1. PRECAUTION
Be sure to read Precaution thoroughly before servicing.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
67914
3.REMOVE FRONT DOOR SCUFF PLATE
62112A
4.REMOVE COWL SIDE TRIM SUB-ASSEMBLY
5.DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP
Disconnect the front door opening trim weatherstrip to the extent that allows the removal of the instrument panel finish panel end.
55436A
6.REMOVE INSTRUMENT PANEL FINISH PANEL END
55606
7.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
53601
8.DISCONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY
55045
9.REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY
73900
10.REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (for LHD)
When storing the lower No. 1 instrument panel airbag assembly, keep the airbag deployment side facing upward.
Check that the ignition switch is off.
Check that the cable is disconnected from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
| *a | Hook |
| *b | Clamp |
Remove the 4 bolts.
Disengage the 2 clamps and 3 hooks to separate the lower No. 1 instrument panel airbag assembly.
When separating the lower No. 1 instrument panel airbag assembly, do not pull the airbag wire harness.
| *1 | DLC3 |
| *a | Protective Tape |
| *b | Airbag Connector |
| *c | Airbag Connector Lock |
Disengage the 2 claws and clamp to disconnect the DLC3.
Using a screwdriver with its tip wrapped with protective tape, release the airbag connector lock.
Disconnect the airbag connector to remove the lower No. 1 instrument panel airbag assembly.
When disconnecting any airbag connector, take care not to damage the airbag wire harness.
73900
11.REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (for RHD)
When storing the lower No. 1 instrument panel airbag assembly, keep the airbag deployment side facing upward.
Check that the ignition switch is off.
Check that the cable is disconnected from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
| *a | Hook |
| *b | Clamp |
Remove the 4 bolts.
Disengage the 2 clamps and 3 hooks to separate the lower No. 1 instrument panel airbag assembly.
When separating the lower No. 1 instrument panel airbag assembly, do not pull the airbag wire harness.
| *1 | DLC3 |
| *a | Protective Tape |
| *b | Airbag Connector |
| *c | Airbag Connector Lock |
Disengage the 2 claws and clamp to disconnect the DLC3.
Using a screwdriver with its tip wrapped with protective tape, release the airbag connector lock.
Disconnect the airbag connector to remove the lower No. 1 instrument panel airbag assembly.
When disconnecting any airbag connector, take care not to damage the airbag wire harness.