The blower damper servo sub-assembly (air inlet) sends pulse signals to inform the air conditioning amplifier assembly of the damper position. The air conditioning amplifier assembly activates the motor (normal or reverse) based on these signals to move the air inlet mode selection blower damper servo sub-assembly (air inlet) to the appropriate position, which controls the air inlet mode (fresh, recirculation/fresh, and recirculation).
The air conditioning amplifier assembly communicates with the servo through a communication/driver IC and wiring assembly called the air conditioning harness assembly.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Memory |
|---|---|---|---|---|
| B1442 | Air Inlet Damper Control Servo Motor Circuit | Air inlet damper position sensor value does not change even if air conditioning amplifier assembly operates blower damper servo sub-assembly (air inlet) | ·
Blower damper servo sub-assembly (air inlet) ·
Air conditioning harness assembly ·
Air conditioning amplifier assembly |
Memorized
(30 sec. or more)*1 |
*1: The air conditioning amplifier assembly stores this DTC if the malfunction has occurred for the period of time indicated in the brackets.
Confirm that no mechanical problems are present because this DTC can be output when either a damper link or damper is mechanically locked.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Operate the recirculation/fresh switch.
Enter the following menus: Body Electrical / Air Conditioner / Data List.
Check the value(s) by referring to the table below.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Air Inlet Damper Targ Pulse | Blower damper servo sub-assembly (air inlet) target pulse | Min.: 128
Max.: 383 |
·
Recirculation: 7 (pulse) ·
Fresh: 28 (pulse) |
- |
| Air Inlet Damper Actual Pulse | Blower damper servo sub-assembly (air inlet) actual pulse | Min.: 128
Max.: 383 |
·
Recirculation: 7 (pulse) ·
Fresh: 28 (pulse) |
- |
| Tester Display |
|---|
| Air Inlet Damper Targ Pulse |
| Air Inlet Damper Actual Pulse |
When the recirculation/fresh switch is operated, the actual pulse changes following the target pulse.
| Result | Proceed to |
|---|---|
| Target pulse changes but actual pulse does not change | A |
| Target pulse and actual pulse do not change | B |
| Actual pulse changes following the target pulse (When troubleshooting according to the DTC) | C |
| Actual pulse changes following the target pulse (When troubleshooting according to Problem Symptoms Table) | D |
A
B
C
D
Replace the blower damper servo sub-assembly (air inlet).
Click hereVehicle Interior>HEATING / AIR CONDITIONING>BLOWER UNIT>DISASSEMBLY
Since the servo motor cannot be inspected while it is removed from the vehicle, replace the servo motor with a new or known good one and check that the condition returns to normal.
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC B1442 is output | A |
| DTC B1442 is not output | B |
A
B
Replace the air conditioning harness assembly.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>FRONT AIR CONDITIONING UNIT>DISASSEMBLY
Since the air conditioning harness assembly cannot be inspected while it is removed from the vehicle, replace the air conditioning harness assembly with a new or known good one and check that the condition returns to normal.
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC B1442 is output | A |
| DTC B1442 is not output | B |
A
B
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC B1442 is output | A |
| DTC B1442 is not output | B |
A
B
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING