Temperature
Vehicle Body 40 to 60°C (104 to 140°F)
Front Roof Drip Side Finish Moulding 20 to 30°C (68 to 86°F)

NOTICE:

Do not heat the vehicle body or front roof drip side finish moulding excessively.


a.

Using a heat light, heat the front roof drip side finish moulding.


b.
B362643
0,0 0,0 false
V100155

Protective Tape


Apply protective tape around the front roof drip side finish moulding.


c.

Using a moulding remover, disengage the roof drip side finish moulding clip and remove the front roof drip side finish moulding.

NOTICE:
·

Do not remove the roof drip side finish moulding clip.

·

If the roof drip side finish moulding clip is damaged or falls out, replace it with a new one.




Hide 75556C 5.REMOVE CENTER ROOF DRIP SIDE FINISH MOULDING (w/o Roof Rack)

HINT:

When removing the center roof drip side finish moulding, heat the vehicle body and center roof drip side finish moulding using a heat light.


Heating Temperature
Item Temperature
Vehicle Body 40 to 60°C (104 to 140°F)
Center Roof Drip Side Finish Moulding 20 to 30°C (68 to 86°F)

NOTICE:

Do not heat the vehicle body or center roof drip side finish moulding excessively.


a.

Using a heat light, heat the center roof drip side finish moulding.


b.
B362646
0.813,0.385 1.188,0.26 false 1.229,0.188 1.542,0.344 0.313,0.156 10 false *a
*a Matchmark
V100155

Protective Tape


Apply protective tape around the center roof drip side finish moulding.


c.

Place a matchmark on the vehicle body at the location indicated in the illustration.


d.

Using a moulding remover, disengage the roof drip side finish moulding clip and remove the center roof drip side finish moulding.

NOTICE:
·

Do not remove the roof drip side finish moulding clip.

·

If the roof drip side finish moulding clip is damaged or falls out, replace it with a new one.




Hide 75554 6.REMOVE REAR ROOF DRIP SIDE FINISH MOULDING (w/o Roof Rack)

HINT:

When removing the rear roof drip side finish moulding, heat the vehicle body and rear roof drip side finish moulding using a heat light.


Heating Temperature
Item Temperature
Vehicle Body 40 to 60°C (104 to 140°F)
Rear Roof Drip Side Finish Moulding 20 to 30°C (68 to 86°F)

NOTICE:

Do not heat the vehicle body or rear roof drip side finish moulding excessively.


a.

Using a heat light, heat the rear roof drip side finish moulding.


b.
B362648
0,0 0,0 false
V100155

Protective Tape


Apply protective tape around the rear roof drip side finish moulding.


c.

Using a moulding remover, disengage the roof drip side finish moulding clip and remove the rear roof drip side finish moulding.

NOTICE:
·

Do not remove the roof drip side finish moulding clip.

·

If the roof drip side finish moulding clip is damaged or falls out, replace it with a new one.




Hide 75554 7.REMOVE REAR ROOF DRIP SIDE FINISH MOULDING (w/ Roof Rack)

HINT:

When removing the rear roof drip side finish moulding, heat the vehicle body and rear roof drip side finish moulding using a heat light.


Heating Temperature
Item Temperature
Vehicle Body 40 to 60°C (104 to 140°F)
Rear Roof Drip Side Finish Moulding 20 to 30°C (68 to 86°F)

NOTICE:

Do not heat the vehicle body or rear roof drip side finish moulding excessively.


a.

Using a heat light, heat the rear roof drip side finish moulding.


b.
B362644
0,0 0,0 false
V100155

Protective Tape


Apply protective tape around the rear roof drip side finish moulding.


c.

Using a moulding remover, disengage the roof drip side finish moulding clip and remove the rear roof drip side finish moulding.

NOTICE:
·

Do not remove the roof drip side finish moulding clip.

·

If the roof drip side finish moulding clip is damaged or falls out, replace it with a new one.