Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › ROOF DRIP SIDE FINISH MOULDING
RM3160E _59 Vehicle Exterior _019724 EXTERIOR PANELS / TRIM _0109647 ROOF DRIP SIDE FINISH MOULDING A

EXTERIOR PANELS / TRIM  ROOF DRIP SIDE FINISH MOULDING  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 75561A 1.INSTALL ROOF DRIP SIDE FINISH MOULDING CLIP

NOTICE:

When installing new roof drip side finish moulding clips, remove any double-sided tape remaining where the roof drip side finish moulding clips will be installed on the vehicle body and clean the vehicle body with a non-residue solvent.


a.
B362651
0.813,0.833 1.281,0.833 1.281,0.833 1.615,1.135 true 2.135,0.313 2.583,0.313 false 1.938,0.219 2.25,0.375 0.313,0.156 10 false *a 0.625,0.75 0.938,0.906 0.313,0.156 10 false *b
*a Adhesive
*b 2 to 3 mm Bead of Adhesive


Apply a 2 to 3 mm (0.0787 to 0.118 in.) bead of adhesive (3M DP-105 or equivalent) to each new roof drip side finish moulding clip.

HINT:

Adhesive strength (tensile strength): 13.7 MPa (140.0 kgf/cm2, 1987 psi) or more (when the temperature is 23°C (73°F).)



b.

Install the roof drip side finish moulding clips to the positions on the roof panel shown in the illustration. Determine the locations and firmly press and install the roof drip side finish moulding clips after lightly applying adhesive.

B362650
0.417,0.844 0.417,0.292 0.417,0.292 1.365,0.292 false 1.021,0.635 1.021,0.292 false 4.51,0.698 4.51,0.333 4.51,0.333 5.458,0.333 false 5.208,0.677 5.208,0.333 false 4.094,2.948 4.094,2.719 4.094,2.719 5.042,2.719 false 4.74,2.958 4.74,2.719 false 0.563,1.188 0.719,1.385 0.156,0.198 10 false A 1.125,1.01 1.281,1.208 0.156,0.198 10 false B 2.104,0.365 2.26,0.563 0.156,0.198 10 false C 2.76,0.438 2.917,0.635 0.156,0.198 10 false D 4.51,1.052 4.667,1.25 0.156,0.198 10 false E 5.167,1.052 5.323,1.25 0.156,0.198 10 false F 6.063,0.292 6.219,0.49 0.156,0.198 10 false G 6.698,0.323 6.854,0.521 0.156,0.198 10 false H 4.083,3.323 4.24,3.521 0.156,0.198 10 false I 4.677,3.344 4.833,3.542 0.156,0.198 10 false J 5.656,2.51 5.813,2.708 0.156,0.198 10 false K 6.229,2.521 6.385,2.719 0.156,0.198 10 false L 1.406,0.219 1.719,0.375 0.313,0.156 10 false *a 5.5,0.271 5.813,0.427 0.313,0.156 10 false *a 5.083,2.635 5.396,2.792 0.313,0.156 10 false *a 4.083,2.417 4.406,2.646 0.323,0.229 12 false *A
*A w/o Roof Rack - -
*a Protruding Part - -


Standard Measurement:
Area Measurement Area Measurement
A 2.5 to 3.5 mm (0.0985 to 0.138 in.) B 2.5 to 3.5 mm (0.0985 to 0.138 in.)
C 5.3 to 6.3 mm (0.209 to 0.248 in.) D 8.6 mm (0.339 in.)
E 2.5 to 3.5 mm (0.0985 to 0.138 in.) F 2.5 to 3.5 mm (0.0985 to 0.138 in.)
G 5.2 to 6.2 mm (0.205 to 0.244 in.) H 10.2 mm (0.402 in.)
I 2.5 to 3.5 mm (0.0985 to 0.138 in.) J 2.5 to 3.5 mm (0.0985 to 0.138 in.)
K 6.6 to 7.6 mm (0.260 to 0.299 in.) L 7.1 mm (0.280 in.)



c.

Install the roof drip side finish moulding when 20 minutes or more have elapsed after pressing and installing the roof drip side finish moulding clips.

HINT:
·

Initial hardening time: 20 minutes

·

Complete hardening time: 48 hours




Hide 75554 2.INSTALL REAR ROOF DRIP SIDE FINISH MOULDING (w/o Roof Rack)

a.
B365110

Engage the roof drip side finish moulding clip and install the rear roof drip side finish moulding.


Hide 75554 3.INSTALL REAR ROOF DRIP SIDE FINISH MOULDING (w/ Roof Rack)

a.
B365111

Engage the roof drip side finish moulding clip and install the rear roof drip side finish moulding.


Hide 75556C 4.INSTALL CENTER ROOF DRIP SIDE FINISH MOULDING (w/o Roof Rack)

a.
B365109
0.813,0.385 1.135,0.385 false 1.167,0.313 1.479,0.469 0.313,0.156 10 false *a
*a Matchmark


Position the center roof drip side finish moulding by aligning it with the matchmark on the vehicle body as shown in the illustration.


b.

Engage the roof drip side finish moulding clip and install the center roof drip side finish moulding as shown in the illustration.


Hide 75552 5.INSTALL FRONT ROOF DRIP SIDE FINISH MOULDING (w/o Roof Rack)

a.
B365107

Engage the roof drip side finish moulding clip and install the front roof drip side finish moulding.


Hide 75552 6.INSTALL FRONT ROOF DRIP SIDE FINISH MOULDING (w/ Roof Rack)

a.
B365108

Engage the roof drip side finish moulding clip and install the front roof drip side finish moulding.


Hide 75597 7.INSTALL ROOF DRIP SIDE FINISH MOULDING JOINT COVER (w/o Roof Rack)

a.
B362649
1.823,0.875 1.958,0.385 1.958,0.385 2.188,0.385 false 2.24,0.302 2.438,0.479 0.198,0.177 10 true *a 1.771,1.073 2.083,1.229 0.313,0.156 10 false *b
*a Mark
*b Outside of the Vehicle


Engage the 2 claws and 2 clips to install the 2 roof drip side finish moulding joint covers as shown in the illustration.


Hide 63470B 8.INSTALL ROOF RACK ASSEMBLY (w/ Roof Rack)