Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › 2013.12–2016.11
RM3160E _51 Engine / Hybrid System _019684 CRUISE CONTROL _0110870 DYNAMIC RADAR CRUISE CONTROL SYSTEM J

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  Distance Control Switch Circuit  


DESCRIPTION

The vehicle-to-vehicle distance control switch is used to set the distance for vehicle-to-vehicle distance control mode. The vehicle-to-vehicle distance control switch is installed in the steering pad switch assembly. The vehicle-to-vehicle distance set value can be changed by operating the vehicle-to-vehicle distance control switch while the dynamic radar cruise control system is controlling vehicle speed in vehicle-to-vehicle distance control mode.

WIRING DIAGRAM

E259148E23
5.344,2.094 6.625,2.5 1.281,0.406 10 false Driving Support ECU Assembly 5.344,1.938 5.656,2.135 0.313,0.198 10 false F84 5.688,0.625 6.177,0.865 0.49,0.24 10 false SPSW 5.49,0.49 5.667,0.635 0.177,0.146 10 false 6 4.24,0.625 4.521,0.771 0.281,0.146 10 false F61 4.302,0.406 4.479,0.552 0.177,0.146 10 false 12 4.25,1.49 4.521,1.656 0.271,0.167 10 false F61 4.354,1.292 4.458,1.438 0.104,0.146 10 false 2 2.99,0.615 3.188,0.76 0.198,0.146 10 false z4 3.01,0.427 3.115,0.573 0.104,0.146 10 false 4 2.979,1.479 3.219,1.708 0.24,0.229 10 false z4 3,1.281 3.125,1.427 0.125,0.146 10 false 7 3.563,0.5 3.906,0.656 0.344,0.156 10 false DIST 3.198,2.125 4.292,2.448 1.094,0.323 10 false Spiral Cable Sub-assembly 0.104,2.021 2.604,2.729 2.5,0.708 10 false Steering Pad Switch Assembly (Vehicle-to-vehicle Distance Control Switch) 3.542,1.365 3.885,1.521 0.344,0.156 10 false ECC

PROCEDURE

1.READ VALUE USING GTS (MODE CHANGE SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Radar Cruise / Data List.


e.

Check the Data List to confirm function of the vehicle-to-vehicle distance control switch.

Powertrain > Radar Cruise > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
MODE Change Switch Vehicle-to-vehicle distance control switch signal ON or OFF ON: Vehicle-to-vehicle distance control switch on
OFF: Vehicle-to-vehicle distance control switch off
-
Powertrain > Radar Cruise > Data List
Tester Display
MODE Change Switch
50003 239 49
OK:

The display changes in accordance with switch operation.



Result:
Proceed to
OK
NG


f.

Turn the engine switch off.



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT STEERING PAD SWITCH ASSEMBLY
2.INSPECT STEERING PAD SWITCH ASSEMBLY
a.

Inspect the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

3.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NG

REPLACE STEERING PAD SWITCH ASSEMBLY

3.INSPECT SPIRAL CABLE SUB-ASSEMBLY
a.

Inspect the spiral cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - DRIVING SUPPORT ECU ASSEMBLY)

NG

4.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - DRIVING SUPPORT ECU ASSEMBLY)
a.

Disconnect the F61 spiral cable sub-assembly connector.


b.

Disconnect the F84 driving support ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
F61-12 (DIST) - F84-6 (SPSW) Always 3 Ω or less


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
F61-12 (DIST) or F84-6 (SPSW) - Body ground Always 1 MΩ or higher



d.

Reconnect the F84 driving support ECU assembly connector.


e.

Reconnect the F61 spiral cable sub-assembly connector.


Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - DRIVING SUPPORT ECU ASSEMBLY)

5.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - BODY GROUND)
a.

Disconnect the F61 spiral cable sub-assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
F61-2 (ECC) - Body ground Always 3 Ω or less



c.

Reconnect the F61 spiral cable sub-assembly connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - BODY GROUND)