Home › Vehicle Interior › HEATING / AIR CONDITIONING › FRONT AIR CONDITIONING UNIT
RM3160E _58 Vehicle Interior _019714 HEATING / AIR CONDITIONING _0109955 FRONT AIR CONDITIONING UNIT A

HEATING / AIR CONDITIONING  FRONT AIR CONDITIONING UNIT  REASSEMBLY  


PROCEDURE

Hide 87050C 1.INSTALL NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY

a.
E227210

Check that the slots, links and gears of the No. 1 air conditioning radiator damper servo sub-assembly are positioned with the correct orientation as shown in the illustration.


b.

Face the contact surfaces of the No. 1 air conditioning radiator damper servo sub-assembly and air conditioning radiator assembly upward.


c.

Rotate the link of the air conditioning radiator assembly all the way to the left as shown in the illustration.

E287817


d.

Rotate the link of the air conditioning radiator assembly to the bottom as shown in the illustration and confirm that the mode switching duct hole is fully closed.

E287818
1.333,1.917 1.5,1.917 1.5,1.917 1.667,2.448 false 1.146,1.802 1.458,2 0.313,0.198 10 false *a
*a Mode Switching Duct Hole - -



e.

Rotate the lever of the air conditioning radiator assembly to the top as shown in the illustration.

E287819


f.

Rotate the link of the air conditioning radiator assembly to the in-line position as shown in the illustration.

E287820
5.552,0.25 5.917,0.229 false 5.938,0.125 6.25,0.323 0.313,0.198 10 true *a
*a In-line Position - -



g.
E287821
2.302,1.021 2.333,0.979 false
V100155

Vinyl Tape


Wrap the upper and lower links with vinyl tape to hold them in the in-line position.


h.

Install the link of the No. 1 air conditioning radiator damper servo sub-assembly to the link guide pin (A) of the air conditioning radiator assembly as shown in the illustration.

E287822
0.5,0.26 0.667,0.26 0.667,0.26 0.771,0.542 true 0.583,2.354 0.75,2.354 0.75,2.354 1.01,3 true 1.198,2.865 1.417,2.25 1.417,2.25 1.583,2.25 false 6.333,2.333 6.5,2.333 6.5,2.333 6.625,2.063 false 6.302,1.896 6.5,1.521 6.5,1.521 6.667,1.521 true 1.604,2.146 1.917,2.302 0.313,0.156 10 false *1 0.323,0.146 0.635,0.302 0.313,0.156 10 false *a 6.146,2.229 6.458,2.385 0.313,0.156 10 false *b 0.417,2.25 0.729,2.406 0.313,0.156 10 false *c 6.688,1.417 7,1.573 0.313,0.156 10 false *d
*1 No. 1 Air Conditioning Radiator Damper Servo Sub-assembly - -
*a Guide *b No. 1 Air Conditioning Radiator Damper Servo Sub-assembly Slot
*c Link Guide Pin (A) *d Link Guide Pin (B)



i.

Engage the guide of the air conditioning radiator assembly to the No. 1 air conditioning radiator damper servo sub-assembly as shown in the illustration.


j.

Temporarily install the screw (up to 4 or 5 threads).

NOTICE:
·

Make sure that the link guide pin (B) is inserted in the No. 1 air conditioning radiator damper servo sub-assembly slot.

·

Avoid tilting the air conditioning radiator assembly during installation. This helps to prevent the link guide pins from coming out of position.




k.
E287823

Lift the No. 1 air conditioning radiator damper servo sub-assembly slightly to create clearance.


l.

Move the air conditioning radiator assembly gear so that the alignment holes of the No. 1 air conditioning radiator damper servo sub-assembly and air conditioning radiator assembly are aligned.

E287824
0.938,3.063 1.885,3.063 true 1.802,1.635 2.802,1.635 true 2.125,3.083 2.906,3.083 true 1.625,1.531 1.938,1.688 0.313,0.156 10 false *a 0.76,2.969 1.073,3.125 0.313,0.156 10 false *b 2.927,2.99 3.24,3.146 0.313,0.156 10 false *c
*a No. 1 Air Conditioning Radiator Damper Servo Sub-assembly Alignment Hole *b Air Conditioning Radiator Assembly Alignment Hole
*c Air Conditioning Radiator Assembly Gear Alignment Hole - -



m.
E287825

Insert a screwdriver into the alignment holes as shown in the illustration.


n.

Make sure that all the links and gears are in the positions shown in the illustration.

E287826
0.302,2.406 0.927,1.854 true 5.99,2.063 6.396,1.833 6.396,1.833 5.792,2.031 true 5.615,0.688 6.01,0.802 false 4.844,1.719 4.844,1.26 true 6.229,1.292 6.646,1.125 true 5.188,2.74 5.188,2.406 false 1.688,4.104 2.146,3.844 true 5.271,3.771 5.594,3.833 false 0.125,2.333 0.438,2.49 0.313,0.156 10 false *a 4.802,1.729 5.115,1.885 0.313,0.156 10 false *b 5.438,0.573 5.75,0.729 0.313,0.156 10 false *c 5.125,2.75 5.438,2.906 0.313,0.156 10 false *d 6.667,1.01 6.979,1.167 0.313,0.156 10 false *e 2.167,3.74 2.49,3.958 0.323,0.219 10 false *f 5.615,3.708 5.854,3.917 0.24,0.208 10 true *g 6.417,1.708 6.729,1.865 0.313,0.156 10 false *e
*a Screwdriver is inserted into alignment holes. *b Link guide pin is inserted.
*c Link is positioned to left side. *d Link is positioned at bottom.
*e Each link guide pin is inserted in its No. 1 air conditioning radiator damper servo sub-assembly slot. *f Lever is positioned at top.
*g Links are in-line. - -



o.
E287827

Push the No. 1 air conditioning radiator damper servo sub-assembly into position.

NOTICE:
·

Make sure that the No. 1 air conditioning radiator damper servo sub-assembly is fully pushed into position.

·

After pushing the No. 1 air conditioning radiator damper servo sub-assembly into position, keep it in place by holding it until the screws are installed.



HINT:

Push the No. 1 air conditioning radiator damper servo sub-assembly until a click sound is heard.



p.

Remove the screwdriver.


q.
E287816

Fully tighten the top screw, and then install the No. 1 air conditioning radiator damper servo sub-assembly with the 2 screws.


r.

Remove the vinyl tape.


Hide 87107A 2.INSTALL HEATER RADIATOR UNIT SUB-ASSEMBLY

a.
E287812

Install the heater radiator unit sub-assembly.


b.
E287811

Install the clamp with the screw.


c.
E287810

Engage the 3 claws to install the heater clamp.


Hide 87050D 3.INSTALL NO. 2 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY (for Automatic Air Conditioning System)

a.
E287814
2.156,0.99 2.833,0.375 2.833,0.375 2.271,0.979 true 2.854,0.24 3.167,0.438 0.313,0.198 10 false *a
*a Reference Point


Using the reference points, install the air mix damper servo sub-assembly with the 2 screws.


Hide 87710G 4.INSTALL QUICK HEATER ASSEMBLY (w/ PTC Heater)

a.
E287807

Install the quick heater assembly with the 2 screws.


b.
E287809

Engage the 2 claws to install the quick heater bracket.


c.
E285712

Engage the clamp.


d.
E285710

Install the screw.


Hide 88897P 5.INSTALL ASPIRATOR (for Manual Air Conditioning System)

a.
E285707

Engage the 2 claws to install the aspirator.


Hide 88897P 6.INSTALL ASPIRATOR (for Automatic Air Conditioning System)

a.
E285708

Engage the 2 claws.


b.

Engage the clamp to install the aspirator.


Hide 87201F 7.INSTALL NO. 3 AIR DUCT SUB-ASSEMBLY

a.
E285706

Engage the guide and 2 claws to install the No. 3 air duct sub-assembly as shown in the illustration.


Hide 55835A 8.INSTALL CENTER HEATER TO REGISTER DUCT

a.
E285704

Engage the 4 claws to install the center heater to register duct.


Hide 88501 10.INSTALL NO. 1 COOLER EVAPORATOR SUB-ASSEMBLY

a.

Sufficiently apply compressor oil to 2 new O-rings and the fitting surfaces of the No. 1 cooler evaporator sub-assembly.

Compressor Oil:

ND-OIL 8 or equivalent



b.
E285703

Install the 2 O-rings to the No. 1 cooler evaporator sub-assembly.

NOTICE:

Keep the O-rings and O-ring fitting surfaces free from dirt and foreign matter.



c.
E285702

Engage the clamp and install the No. 1 cooler evaporator sub-assembly with No. 1 cooler thermistor.


Hide 87050 11.INSTALL AIR CONDITIONING RADIATOR ASSEMBLY

a.
E285700

Engage the 5 claws.


b.

Engage the guide and connect the wire harness.


c.
E285698

Install the air conditioning radiator assembly to the blower assembly with cooler evaporator sub-assembly with the 6 screws.


Hide 88515 12.INSTALL COOLER EXPANSION VALVE

a.
E285697

Using a 4 mm hexagon wrench, install the cooler expansion valve with the 2 hexagon bolts.

Torque:
3.5 N*m (36 kgf*cm, 31 in.*lbf)


Hide 82210K 13.INSTALL AIR CONDITIONING HARNESS ASSEMBLY

a.

for LHD:

i.

Engage each clamp to install air conditioning harness assembly.

E285695


ii.

Connect each connector.



b.

for RHD:

i.

Engage each clamp to install the air conditioning harness assembly.

E285696
3.604,3.031 3.844,3.24 0.24,0.208 12 true *A
*A for Automatic Air Conditioning System - -



ii.

Connect each connector.