Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Manual Air Conditioning System) › 2013.12–2016.11
RM3160E _58 Vehicle Interior _019714 HEATING / AIR CONDITIONING _0109952 AIR CONDITIONING SYSTEM(for Manual Air Conditioning System) J

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Manual Air Conditioning System)  Air Conditioning Compressor Magnetic Clutch Circuit  


DESCRIPTION

When the air conditioning amplifier assembly is turned on, a magnetic clutch on signal is sent from the MGC terminal of the air conditioning amplifier assembly. Then, the semiconductor pwr integration ECU turns on to operate the magnetic clutch assembly.

WIRING DIAGRAM

E287517
1.604,1.01 2.063,1.208 0.458,0.198 10 false ECM 2.281,3.573 2.74,3.771 0.458,0.198 10 false 1G 2.281,3.104 2.74,3.302 0.458,0.198 10 false 1D 2.302,2.594 2.76,2.792 0.458,0.198 10 false 1D 3.656,1.813 4.115,2.01 0.458,0.198 10 false 1D 3.656,2.521 4.115,2.719 0.458,0.198 10 false 1D 2.302,2.073 2.76,2.271 0.458,0.198 10 false 1A 2.281,1.573 2.74,1.771 0.458,0.198 10 false 1B 2.333,1.375 2.792,1.573 0.458,0.198 10 false 1 2.344,1.865 2.802,2.063 0.458,0.198 10 false 1 2.313,2.396 2.771,2.594 0.458,0.198 10 false 11 2.313,2.906 2.771,3.104 0.458,0.198 10 false 14 2.333,3.385 2.792,3.583 0.458,0.198 10 false 5 3.688,1.625 4.146,1.823 0.458,0.198 10 false 4 3.667,2.333 4.125,2.531 0.458,0.198 10 false 12 1.646,2.24 2.417,2.469 0.771,0.229 10 false ALT 1.469,2.75 2.24,2.979 0.771,0.229 10 false IG1 NO. 3 2.656,1.552 3.427,1.781 0.771,0.229 10 false BATT 2.656,2.083 3.427,2.313 0.771,0.229 10 false ALT 2.656,2.573 3.427,2.802 0.771,0.229 10 false IGN 2.656,3.115 3.427,3.344 0.771,0.229 10 false GND1 2.656,3.563 3.427,3.792 0.771,0.229 10 false GND2 3.094,1.823 3.865,2.052 0.771,0.229 10 false ACOS 3.094,2.521 3.865,2.75 0.771,0.229 10 false ACOP 4.385,2.448 4.844,2.646 0.458,0.198 10 false 3 4.563,2.438 5.021,2.635 0.458,0.198 10 false MG+ 4.146,3.01 4.604,3.208 0.458,0.198 10 false C12 6.083,1.719 6.542,1.917 0.458,0.198 10 false 20 6.365,1.823 6.823,2.021 0.458,0.198 10 false MGC 5.271,3.75 5.729,3.948 0.458,0.198 10 false F80 0.219,1.563 1.583,1.792 1.365,0.229 10 false from Battery 0.229,2.073 1.594,2.302 1.365,0.229 10 false from Battery 0.094,2.625 1.063,3.073 0.969,0.448 10 false from IG1 NO. 3 Relay 2.458,3.885 3.708,4.333 1.25,0.448 10 false Semiconductor Pwr Integration ECU 4.146,3.156 6.208,3.396 2.063,0.24 10 false Cooler Compressor Assembly 4.156,3.427 6.219,3.667 2.063,0.24 10 false - Magnetic Clutch Assembly 5.604,3.74 7.156,4.104 1.552,0.365 10 false Air Conditioning Amplifier Assembly 4.771,4.417 6.833,4.656 2.063,0.24 10 false : CAN Communication Line 4.948,2.448 5.156,2.625 0.208,0.177 10 false 1

CAUTION / NOTICE / HINT

NOTICE:
·

ECM malfunctions can affect the storage of this DTC. Therefore, check all SFI system DTCs and confirm that the system is normal before performing the following inspection.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Using the GTS, check if the CAN communication system is functioning normally.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING


Result:
Result Proceed to
CAN communication system DTCs are not output A
CAN communication system DTCs are output B



A

2.CHECK SEMICONDUCTOR PWR INTEGRATION ECU

B

2.CHECK SEMICONDUCTOR PWR INTEGRATION ECU
a.

Using a voltmeter, check the signal reading of the semiconductor pwr integration ECU.

Click herePower Source / Network>POWER DISTRIBUTION>INTEGRATION RELAY>ON-VEHICLE INSPECTION

OK:

A normal signal reading is output.



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (SEMICONDUCTOR PWR INTEGRATION ECU - POWER SOURCE AND BODY GROUND)

NG

CHECK SEMICONDUCTOR PWR INTEGRATION ECU (RESULT OF SIGNAL READING)

3.CHECK HARNESS AND CONNECTOR (SEMICONDUCTOR PWR INTEGRATION ECU - POWER SOURCE AND BODY GROUND)
a.

Remove the semiconductor pwr integration ECU from the No. 1 engine room relay block and No. 1 junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>INTEGRATION RELAY>REMOVAL


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
1A-1 (ALT) - Body ground Always 11 to 14 V
1B-1 (BATT) - Body ground Always 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1D-14 (GND1) - Body ground Always Below 1 Ω
1G-5 (GND2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (SEMICONDUCTOR PWR INTEGRATION ECU - COOLER COMPRESSOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (SEMICONDUCTOR PWR INTEGRATION ECU - COOLER COMPRESSOR ASSEMBLY)
a.

Disconnect the C12 cooler compressor assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1D-12 (ACOP) - C12-3 (MG+) Always Below 1 Ω
1D-12 (ACOP) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (SEMICONDUCTOR PWR INTEGRATION ECU - AIR CONDITIONING AMPLIFIER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (SEMICONDUCTOR PWR INTEGRATION ECU - AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.

Disconnect the F80 air conditioning amplifier assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1D-4 (ACOS) - F80-20 (MGC) Always Below 1 Ω
1D-4 (ACOS) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK MAGNETIC CLUTCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK MAGNETIC CLUTCH ASSEMBLY
a.

Connect the magnetic clutch assembly connector.


b.
E285435C01
1.271,1.75 1.646,1.448 false 0.167,0.146 0.479,0.302 0.313,0.156 10 false *a 1.115,1.76 1.594,2.052 0.479,0.292 10 false MG+
*a Component without harness connected
(Cooler Compressor Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (MG+) - Body ground 20°C (68°F) 3.8 to 4.2 Ω



c.

When connector terminal 3 (MG+) is connected to a positive (+) battery terminal, check that the following occurs: 1) the magnetic clutch operating sound can be heard, and 2) the magnetic clutch hub and rotor lock.

OK:

1) The magnetic clutch assembly operating sound can be heard, and 2) the magnetic clutch hub and rotor lock.



Result:
Proceed to
OK
NG



OK

NG