Home › Drivetrain › U660F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM › 2013.12–2016.11
RM3160E _52 Drivetrain _019726 U660F AUTOMATIC TRANSMISSION / TRANSAXLE _0109808 AUTOMATIC TRANSAXLE SYSTEM C

U660F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  U0100  Lost Communication with ECM / PCM "A"  


DESCRIPTION

The engine control unit communicates with the TCM using the Controller Area Network (CAN).

If there is a problem in this communication, the TCM stores this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
U0100 Lost Communication with ECM / PCM "A" Following conditions are met for 1.25 seconds (1 trip detection logic):
·

Ignition switch ON

·

Battery voltage is 10.5 V or more

·

No communication between the engine control ECU (ECM) and TCM


·

Harness and connector

·

ECM

·

TCM


Comes on DTC stored

WIRING DIAGRAM

C301527
5.5,0.729 5.656,0.927 0.156,0.198 10 false S 5.5,1.135 6.115,1.333 0.615,0.198 10 false SFTU 5.49,1.552 6.104,1.75 0.615,0.198 10 false SFTD 5.51,2.927 6.125,3.125 0.615,0.198 10 false CAN+ 5.51,3.417 6.125,3.615 0.615,0.198 10 false CAN- 5.156,0.729 5.615,0.927 0.458,0.198 10 false A43 5.156,1.135 5.615,1.333 0.458,0.198 10 false A43 5.156,1.542 5.615,1.74 0.458,0.198 10 false A43 5.177,2.917 5.49,3.115 0.313,0.198 10 false C1 5.188,3.417 5.5,3.615 0.313,0.198 10 false C1 5.833,3.99 6.292,4.188 0.458,0.198 10 false ECM 4.125,0.615 4.281,0.813 0.156,0.198 10 false 7 4.125,1.031 4.281,1.229 0.156,0.198 10 false 2 4.115,1.438 4.271,1.635 0.156,0.198 10 false 1 2.688,0.615 2.844,0.813 0.156,0.198 10 false 3 2.688,1.438 2.844,1.635 0.156,0.198 10 false 5 3.927,0.635 4.083,0.833 0.156,0.198 10 false S 3.688,1.042 4.302,1.24 0.615,0.198 10 false SFTU 3.688,1.438 4.302,1.635 0.615,0.198 10 false SFTD 2.865,0.625 3.177,0.823 0.313,0.198 10 false IG 2.865,1.438 3.115,1.719 0.25,0.281 10 false E 0.385,0.729 1.781,1.083 1.396,0.354 10 false from IG1 NO.3 fuse 0.865,4.469 4.531,4.667 3.667,0.198 10 false : CAN Communication Line 5.198,2.74 5.51,2.938 0.313,0.198 10 false 31 5.24,3.229 5.396,3.427 0.156,0.198 10 false 1 3.875,2.771 4.031,2.969 0.156,0.198 10 false 6 3.885,3.25 4.042,3.448 0.156,0.198 10 false 7 3.427,2.917 4.042,3.115 0.615,0.198 10 false CAN+ 3.448,3.406 4.063,3.604 0.615,0.198 10 false CAN- 3.135,3.958 3.448,4.156 0.313,0.198 10 false C3 3.396,3.958 3.854,4.156 0.458,0.198 10 false TCM 2.49,1.865 2.948,2.063 0.458,0.198 10 false F46 2.479,2.021 4.323,2.583 1.844,0.563 10 false Lower Shift Lever Assembly (Transmission Control Switch) 5.198,0.542 5.698,0.823 0.5,0.281 10 false 37 5.198,0.958 5.51,1.156 0.313,0.198 10 false 34 5.208,1.365 5.521,1.563 0.313,0.198 10 false 50

CAUTION / NOTICE / HINT

HINT:
·

Refer to inspection procedure for CAN communication system.

·

If the CAN communication malfunctions, the TCM cannot receive the current data from the ECM. In this case, the freeze frame data output from the TCM has not been updated, so the data will not be useful for the inspection. However, reading the Data List as the first step in troubleshooting is effective to find malfunctions.

·

The malfunction area can be checked using the Bus Check function on the GTS.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



PROCEDURE

1.CHECK ECU TERMINAL VOLTAGE (+B AND E1 TERMINALS)
a.
C189544
0.208,1.104 0.615,1.375 0.406,0.271 1.031,2.167 0.625,2.802 false 1.135,2.354 1.052,2.781 false 0.135,0.177 0.354,0.417 0.219,0.24 10 false *a 0.344,1.156 0.656,1.313 0.313,0.156 10 false C3 0.51,2.823 0.813,3.031 0.302,0.208 10 false E1 0.969,2.823 1.458,3 0.49,0.177 10 false +B
*a Front view of wire harness connector
(to TCM)


Disconnect the TCM connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C3-18 (+B) - C3-8 (E1) Ignition switch ON 9 to 14 V



d.

Turn the ignition switch off.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C3-8 (E1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (TCM - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (TCM - ECM)
a.

Disconnect the TCM connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C3-6 (CAN+) - C1-31 (CAN+) Always Below 1 Ω
C3-7 (CAN-) - C1-1 (CAN-) Always Below 1 Ω
C3-6 (CAN+) or C1-31 (CAN+) - Body ground and other terminals Always 10 kΩ or higher
C3-7 (CAN-) or C1-1 (CAN-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK IF DTC OUTPUT RECURS

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK IF DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.


Powertrain > ECT > Clear DTCs
50002 235
c.

Replace the TCM.

HINT:

Replace the TCM with a TCM from a normally functioning vehicle of the same model.



d.

Start the engine.


e.

Read the DTCs.

Powertrain > ECT > Trouble Codes
50001 235
Result:
Result Proceed to
DTC U0100 is output A
DTCs are not output B




A

B