Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › CURTAIN SHIELD AIRBAG ASSEMBLY
RM3160E _58 Vehicle Interior _019710 SUPPLEMENTAL RESTRAINT SYSTEMS _0109989 CURTAIN SHIELD AIRBAG ASSEMBLY A

SUPPLEMENTAL RESTRAINT SYSTEMS  CURTAIN SHIELD AIRBAG ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

CAUTION:

Be sure to read Precaution thoroughly before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.REMOVE ROOF HEADLINING ASSEMBLY

Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 4.DISCONNECT SLIDING ROOF DRAIN HOSE (for Sliding Roof)

Hide 62972C 5.REMOVE NO. 1 ROOF SIDE AIR DUCT (for Normal Roof)

B355794N01
0.448,0.771 0.604,0.969 0.156,0.198 10 true A 2.24,0.51 2.396,0.708 0.156,0.198 10 true A 3.125,0.844 3.281,1.042 0.156,0.198 10 true B

a.

Remove the 2 clips (A).


b.

Disengage the clip (B) and remove the No. 1 roof side air duct.


Hide 62972C 6.REMOVE NO. 1 ROOF SIDE AIR DUCT (for Sliding Roof)

a.
B355795N01
0.427,0.688 0.583,0.885 0.156,0.198 10 true A 3.125,0.854 3.281,1.052 0.156,0.198 10 true B

Remove the clip (A).


b.

Disengage the clip (B) and remove the No. 1 roof side air duct.


Hide 62180A 7.REMOVE CURTAIN SHIELD AIRBAG ASSEMBLY

CAUTION:

When storing the curtain shield airbag assembly, keep the airbag deployment side facing upward.


NOTICE:

When removing the curtain shield airbag assembly, have assistants hold it to prevent it from bending.


a.

Check that the ignition switch is off.


b.

Check that the cable is disconnected from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.
B355797C01
0.99,1.948 0.99,1.781 0.99,1.781 0.51,1.781 true 0.979,0.594 0.625,0.594 true 1.01,2.167 0.438,2.167 true 0.344,1.688 0.51,1.927 0.167,0.24 10 true *a 0.469,0.5 0.781,0.656 0.313,0.156 10 false *b 0.219,2.073 0.417,2.26 0.198,0.188 10 true *c
*a Airbag Connector
*b Airbag Connector Lock
*c Protective Tape


Using a screwdriver with its tip wrapped with protective tape, release the airbag connector lock and disconnect the airbag connector.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.



d.
B355799

Disengage the 3 clamps to disconnect the airbag wire harness.


e.

Using needle nose pliers, remove the 9 pins from the 9 clips.

NOTICE:

Do not damage the pins.


B355800C01
2.219,1.917 2.542,1.917 false 2.302,2.271 2.563,2.271 false 4.073,1.76 4.333,1.76 false 3.771,2.417 4,2.417 4,2.417 4.219,2.26 false 6.385,0.375 7.042,0.375 7.042,0.375 7.042,1.167 false 6.5,0.802 6.5,0.375 false 2.563,1.844 2.875,2 0.313,0.156 10 false *1 3.615,2.333 3.823,2.51 0.208,0.177 10 false *2 2.583,2.177 2.896,2.333 0.313,0.156 10 false *a 6.219,0.292 6.406,0.458 0.188,0.167 10 true *b 3.927,1.667 4.24,1.823 0.313,0.156 10 false *a
*1 Pin *2 Spacer
*a Clip *b Spacer Location



f.

Using 2 screwdrivers, disengage the 2 claws of each clip and separate the 9 clips from the vehicle body as shown in the illustration.

HINT:

Remove the 9 clips and curtain shield airbag assembly from the vehicle body as a unit.



g.

While holding the curtain shield airbag assembly, remove the 5 bolts and disengage the 2 clips.


h.

Disengage the 2 hooks to remove the curtain shield airbag assembly.


i.

Remove the 9 clips and 2 spacers from the curtain shield airbag assembly.