Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM › 2013.12–2016.11
RM3160E _58 Vehicle Interior _019711 PRE-CRASH SAFETY _0110871 PRE-CRASH SAFETY SYSTEM C

PRE-CRASH SAFETY  PRE-CRASH SAFETY SYSTEM  C1A0A  Front Radar Sensor Region Code Mismatch  


DESCRIPTION

The driving support ECU assembly uses the millimeter wave radar sensor assembly to detect obstacles in front of the vehicle.

Based on this information, the driving support ECU assembly sends pre-crash sefety control operation signals.

When the millimeter wave radar sensor assembly is replaced with a new one, it acquires the country specification information from the driving support ECU assembly. Also, when the driving support ECU assembly is replaced with a new one, it receives country specification information from the main body ECU (multiplex network body ECU). When country specification information in the millimeter wave radar sensor assembly, driving support ECU assembly and/or main body ECU (multiplex network body ECU) do not match, DTC C1A0A is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1A0A Front Radar Sensor Region Code Mismatch When the engine switch is on (IG), the country specification information from the driving support ECU assembly and millimeter wave radar sensor assembly do not match for approximately 2 seconds.
·

Millimeter wave radar sensor assembly

·

Main body ECU (multiplex network body ECU)



CAUTION / NOTICE / HINT

NOTICE:

When the millimeter wave radar sensor assembly is replaced with a new one, adjustment of the radar sensor beam axis must be performed.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT


PROCEDURE

1.CHECK FOR DTC (PRE-CRASH 2)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).



d.

Make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.



e.

Enter the following menus: Body Electrical / Pre-Crash 2 / Trouble Codes.


f.

Check for DTCs.

Body Electrical > Pre-Crash 2 > Trouble Codes
50001 220

Result:
Result Proceed to
DTC C1A0A is output A
DTC C1A0A and other DTCs are output B


g.

Turn the engine switch off.



A

2.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

B

2.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY
a.

Replace the millimeter wave radar sensor assembly.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

3.ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY
3.ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY
a.

Perform millimeter wave radar sensor assembly adjustment.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT


Result:
Proceed to
NEXT



NEXT

4.CHECK FOR DTC (PRE-CRASH 2)
4.CHECK FOR DTC (PRE-CRASH 2)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).



d.

Make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.



e.

Enter the following menus: Body Electrical / Pre-Crash 2 / Trouble Codes.


f.

Check for DTCs.

Body Electrical > Pre-Crash 2 > Trouble Codes
50001 220

Result:
Result Proceed to
DTC C1A0A is not output A
DTC C1A0A is output B


g.

Turn the engine switch off.



A

END (MILLIMETER WAVE RADAR SENSOR ASSEMBLY WAS DEFECTIVE)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND DRIVING SUPPORT ECU ASSEMBLY