The air conditioning harness assembly connects the air conditioning amplifier assembly and the servo motors. The air conditioning amplifier assembly supplies power and sends operation instructions to each servo motor through the air conditioning harness assembly. Each servo motor sends damper position information to the air conditioning amplifier assembly.
The No. 2 air conditioning harness assembly connects the air conditioning amplifier assembly and the servo motors. The air conditioning amplifier assembly supplies power and sends operation instructions to each servo motor through the No. 2 air conditioning harness assembly. Each servo motor sends damper position information to the air conditioning amplifier assembly.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Memory |
|---|---|---|---|---|
| B1497 | Communication Malfunction (Bus Ic) | Error or open in communication line | ·
Air conditioning harness assembly ·
No. 1 air conditioning radiator damper servo sub-assembly (air mix) ·
No. 1 air conditioning radiator damper servo sub-assembly (air outlet) ·
Blower damper servo sub-assembly (air inlet) ·
No. 2 air conditioning harness assembly ·
Rear air mix damper servo sub-assembly ·
Rear mode damper servo sub-assembly ·
Air conditioning amplifier assembly |
Memorized
(10 sec. or more)*1 |
*1: The air conditioning amplifier assembly stores this DTC if the malfunction has occurred for the period of time indicated in the brackets.
for Front Side
for Rear Side
Inspect the fuses for circuits related to this system before performing the following procedure.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Air Conditioner / Active test.
Check the operation by referring to the table below.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Air Mix Servo Targ Pulse(D) | No. 1 air conditioning radiator damper servo sub-assembly (air mix) pulse | Min.: 128
Max.: 383 |
Operates between 7 to 105 pulses |
| Air Outlet Servo Pulse (D) | No. 1 air conditioning radiator damper servo sub-assembly (air outlet) pulse | Min.: 128
Max.: 383 |
Operates between 8 to 97 pulses |
| Air Inlet Damper Targ Pulse | Blower damper servo sub-assembly (air inlet) pulse | Min.: 128
Max.: 383 |
Operates between 7 to 28 pulses |
| A/M Servo Pulse(F&R D) | Rear air mix damper servo sub-assembly pulse | Min.: 128
Max.: 383 |
Operates between 9 to 54 pulses |
| A/O Servo Pulse(F&R D) | Rear mode damper servo sub-assembly pulse | Min.: 128
Max.: 383 |
Operates between 7 to 83 pulses |
| Tester Display |
|---|
| Air Mix Servo Targ Pulse(D) |
| Tester Display |
|---|
| Air Outlet Servo Pulse (D) |
| Tester Display |
|---|
| Air Inlet Damper Targ Pulse |
| Tester Display |
|---|
| A/M Servo Pulse(F&R D) |
| Tester Display |
|---|
| A/O Servo Pulse(F&R D) |
Arm of the damper servo motor selected in the Active Test operates smoothly.
According to the test result, proceed to the next step.
| Result | Proceed to |
|---|---|
| One of the front damper servo motors is malfunctioning | A |
| All of the front damper servo motors are malfunctioning | B |
| One of the rear damper servo motors is malfunctioning | C |
| All of the rear damper servo motors are malfunctioning | D |
| All of the damper servo motors are normal | E |
A
B
C
D
E
According to the test result, proceed to the next step.
| Result | Proceed to |
|---|---|
| Only the No. 1 air conditioning radiator damper servo sub-assembly (air mix) is malfunctioning | A |
| Only the No. 1 air conditioning radiator damper servo sub-assembly (air outlet) is malfunctioning | B |
| Only the blower damper servo sub-assembly (air inlet) is malfunctioning | C |
A
B
C
Replace the No. 1 air conditioning radiator damper servo sub-assembly (air mix).
Click hereVehicle Interior>HEATING / AIR CONDITIONING>FRONT AIR CONDITIONING UNIT>DISASSEMBLY
Since the servo motor cannot be inspected while it is removed from the vehicle, replace the servo motor with a new or known good one and check that the condition returns to normal.
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC B1497 is not output | A |
| DTC B1497 is output | B |
A
B
Replace the No. 1 air conditioning radiator damper servo sub-assembly (air outlet).
Click hereVehicle Interior>HEATING / AIR CONDITIONING>FRONT AIR CONDITIONING UNIT>DISASSEMBLY
Since the servo motor cannot be inspected while it is removed from the vehicle, replace the servo motor with a new or known good one and check that the condition returns to normal.
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC B1497 is not output | A |
| DTC B1497 is output | B |
A
B
Replace the blower damper servo sub-assembly (air inlet).
Click hereVehicle Interior>HEATING / AIR CONDITIONING>BLOWER UNIT>DISASSEMBLY
Since the servo motor cannot be inspected while it is removed from the vehicle, replace the servo motor with a new or known good one and check that the condition returns to normal.
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC B1497 is not output | A |
| DTC B1497 is output | B |
A
B
Replace the air conditioning harness assembly.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>FRONT AIR CONDITIONING UNIT>DISASSEMBLY
Since the air conditioning harness assembly cannot be inspected while it is removed from the vehicle, replace the air conditioning harness assembly with a new or known good one and check that the condition returns to normal.
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC B1497 is not output | A |
| DTC B1497 is output | B |
A
B
Disconnect the F80 air conditioning amplifier assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F80-21 (B) - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
According to the test result, proceed to the next step.
| Result | Proceed to |
|---|---|
| Only the rear air mix damper servo sub-assembly is malfunctioning | A |
| Only the rear mode damper servo sub-assembly is malfunctioning | B |
A
B
Replace the rear air mix damper servo sub-assembly.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>REAR AIR CONDITIONING UNIT>DISASSEMBLY
Since the servo motor cannot be inspected while it is removed from the vehicle, replace the servo motor with a new or known good one and check that the condition returns to normal.
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC B1497 is not output | A |
| DTC B1497 is output | B |
A
B
Replace the rear mode damper servo sub-assembly.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>REAR AIR CONDITIONING UNIT>DISASSEMBLY
Since the servo motor cannot be inspected while it is removed from the vehicle, replace the servo motor with a new or known good one and check that the condition returns to normal.
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC B1497 is not output | A |
| DTC B1497 is output | B |
A
B
Disconnect the L20 No. 2 air conditioning harness assembly connector.
Disconnect the F81 air conditioning amplifier assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F81-27 (R BBU) - L20-4 (R BBU) | Always | Below 1 Ω |
| F81-1 (R BUS) - L20-3 (R BUS) | Always | Below 1 Ω |
| F81-25 (R BUG) - L20-2 (R BUG) | Always | Below 1 Ω |
| F81-27 (R BBU) - Body ground | Always | 10 kΩ or higher |
| F81-1 (R BUS) - Body ground | Always | 10 kΩ or higher |
| F81-25 (R BUG) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the No. 2 air conditioning harness assembly.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>REAR AIR CONDITIONING UNIT>DISASSEMBLY
Since the No. 2 air conditioning harness assembly cannot be inspected while it is removed from the vehicle, replace the No. 2 air conditioning harness assembly with a new or known good one and check that the condition returns to normal.
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC B1497 is not output | A |
| DTC B1497 is output | B |
A
B
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F81-28 (+B2) - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG