Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › FRONT PASSENGER AIRBAG ASSEMBLY
RM3160E _58 Vehicle Interior _019710 SUPPLEMENTAL RESTRAINT SYSTEMS _0109988 FRONT PASSENGER AIRBAG ASSEMBLY A

SUPPLEMENTAL RESTRAINT SYSTEMS  FRONT PASSENGER AIRBAG ASSEMBLY  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

CAUTION:

Be sure to read Precaution thoroughly before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 55434F 2.REMOVE CENTER LOWER INSTRUMENT PANEL FINISH PANEL

Hide 82142A 3.DISCONNECT NO. 2 INSTRUMENT PANEL WIRE

a.

Check that the ignition switch is off.


b.

Check that the cable is disconnected from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.
B355780C01
0.51,2.823 0.51,3.052 0.51,3.052 1.802,3.052 true 1.615,2.865 1.615,3.052 true 1.823,2.927 2.135,3.083 0.313,0.156 10 false *a
*a Slider


Slide the slider to release the lock, and then disconnect the connector.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.



Hide 4.REMOVE INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY

Hide 55846A 5.REMOVE NO. 4 HEATER TO REGISTER DUCT

Hide 73960A 6.REMOVE INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY

CAUTION:

When storing the instrument panel passenger airbag assembly, keep the airbag deployment side facing upward.


a.
B355782

Remove the 2 screws.


b.
B355783

Lean the instrument panel safety pad sub-assembly and disengage the 3 hooks.


c.
B355784

Disengage the 3 hooks to remove the instrument panel passenger airbag assembly from the instrument panel safety pad sub-assembly.


Hide 82142A 7.REMOVE NO. 2 INSTRUMENT PANEL WIRE

a.
B355785C01
1.719,1.24 1.115,0.792 1.115,0.792 0.875,0.792 true 1.917,1.458 2.417,1.458 true 0.865,1.635 1.365,1.635 true 0.792,2.625 1.24,3 1.24,3 1.469,3 true 0.708,0.688 1.021,0.844 0.313,0.156 10 false *a 1.49,2.896 1.802,3.052 0.313,0.156 10 false *c 0.677,1.531 0.885,1.719 0.208,0.188 10 true *b 2.438,1.354 2.646,1.542 0.208,0.188 10 true *b
*a Protective Tape
*b Airbag Connector
*c Airbag Connector Lock


Using a screwdriver with its tip wrapped with protective tape, release the 2 airbag connector locks.


b.

Disconnect the 2 airbag connectors to remove the No. 2 instrument panel wire from the instrument panel passenger airbag assembly.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.