Home › Engine / Hybrid System › CRUISE CONTROL › CRUISE CONTROL SYSTEM › 2013.12–2016.11
RM3160E _51 Engine / Hybrid System _019684 CRUISE CONTROL _0109815 CRUISE CONTROL SYSTEM C

CRUISE CONTROL  CRUISE CONTROL SYSTEM  P0571  Brake Switch "A" Circuit  


DESCRIPTION

When the brake pedal is depressed, the stop light switch assembly sends a signal to the ECM. When the ECM receives this signal, it cancels control of vehicle speed by the cruise control system. The fail-safe function operates to enable normal driving even if there is a malfunction in the stop light signal circuit. The cancellation condition occurs when voltage is applied to terminal STP. When the brake is applied, voltage is applied to terminal STP of the ECM through the STOP fuse and the stop light switch assembly, and the ECM cancels control of vehicle speed by the cruise control system.

DTC No. Detection Item DTC Detection Condition Trouble Area
P0571 Brake Switch "A" Circuit When voltage of STP terminal and that of ST1- terminal of ECM are less than 1 V for 0.5 sec. or more.
·

Stop light switch assembly

·

Stop light switch circuit

·

ECM



WIRING DIAGRAM

E267669
5.708,0.76 6.167,0.958 0.458,0.198 10 false STP 5.698,1.563 6.156,1.76 0.458,0.198 10 false ST1- 5.313,0.635 5.771,0.833 0.458,0.198 10 false 51*2 5.323,1.438 5.781,1.635 0.458,0.198 10 false 36*2 2.948,1.917 3.406,2.115 0.458,0.198 10 false A54 0.333,0.76 1.042,1.094 0.708,0.333 10 false from STOP Fuse 0.125,1.552 1.125,1.813 1,0.26 10 false from IG2 Fuse 3.844,0.646 4.042,0.823 0.198,0.177 10 false 1 3.854,1.427 4.021,1.625 0.167,0.198 10 false 3 2.927,2.115 4.927,2.354 2,0.24 10 false Stop Light Switch Assembly 5.635,2.115 6.094,2.313 0.458,0.198 10 false A43 2.917,0.646 3.083,0.833 0.167,0.188 10 false 2 2.917,1.427 3.083,1.615 0.167,0.188 10 false 4 6.073,2.125 6.885,2.323 0.813,0.198 10 false ECM 5.313,0.469 5.771,0.667 0.458,0.198 10 false 11*1 5.323,1.271 5.781,1.469 0.458,0.198 10 false 24*1 1.25,2.083 2.25,2.25 1,0.167 10 false *1: for 1AR-FE 1.25,2.417 2.25,2.583 1,0.167 10 false *2: for 2GR-FE

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF STOP LIGHT SWITCH ASSEMBLY)
a.

Disconnect the A54 stop light switch assembly connector.


b.
E144327
0.396,1.958 0.833,2.302 0.438,0.344 0.5,2.052 1.104,2.469 0.604,0.417 10 false A54 0.24,0.177 0.656,0.573 0.417,0.396 10 false *a
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A54-2 - Body ground Always 11 to 14 V
A54-4 - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BATTERY OR IG2 RELAY)

2.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Inspect the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (ECM - STOP LIGHT SWITCH ASSEMBLY)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (ECM - STOP LIGHT SWITCH ASSEMBLY)
a.

Disconnect the A43 ECM connector.


b.

Disconnect the A54 stop light switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 1AR-FE
Tester Connection Condition Specified Condition
A43-11 (STP) - A54-1 Always Below 1 Ω
A43-24 (ST1-) - A54-3 Always Below 1 Ω
A43-11 (STP) or A54-1 - Body ground Always 10 kΩ or higher
A43-24 (ST1-) or A54-3 - Body ground Always 10 kΩ or higher

for 2GR-FE
Tester Connection Condition Specified Condition
A43-36 (ST1-) - A54-3 Always Below 1 Ω
A43-51 (STP) - A54-1 Always Below 1 Ω
A43-36 (ST1-) or A54-3 - Body ground Always 10 kΩ or higher
A43-51 (STP) or A54-1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - STOP LIGHT SWITCH ASSEMBLY)