Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM › 2013.12–2016.11
RM3160E _58 Vehicle Interior _019711 PRE-CRASH SAFETY _0110871 PRE-CRASH SAFETY SYSTEM C

PRE-CRASH SAFETY  PRE-CRASH SAFETY SYSTEM  U0235  Lost Communication with Cruise Control Front Distance Range Sensor  U1104  Lost Communication with Driving Support ECU  


DESCRIPTION

The driving support ECU assembly sends vehicle speed and vehicle condition information to the millimeter wave radar sensor assembly. The millimeter wave radar sensor assembly then sends information on the presence, distance, and relative speed of objects ahead to the driving support ECU assembly. The driving support ECU assembly sends this information to the ECM and performs pre-crash safety system operation.

DTC No. Detection Item DTC Detection Condition Trouble Area
U0235 Lost Communication with Cruise Control Front Distance Range Sensor When the engine switch is on (IG), a communication error between the millimeter wave radar sensor assembly and the driving support ECU assembly is detected for approximately 1 second.
·

CAN communication system

·

Millimeter wave radar sensor assembly

·

Driving support ECU assembly


U1104 Lost Communication with Driving Support ECU When the engine switch is on (IG), a communication error between the driving support ECU assembly and the millimeter wave radar sensor assembly is detected for approximately 1 second.
·

CAN communication system

·

Millimeter wave radar sensor assembly

·

Driving support ECU assembly



WIRING DIAGRAM

E287467
2.042,1.375 2.604,1.604 0.563,0.229 10 false DSS-IG 6,0.448 6.302,0.698 0.302,0.25 10 false B 2.802,1.042 3,1.292 0.198,0.25 10 false 5 3.052,1.958 3.51,2.24 0.458,0.281 10 false SGND 2.781,1.833 2.938,2.052 0.156,0.219 10 false 1 3.833,1.26 4.292,1.542 0.458,0.281 10 false CA1P 6,1.281 6.458,1.563 0.458,0.281 10 false CA1P 3.823,1.896 4.281,2.177 0.458,0.281 10 false CA1N 5.99,1.896 6.448,2.177 0.458,0.281 10 false CA1N 4.344,1.094 4.542,1.323 0.198,0.229 10 false 3 4.333,1.688 4.531,1.917 0.198,0.229 10 false 2 5.656,1.042 5.854,1.271 0.198,0.229 10 false 40 5.646,1.656 5.844,1.885 0.198,0.229 10 false 18 5.719,2.396 6.052,2.646 0.333,0.25 10 false F84 5.719,2.583 7.01,3.198 1.292,0.615 10 false Driving Support ECU Assembly 2.917,2.375 3.25,2.625 0.333,0.25 10 false A3 2.917,2.552 4.375,3.219 1.458,0.667 10 false Millimeter Wave Radar Sensor Assembly 1.271,3.427 3.24,3.656 1.969,0.229 10 false : CAN Communication Line 4.021,0.333 5.01,0.771 0.99,0.438 10 false from IG1 NO. 3 Fuse 3.042,1.177 3.344,1.427 0.302,0.25 10 false IGB 5.688,0.333 5.885,0.563 0.198,0.229 10 false 30 0.292,1.146 1.281,1.583 0.99,0.438 10 false from IG1 NO. 3 Relay

CAUTION / NOTICE / HINT

NOTICE:
·

When the millimeter wave radar sensor assembly is replaced with a new one, adjustment of the radar sensor beam axis must be performed.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

When replacing the driving support ECU assembly, always replace it with a new one. If a driving support ECU assembly which was installed to another vehicle is used, the information stored in the driving support ECU assembly will not match the information from the vehicle. As a result, a DTC may be stored.



PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Using the GTS, check if the CAN communication system is functioning normally.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING


Result:
Result Proceed to
CAN communication is normal A
CAN communication is malfunctioning B



A

2.CHECK HARNESS AND CONNECTOR (MILLIMETER WAVE RADAR SENSOR ASSEMBLY POWER SOURCE)

B

2.CHECK HARNESS AND CONNECTOR (MILLIMETER WAVE RADAR SENSOR ASSEMBLY POWER SOURCE)
a.
C268297C42
1.51,0.177 1.844,0.427 0.333,0.25 2.583,0.813 2.313,0.813 2.313,0.813 2,1.156 true 0.083,0.083 0.396,0.24 0.313,0.156 10 false *a 2.656,0.729 3.271,0.927 0.615,0.198 10 false IGB 1.583,0.219 1.896,0.375 0.313,0.156 10 false A3
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)


Disconnect the A3 millimeter wave radar sensor assembly connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A3-5 (IGB) - Body ground Engine switch on (IG) 11 to 14 V



d.

Turn the engine switch off.


e.

Reconnect the A3 millimeter wave radar sensor assembly connector.


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (MILLIMETER WAVE RADAR SENSOR ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (MILLIMETER WAVE RADAR SENSOR ASSEMBLY - BODY GROUND)
a.

Disconnect the A3 millimeter wave radar sensor assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A3-1 (SGND) - Body ground Always Below 1 Ω



c.

Reconnect the A3 millimeter wave radar sensor assembly connector.


Result:
Proceed to
OK
NG



OK

4.CHECK DRIVING SUPPORT ECU ASSEMBLY (B VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (MILLIMETER WAVE RADAR SENSOR ASSEMBLY - BODY GROUND)

4.CHECK DRIVING SUPPORT ECU ASSEMBLY (B VOLTAGE)
a.
E244596C04
1.552,0.417 1.885,0.635 0.333,0.219 2.469,2.469 1.906,2.469 1.906,2.469 1.771,1.927 true 0.167,0.167 0.417,0.333 0.25,0.167 10 false *a 2.51,2.396 2.708,2.604 0.198,0.208 10 false B 1.594,0.438 1.927,0.604 0.333,0.167 10 false F84
*a Front view of wire harness connector
(to Driving Support ECU Assembly)


Disconnect the F84 driving support ECU assembly connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F84-30 (B) - Body ground Engine switch on (IG) 11 to 14 V



d.

Turn the engine switch off.


e.

Reconnect the F84 driving support ECU assembly connector.


Result:
Proceed to
OK
NG



OK

5.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

NG

REPAIR OR REPLACE POWER SOURCE CIRCUIT

5.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY
a.

Replace the millimeter wave radar sensor assembly.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY
6.ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY
a.

Perform millimeter wave radar sensor assembly adjustment.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT


Result:
Proceed to
NEXT



NEXT

7.CHECK FOR DTC (PRE-CRASH 2)
7.CHECK FOR DTC (PRE-CRASH 2)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).



d.

Make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.



e.

Enter the following menus: Body Electrical / Pre-Crash 2 / Trouble Codes.


f.

Check for DTCs.

Body Electrical > Pre-Crash 2 > Trouble Codes
50001 220

Result:
Result Proceed to
DTC U0235 and U1104 are not output A
DTC U0235 or U1104 is output B


g.

Turn the engine switch off.



A

END (MILLIMETER WAVE RADAR SENSOR ASSEMBLY WAS DEFECTIVE)

B