Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM › 2013.12–2016.11
RM3160E _58 Vehicle Interior _019711 PRE-CRASH SAFETY _0110871 PRE-CRASH SAFETY SYSTEM C

PRE-CRASH SAFETY  PRE-CRASH SAFETY SYSTEM  C1A4A  Skid Control Buzzer Circuit  


DESCRIPTION

Based on pre-crash safety control, the driving support ECU assembly provides warnings to the driver. The driving support ECU assembly does this by sending a request signal to the millimeter wave radar sensor assembly to sound the skid control buzzer assembly.

When the millimeter wave radar sensor assembly detects a malfunction in the skid control buzzer assembly circuit, a malfunction signal is sent to the driving support ECU assembly, and this DTC is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1A4A Skid Control Buzzer Circuit While the engine switch is on (IG), a skid control buzzer assembly circuit malfunction signal is received from the millimeter wave radar sensor assembly for 3 seconds or more.
·

Skid control buzzer assembly

·

Skid control buzzer circuit

·

Millimeter wave radar sensor assembly

·

Driving support ECU assembly



WIRING DIAGRAM

E287462
4.333,1.417 5.646,1.906 1.313,0.49 10 false Driving Support ECU Assembly 2.688,1.427 4.094,2.01 1.406,0.583 10 false Millimeter Wave Radar Sensor Assembly 3.74,3.01 5.26,3.417 1.521,0.406 10 false Lane Departure Warning Camera* 3.021,2.479 3.167,2.667 0.146,0.188 10 false * 0.719,3.427 2.396,3.719 1.677,0.292 10 false : CAN Communication Line 0.25,3.021 2.396,3.365 2.146,0.344 10 false *: w/ Lane Departure Alert System 0.938,1.25 2.198,1.771 1.26,0.521 10 false Skid Control Buzzer Assembly 3.271,0.448 3.688,0.677 0.417,0.229 10 false CA1P 4.365,0.885 4.781,1.115 0.417,0.229 10 false CA1N 3.26,0.906 3.677,1.135 0.417,0.229 10 false CA1N 4.365,0.438 4.781,0.667 0.417,0.229 10 false CA1P 2.844,0.635 3.073,0.854 0.229,0.219 10 false BZ 1.594,0.625 1.823,0.844 0.229,0.219 10 false BZ 3.823,2.375 4.052,2.594 0.229,0.219 10 false BZ 1.198,0.635 1.5,0.854 0.302,0.219 10 false IG1 0.948,1.063 1.25,1.281 0.302,0.219 10 false A59 2.677,1.229 2.979,1.448 0.302,0.219 10 false A3 4.344,1.24 4.646,1.458 0.302,0.219 10 false F84 3.74,2.833 4.042,3.052 0.302,0.219 10 false S4 3.646,2.24 3.813,2.458 0.167,0.219 10 false 8 2.604,0.51 2.771,0.729 0.167,0.219 10 false 10 1.854,0.521 2.021,0.74 0.167,0.219 10 false 1 1.042,0.531 1.208,0.75 0.167,0.219 10 false 2 3.698,0.26 3.865,0.479 0.167,0.219 10 false 3 3.708,0.75 3.875,0.969 0.167,0.219 10 false 2 5.292,0.74 5.479,0.927 0.188,0.188 10 false 17 4.125,0.719 4.354,0.917 0.229,0.198 10 false 18 0.104,0.615 0.729,1.219 0.625,0.604 10 false From IG1 NO. 3 Fuse 6.021,1.427 6.49,1.708 0.469,0.281 10 false ECM 6,1.24 6.302,1.458 0.302,0.219 10 false A43 5.75,0.26 5.99,0.479 0.24,0.219 10 false 13 5.76,0.76 6,0.979 0.24,0.219 10 false 26 5.979,0.417 6.396,0.646 0.417,0.229 10 false CANH 4.896,0.875 5.313,1.104 0.417,0.229 10 false CA2L 4.875,0.427 5.292,0.656 0.417,0.229 10 false CA2H 5.979,0.875 6.396,1.104 0.417,0.229 10 false CANL 4.135,0.24 4.375,0.458 0.24,0.219 10 false 40 5.281,0.24 5.521,0.458 0.24,0.219 10 false 39

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When replacing the driving support ECU assembly, always replace it with a new one. If a driving support ECU assembly which was installed to another vehicle is used, the information stored in the driving support ECU assembly will not match the information from the vehicle. As a result, a DTC may be stored.



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (PCS CRASH ALARM BUZZER, PCS APPROACH ALARM BUZZER)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Pre-Crash 2 / Active Test.


e.

Perform "Active Test" according to the display on GTS.

Body Electrical > Pre-Crash 2 > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
PCS Crash Alarm Buzzer Skid control buzzer assembly ON or OFF Buzzer can be heard
PCS Approach Alarm Buzzer Skid control buzzer assembly ON or OFF Buzzer can be heard
Body Electrical > Pre-Crash 2 > Active Test
Tester Display
PCS Crash Alarm Buzzer
50004 220 5
Body Electrical > Pre-Crash 2 > Active Test
Tester Display
PCS Approach Alarm Buzzer
50004 220 6
OK:

Skid control buzzer assembly sounds.



Result:
Proceed to
OK
NG


f.

Turn the engine switch off.



OK

5.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

NG

2.INSPECT SKID CONTROL BUZZER ASSEMBLY
2.INSPECT SKID CONTROL BUZZER ASSEMBLY
a.

Remove the skid control buzzer assembly.

Click hereEngine / Hybrid System>CRUISE CONTROL>LANE DEPARTURE ALERT BUZZER>REMOVAL


b.

Inspect the skid control buzzer assembly.

Click hereEngine / Hybrid System>CRUISE CONTROL>LANE DEPARTURE ALERT BUZZER>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF SKID CONTROL BUZZER ASSEMBLY)

NG

REPLACE SKID CONTROL BUZZER ASSEMBLY

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF SKID CONTROL BUZZER ASSEMBLY)
a.
B338290
0.542,1.198 0.938,1.458 0.396,0.26 2.396,2 2.146,2 2.146,2 1.875,1.604 true 0.094,0.083 0.427,0.396 0.333,0.313 10 false *a 0.635,1.25 0.99,1.458 0.354,0.208 10 false A59 2.448,1.917 2.896,2.135 0.448,0.219 10 false IG1
*a Front view of wire harness connector
(to Skid Control Buzzer Assembly)


Disconnect the A59 skid control buzzer assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A59-2 (IG1) - Body ground Engine switch on (IG) 11 to 14 V
A59-2 (IG1) - Body ground Engine switch off Below 1 V



c.

Reconnect the A59 skid control buzzer assembly connector.


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (SKID CONTROL BUZZER ASSEMBLY - MILLIMETER WAVE RADAR SENSOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (SKID CONTROL BUZZER ASSEMBLY - BATTERY)

4.CHECK HARNESS AND CONNECTOR (SKID CONTROL BUZZER ASSEMBLY - MILLIMETER WAVE RADAR SENSOR ASSEMBLY)
a.

Disconnect the A59 skid control buzzer assembly connector.


b.

Disconnect the A3 millimeter wave radar sensor assembly connector.


c.

Disconnect the S4 lane departure warning camera connector (w/ Lane Departure Alert System).


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A59-1 (BZ) - A3-10 (BZ) Always Below 1 Ω
A59-1 (BZ) or A3-10 (BZ) - Body ground Always 10 kΩ or higher



e.

Reconnect the S4 lane departure warning camera connector (w/ Lane Departure Alert System).


f.

Reconnect the A3 millimeter wave radar sensor assembly connector.


g.

Reconnect the A59 skid control buzzer assembly connector.


Result:
Proceed to
OK
NG



OK

5.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (SKID CONTROL BUZZER ASSEMBLY - MILLIMETER WAVE RADAR SENSOR ASSEMBLY)

5.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY
a.

Replace the millimeter wave radar sensor assembly with a new one.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY
6.ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY
a.

Perform millimeter wave radar sensor assembly adjustment.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT


Result:
Proceed to
NEXT



NEXT

7.CHECK FOR DTC (PRE-CRASH 2)
7.CHECK FOR DTC (PRE-CRASH 2)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).



d.

Make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.



e.

Enter the following menus: Body Electrical / Pre-Crash 2 / Trouble Codes.


f.

Check for DTCs.

Body Electrical > Pre-Crash 2 > Trouble Codes
50001 220

Result:
Result Proceed to
DTC C1A4A is not output A
DTC C1A4A is output B


g.

Turn the engine switch off.



A

END (MILLIMETER WAVE RADAR SENSOR ASSEMBLY WAS DEFECTIVE)

B