Home › Engine / Hybrid System › 2GR-FE ENGINE CONTROL › SFI SYSTEM › 2013.12–2016.11
RM3160E _51 Engine / Hybrid System _019662 2GR-FE ENGINE CONTROL _0101052 SFI SYSTEM J

2GR-FE ENGINE CONTROL  SFI SYSTEM  ECM Power Source Circuit  


DESCRIPTION

When the ignition switch is turned to ON, battery voltage is applied to the IGSW terminal of the ECM. The output signal from the MREL terminal of the ECM causes current to flow to the coil of the semiconductor pwr integration ECU (EFI MAIN relay), closing the contacts of the EFI MAIN relay and supplying power to terminals +B and +B2 of the ECM.

WIRING DIAGRAM

A315018E04
0.917,0.969 2.771,1.198 1.854,0.229 10 false Ignition Switch Assembly*1 0.917,0.813 1.313,1.01 0.396,0.198 10 false F50 1.219,0.344 1.615,0.542 0.396,0.198 10 false AM2 2,0.333 2.396,0.531 0.396,0.198 10 false IG2 1.021,0.344 1.417,0.542 0.396,0.198 10 false 4 2.323,0.333 2.719,0.531 0.396,0.198 10 false 3 0.385,1.208 1.219,1.49 0.833,0.281 10 false ST 5.833,0.469 6.365,0.729 0.531,0.26 10 false IG1D 5.625,0.333 6.021,0.531 0.396,0.198 10 false 3 5.302,0.75 5.698,0.948 0.396,0.198 10 false F10 5.302,0.927 7.094,1.333 1.792,0.406 10 false Certification ECU (Smart Key ECU Assembly)*2 1.813,2.125 2.646,2.406 0.833,0.281 10 false IG2-MAIN 1.833,3.458 2.958,3.719 1.125,0.26 10 false EFI-MAIN 0.396,3.833 1.229,4.115 0.833,0.281 10 false FL MAIN 0.521,4.417 1.354,4.698 0.833,0.281 10 false Battery 1.083,1.969 1.406,2.229 0.323,0.26 10 false 1H 3.406,1.667 3.729,1.927 0.323,0.26 10 false 1E 4.313,1.969 4.635,2.229 0.323,0.26 10 false 1G 4.302,2.833 4.625,3.094 0.323,0.26 10 false 1G 4.313,3.292 4.635,3.552 0.323,0.26 10 false 1G 4.313,3.719 4.635,3.979 0.323,0.26 10 false 1G 2.813,2.646 3.646,2.927 0.833,0.281 10 false IG2 2.594,4.021 3.427,4.302 0.833,0.281 10 false EFI MAIN 1.125,1.792 1.521,1.99 0.396,0.198 10 false 1 3.354,1.469 3.75,1.667 0.396,0.198 10 false 1 4.354,1.792 4.75,1.99 0.396,0.198 10 false 4 4.344,2.646 4.74,2.844 0.396,0.198 10 false 1 4.354,3.115 4.75,3.313 0.396,0.198 10 false 2 4.354,3.542 4.75,3.74 0.396,0.198 10 false 6 3.552,2.125 4.094,2.313 0.542,0.188 10 false IG2-EFI 3.281,3.448 3.979,3.76 0.698,0.313 10 false EFI NO. 2 1.698,4.49 3.969,4.813 2.271,0.323 10 false Semiconductor Pwr Integration ECU 3.5,5.083 6.094,5.313 2.594,0.229 10 false *1: w/o Smart Entry and Start System 3.5,5.417 6.031,5.698 2.531,0.281 10 false *2: w/ Smart Entry and Start System 5.49,1.979 5.813,2.24 0.323,0.26 10 false A43 5.49,2.375 5.813,2.635 0.323,0.26 10 false A43 5.49,2.844 5.813,3.104 0.323,0.26 10 false A43 5.49,3.729 5.813,3.99 0.323,0.26 10 false A43 5.521,4.26 5.844,4.521 0.323,0.26 10 false C1 5.531,4.073 5.927,4.271 0.396,0.198 10 false 49 5.531,3.542 5.927,3.74 0.396,0.198 10 false 46 5.563,2.667 5.958,2.865 0.396,0.198 10 false 3 5.563,2.198 5.958,2.396 0.396,0.198 10 false 2 5.531,1.781 5.927,1.979 0.396,0.198 10 false 32 5.833,1.865 6.365,2.125 0.531,0.26 10 false IGSW 5.844,2.375 6.375,2.635 0.531,0.26 10 false +B 5.844,2.844 6.375,3.104 0.531,0.26 10 false +B2 5.833,3.729 6.365,3.99 0.531,0.26 10 false MREL 5.854,4.26 6.385,4.521 0.531,0.26 10 false E1 6.167,4.667 6.698,4.927 0.531,0.26 10 false ECM 0.344,1.667 0.552,1.854 0.208,0.188 10 false *1 3.698,0.333 3.906,0.521 0.208,0.188 10 false *1 4.365,0.333 4.573,0.521 0.208,0.188 10 false *2

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (SEMICONDUCTOR PWR INTEGRATION ECU VOLTAGE)
a.

Disconnect the semiconductor pwr integration ECU connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
1E-1 - Body ground Ignition switch ON 11 to 14 V



Result:
Result Proceed to
OK A
NG (w/o Smart Entry and Start System) B
NG (w/ Smart Entry and Start System) C



A

2.CHECK HARNESS AND CONNECTOR (BATTERY - SEMICONDUCTOR PWR INTEGRATION ECU)

B

6.CHECK HARNESS AND CONNECTOR (BATTERY - IGNITION SWITCH ASSEMBLY)

C

8.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - SEMICONDUCTOR PWR INTEGRATION ECU)
2.CHECK HARNESS AND CONNECTOR (BATTERY - SEMICONDUCTOR PWR INTEGRATION ECU)
a.

Disconnect the semiconductor pwr integration ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
1H-1 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.INSPECT SEMICONDUCTOR PWR INTEGRATION ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT SEMICONDUCTOR PWR INTEGRATION ECU
a.

Inspect the semiconductor pwr integration ECU.

Click herePower Source / Network>POWER DISTRIBUTION>INTEGRATION RELAY>INSPECTION


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (SEMICONDUCTOR PWR INTEGRATION ECU - ECM)

NG

REPLACE SEMICONDUCTOR PWR INTEGRATION ECU

4.CHECK HARNESS AND CONNECTOR (SEMICONDUCTOR PWR INTEGRATION ECU - ECM)
a.

Disconnect the semiconductor pwr integration ECU connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1G-4 - A43-32 (IGSW) Always Below 1 Ω
1G-1 - A43-2 (+B) Always Below 1 Ω
1G-2 - A43-3 (+B2) Always Below 1 Ω
1G-6 - A43-46 (MREL) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
a.

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C1-49 (E1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (BATTERY - IGNITION SWITCH ASSEMBLY)
a.

Disconnect the ignition switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F50-4 (AM2) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

7.INSPECT IGNITION SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT IGNITION SWITCH ASSEMBLY
a.

Inspect the ignition switch assembly.

Click hereEngine / Hybrid System>2GR-FE STARTING>IGNITION SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (SEMICONDUCTOR PWR INTEGRATION ECU - IGNITION SWITCH ASSEMBLY)

NG

REPLACE IGNITION SWITCH ASSEMBLY

8.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - SEMICONDUCTOR PWR INTEGRATION ECU)
a.

Disconnect the semiconductor pwr integration ECU connector.


b.

Disconnect the certification ECU (smart key ECU assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F10-3 (IG1D) - 1E-1 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR