Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Manual Air Conditioning System)
RM3160E _58 Vehicle Interior _019714 HEATING / AIR CONDITIONING _0109952 AIR CONDITIONING SYSTEM(for Manual Air Conditioning System) C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Manual Air Conditioning System)  B1413  Evaporator Temperature Sensor Circuit  


DESCRIPTION

The No. 1 cooler thermistor is installed on the evaporator in the air conditioner unit to detect the temperature of the cooled air that has passed through the evaporator, which is used to control the air conditioning system. It sends signals to the air conditioning amplifier assembly. The resistance of the No. 1 cooler thermistor changes in accordance with the temperature of the cooled air that has passed through the evaporator. As the temperature decreases, the resistance increases. As the temperature increases, the resistance decreases.

The air conditioning amplifier assembly applies voltage (5 V) to the No. 1 cooler thermistor and reads voltage changes as the resistance of the No. 1 cooler thermistor changes. This sensor is used for frost prevention.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory
B1413 Evaporator Temperature Sensor Circuit Open or short in evaporator temperature sensor circuit
·

No. 1 cooler thermistor

·

Air conditioning harness assembly

·

Air conditioning amplifier assembly


Memorized
(4 sec. or more)*1

*1: The air conditioning amplifier assembly stores this DTC if the malfunction has occurred for the period of time indicated in the brackets.


WIRING DIAGRAM

E229251E43
2.031,1.396 2.375,1.656 0.344,0.26 10 false 2 2.031,0.438 2.125,0.615 0.094,0.177 10 false 1 4.771,0.448 4.99,0.719 0.219,0.271 10 false 6 4.792,1.396 5.156,1.677 0.365,0.281 10 false 5 4.969,0.552 5.677,0.844 0.708,0.292 10 false TEA 2.688,1.906 4.24,2.26 1.552,0.354 10 false Air Conditioning Harness Assembly 4.969,1.5 5.583,1.813 0.615,0.313 10 false SGA 0.906,1.979 2.448,2.302 1.542,0.323 10 false No. 1 Cooler Thermistor 4.708,1.896 5.01,2.146 0.302,0.25 10 false z3 4.708,2.063 6.281,2.396 1.573,0.333 10 false Air Conditioning Amplifier Assembly

PROCEDURE

1.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Air Conditioner / Data List.


e.

Check the value(s) by referring to the table below.

Body Electrical > Air Conditioner > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Evaporator Fin Thermistor No. 1 cooler thermistor Min.: -30.00°C (-22.00°F)
Max.: 59.60°C (139.28°F)
Actual evaporator temperature displayed -
Body Electrical > Air Conditioner > Data List
Tester Display
Evaporator Fin Thermistor
50003 121 3
OK:

The display is as specified in the normal condition column.



Result:
Result Proceed to
NG A
OK (When troubleshooting according to Problem Symptoms Table) B
OK (When troubleshooting according to the DTC) C



A

2.INSPECT NO. 1 COOLER THERMISTOR

B

C

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

2.INSPECT NO. 1 COOLER THERMISTOR
a.

Remove the No. 1 cooler thermistor.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>FRONT EVAPORATOR TEMPERATURE SENSOR>REMOVAL

E287489C01
0.208,1.656 0.417,1.375 false 5.708,1.333 5.917,1.052 false 1.125,0.76 1.438,0.958 0.313,0.198 10 false *a 0.417,1.229 0.729,1.427 0.313,0.198 10 false *b 4.646,0.021 4.958,0.219 0.313,0.198 10 false *c 5.938,2.521 6.25,2.719 0.313,0.198 10 false *d 5.917,0.885 6.229,1.083 0.313,0.198 10 false *e
*a Component without harness connected
(No. 1 Cooler Thermistor)
*b Sensing Portion
*c Resistance (kΩ) *d Temperature (°C (°F))
*e Allowable Range - -



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 -10°C (14°F) 7.30 to 9.10 kΩ
-5°C (23°F) 5.65 to 6.95 kΩ
0°C (32°F) 4.40 to 5.35 kΩ
5°C (41°F) 3.40 to 4.15 kΩ
10°C (50°F) 2.70 to 3.25 kΩ
15°C (59°F) 2.14 to 2.58 kΩ
20°C (68°F) 1.71 to 2.05 kΩ
25°C (77°F) 1.38 to 1.64 kΩ
30°C (86°F) 1.11 to 1.32 kΩ


NOTICE:
·

Hold the sensor only by its connector. Touching the sensing portion may change the resistance value.

·

When measuring, the sensor temperature must be the same as the ambient temperature.



HINT:

As the temperature increases, the resistance decreases (see the graph).



Result:
Proceed to
OK
NG



OK

3.INSPECT AIR CONDITIONING HARNESS ASSEMBLY

NG

3.INSPECT AIR CONDITIONING HARNESS ASSEMBLY
a.
E161765C15
0.573,2.281 0.938,2.521 0.365,0.24 1.594,2.74 2.063,3.083 false 1.406,2.729 1.156,3.083 false 0.188,0.188 0.344,0.344 0.156,0.156 10 false *a 0.688,2.313 0.969,2.573 0.281,0.26 10 false z3 1.021,3.083 1.385,3.229 0.365,0.146 10 false SGA 1.948,3.083 2.271,3.229 0.323,0.146 10 false TEA
*a Front view of wire harness connector
(to Air Conditioning Amplifier Assembly)


Remove the air conditioning harness assembly.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>FRONT AIR CONDITIONING UNIT>DISASSEMBLY


b.
E124472C06
0.188,0.5 0.49,0.823 0.302,0.323 10 *a
*a Front view of wire harness connector
(to No. 1 Cooler Thermistor)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z3-6 (TEA) - 1 Always Below 1 Ω
z3-5 (SGA) - 2 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG