Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › SIDE AIRBAG SENSOR
RM3160E _58 Vehicle Interior _019710 SUPPLEMENTAL RESTRAINT SYSTEMS _0109994 SIDE AIRBAG SENSOR A

SUPPLEMENTAL RESTRAINT SYSTEMS  SIDE AIRBAG SENSOR  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 89860A 1.INSTALL SIDE AIRBAG SENSOR ASSEMBLY

a.

Check that the ignition switch is off.


b.

Check that the cable is disconnected from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Before connecting the connector, check that the position of the white housing lock is correct as shown in the illustration.

B296256C01
5.01,0.51 5.302,0.781 0.292,0.271 10 *b 1.792,0.51 2.083,0.802 0.292,0.292 10 *a
*a Correct *b Incorrect



d.

Insert the side airbag sensor assembly pin (stopper) into the body hole and install the side airbag sensor assembly to the vehicle body with the bolt.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)

NOTICE:
·

If the side airbag sensor assembly has been dropped, or there are any cracks, dents or other defects in the case or connector, replace it with a new one.

·

When installing the side airbag sensor assembly, be careful that the SRS wiring does not interfere with or is not pinched between other parts.

·

Make sure that the side airbag sensor assembly pin (stopper) is securely inserted into the body hole.

·

Tighten the bolt while holding the side airbag sensor assembly because the side airbag sensor assembly pin (stopper) is easily damaged.




e.

Connect the connector to the side airbag sensor assembly.

NOTICE:

When connecting any airbag connector, take care not to damage the airbag wire harness.


i.

Be sure to engage the connector until it is locked (when locking, make sure that a click sound can be heard).

C198070C15
3.719,1.219 4.156,1.583 true 1.51,0.927 0.99,0.531 true 3.479,1.146 2.958,0.75 true 5.875,1.448 6.313,1.813 true 4.177,1.604 4.354,1.771 0.177,0.167 10 false *a 3.573,1.74 3.76,1.885 0.188,0.146 10 false *b 6.354,1.833 6.542,1.979 0.188,0.146 10 false *a 0.854,0.438 1.146,0.656 0.292,0.219 10 false A 2.813,0.635 3.104,0.854 0.292,0.219 10 false A
*a White Housing Lock *b Engage


HINT:

When engaged, the white housing lock will slide. Be sure not to hold the white housing lock or part (A), as it may result in an insecure fit.




f.

Check that there is no looseness in the installed parts of the side airbag sensor assembly.


Hide 62414A 2.INSTALL LOWER CENTER PILLAR GARNISH

Hide 3.CONNECT REAR DOOR OPENING TRIM WEATHERSTRIP

Hide 67918A 4.INSTALL REAR DOOR SCUFF PLATE

Hide 72138M 5.INSTALL REAR OUTER SEAT TRACK BRACKET COVER

Hide 6.CONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP

Hide 67914 7.INSTALL FRONT DOOR SCUFF PLATE

Hide 8.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION