Home › Engine / Hybrid System › CRUISE CONTROL › LANE DEPARTURE ALERT SYSTEM › 2013.12–2016.11
RM3160E _51 Engine / Hybrid System _019684 CRUISE CONTROL _0110063 LANE DEPARTURE ALERT SYSTEM C

CRUISE CONTROL  LANE DEPARTURE ALERT SYSTEM  C1AA4  Yaw Rate Sensor Circuit  C1AA5  Yaw Rate Sensor Power Supply Voltage Circuit  C1AA6  Yaw Rate Sensor Zero Point Malfunction  


DESCRIPTION

The skid control ECU (brake actuator assembly) receives vehicle stability signals from the yaw rate sensor (airbag sensor assembly) and sends the signals to the lane departure warning camera. If the skid control ECU (brake actuator assembly) or yaw rate sensor (airbag sensor assembly) detects that the yaw rate sensor is malfunctioning, the skid control ECU (brake actuator assembly) or yaw rate sensor (airbag sensor assembly) sends a malfunction signal to the lane departure warning camera and the lane departure warning camera stores DTC C1AA4, C1AA5 or C1AA6.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1AA4 Yaw Rate Sensor Circuit
·

2 seconds or more have elapsed after the engine switch is turned on (IG).

·

IG voltage is 10 V or more.

·

IG voltage is 10 V or more for 2 seconds or more.

·

While driving with the lane departure alert system operating, a yaw rate sensor malfunction signal sent from the yaw rate sensor (airbag sensor assembly) to the lane departure warning camera is detected for 5 seconds or more.


·

Airbag system

·

Vehicle stability control system

·

Lane departure warning camera

·

Yaw rate sensor (airbag sensor assembly)


C1AA5 Yaw Rate Sensor Power Supply Voltage Circuit
·

2 seconds or more have elapsed after the engine switch is turned on (IG).

·

IG voltage is 10 V or more.

·

IG voltage is 10 V or more for 2 seconds or more.

·

While driving with the lane departure alert system operating, a yaw rate sensor power supply voltage malfunction signal sent from the yaw rate sensor (airbag sensor assembly) to the lane departure warning camera is detected for 5 seconds or more.


·

Airbag system

·

Vehicle stability control system

·

Lane departure warning camera

·

Yaw rate sensor (airbag sensor assembly)


C1AA6 Yaw Rate Sensor Zero Point Malfunction
·

2 seconds or more have elapsed after the engine switch is turned on (IG).

·

IG voltage is 10 V or more.

·

IG voltage is 10 V or more for 2 seconds or more.

·

While driving with the lane departure alert system operating, a yaw rate sensor zero point malfunction signal sent from the skid control ECU (brake actuator assembly) to the lane departure warning camera is detected for 5 seconds or more.


·

Airbag system

·

Vehicle stability control system

·

Lane departure warning camera



CAUTION / NOTICE / HINT

NOTICE:
·

When the lane departure warning camera is replaced with a new one, adjustment of the lane departure warning camera axis must be performed.

Click hereEngine / Hybrid System>CRUISE CONTROL>LANE RECOGNITION CAMERA SENSOR>ADJUSTMENT

·

The lane departure alert system uses the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the lane departure alert system after confirming that the communication systems are functioning properly.

Click hereEngine / Hybrid System>CRUISE CONTROL>LANE DEPARTURE ALERT SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.CHECK FOR DTCs (AIRBAG SYSTEM)
a.

Check for airbag system DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
Result:
Result Proceed to
Airbag system DTCs are not output A
Airbag system DTCs are output B




A

2.CHECK FOR DTCs (VEHICLE STABILITY CONTROL SYSTEM)

B

2.CHECK FOR DTCs (VEHICLE STABILITY CONTROL SYSTEM)
a.

Check for vehicle stability control system DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Result Proceed to
Vehicle stability control system DTCs are not output A
Vehicle stability control system DTCs are output B




A

3.CHECK FOR DTCs (LANE DEPARTURE ALERT SYSTEM)

B

3.CHECK FOR DTCs (LANE DEPARTURE ALERT SYSTEM)
a.

Clear the DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>LANE DEPARTURE ALERT SYSTEM>DTC CHECK / CLEAR

Chassis > Lane Departure Alert > Clear DTCs
50002 355

b.

Make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.



c.

Check for DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>LANE DEPARTURE ALERT SYSTEM>DTC CHECK / CLEAR

Chassis > Lane Departure Alert > Trouble Codes
50001 355
Result:
Result Proceed to
DTC C1AA4, C1AA5 and C1AA6 are not output A
DTC C1AA4, C1AA5 or C1AA6 is output B




A

B