Home › Drivetrain › U660E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM › 2013.12–2016.11
RM3160E _52 Drivetrain _019725 U660E AUTOMATIC TRANSMISSION / TRANSAXLE _0109807 AUTOMATIC TRANSAXLE SYSTEM J

U660E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  ECU Power Source Circuit  


DESCRIPTION

When the ignition switch is turned to ON, voltage from the ECM's MREL terminal is applied to the EFI MAIN relay. This causes the contacts of the EFI MAIN relay to close, which supplies power to terminal +B of the TCM.

WIRING DIAGRAM

C301538
6.208,4.802 6.521,5 0.313,0.198 10 false C3 6.208,4.979 6.667,5.177 0.458,0.198 10 false TCM 6.052,3.563 6.365,3.76 0.313,0.198 10 false E1 5.854,3.438 6.01,3.635 0.156,0.198 10 false 8 6.031,1.375 6.344,1.573 0.313,0.198 10 false +B 4.594,1.375 4.906,1.573 0.313,0.198 10 false 1G 4.656,1.198 4.813,1.396 0.156,0.198 10 false 2 4.594,1.813 4.906,2.01 0.313,0.198 10 false 1G 4.646,1.646 4.802,1.844 0.156,0.198 10 false 6 5.344,1.813 6.26,2.01 0.917,0.198 10 false to ECM 1.969,3.208 4.365,3.604 2.396,0.396 10 false Semiconductor Power Integration Relay 2.948,2.063 4.177,2.26 1.229,0.198 10 false EFI MAIN 3.698,1.521 4.927,1.719 1.229,0.198 10 false EFI NO.2 2.115,1.531 3.344,1.729 1.229,0.198 10 false EFI-MAIN 1.583,1.375 1.896,1.573 0.313,0.198 10 false 1H 1.635,1.188 1.792,1.385 0.156,0.198 10 false 1 0.438,3.698 1.51,3.896 1.073,0.198 10 false FL MAIN 0.594,4.74 1.667,4.938 1.073,0.198 10 false Battery 5.792,1.281 6.104,1.479 0.313,0.198 10 false 18

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (TCM - BODY GROUND)
a.
C189544
1.552,0.906 1.979,1.188 0.427,0.281 1.031,2.177 0.417,2.938 false 0.167,0.146 0.396,0.344 0.229,0.198 10 false *a 1.698,0.958 1.979,1.115 0.281,0.156 10 false C3 0.292,2.969 0.49,3.125 0.198,0.156 10 false E1
*a Front view of wire harness connector
(to TCM)


Disconnect the TCM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C3-8 (E1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

2.INSPECT ECU TERMINAL VOLTAGE (+B TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT ECU TERMINAL VOLTAGE (+B TERMINAL)
a.
C189544
1.531,0.896 2.021,1.198 0.49,0.302 1.125,2.354 0.865,2.885 false 0.49,0.438 0.708,0.646 0.219,0.208 10 false *a 1.698,0.969 1.979,1.125 0.281,0.156 10 false C3 0.708,2.927 1.198,3.073 0.49,0.146 10 false +B
*a Front view of wire harness connector
(to TCM)


Disconnect the TCM connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C3-18 (+B) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

3.CHECK HARNESS AND CONNECTOR (TCM - NO. 1 INTEGRATION RELAY)
3.CHECK HARNESS AND CONNECTOR (TCM - NO. 1 INTEGRATION RELAY)
a.

Remove the No. 1 integration relay from the engine room relay block and junction block assembly.


b.

Disconnect the integration relay connector.


c.

Disconnect the TCM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
C3-18 (+B) - 1G-2 (+B) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
C3-18 (+B) or 1G-2 (+B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

GO TO ECM POWER SOURCE CIRCUIT (ENGINE CONTROL SYSTEM / SFI SYSTEM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR