Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM › 2013.12–2016.11
RM3160E _58 Vehicle Interior _019711 PRE-CRASH SAFETY _0110871 PRE-CRASH SAFETY SYSTEM J

PRE-CRASH SAFETY  PRE-CRASH SAFETY SYSTEM  Pre-crash Safety System Cancel Switch Circuit  


DESCRIPTION

The driving support ECU assembly receives a pre-crash safety system on/off signal from the pre-crash safety system cancel switch assembly.

WIRING DIAGRAM

E270542
4.875,2.031 5.271,2.229 0.396,0.198 10 false F84 1.813,1.438 2.156,1.656 0.344,0.219 10 false F27 3.802,0.938 4.365,1.302 0.563,0.365 10 false 1 5.167,0.948 5.375,1.292 0.208,0.344 10 false 5 2.323,0.927 2.781,1.354 0.458,0.427 10 false 2 5.365,1.031 5.813,1.188 0.448,0.156 10 false PBSW 4.865,2.198 6.844,2.479 1.979,0.281 10 false Driving Support ECU Assembly 1.802,1.615 5.01,2.094 3.208,0.479 10 false Pre-crash Safety System Cancel Switch Assembly

CAUTION / NOTICE / HINT

NOTICE:

When replacing the driving support ECU assembly, always replace it with a new one. If a driving support ECU assembly which was installed to another vehicle is used, the information stored in the driving support ECU assembly will not match the information from the vehicle. As a result, a DTC may be stored.


PROCEDURE

1.READ VALUE USING GTS (PCS OFF SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Pre-Crash 2 / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Pre-Crash 2 > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
PCS OFF Switch Pre-crash safety system cancel switch assembly status ON or OFF ON: Pre-crash safety system cancel switch assembly on
OFF: Pre-crash safety system cancel switch assembly off
-
Body Electrical > Pre-Crash 2 > Data List
Tester Display
PCS OFF Switch
50003 220 87
OK:

When the pre-crash safety system cancel switch assembly is operated, the display changes as shown above.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT PRE-CRASH SAFETY SYSTEM CANCEL SWITCH ASSEMBLY
2.INSPECT PRE-CRASH SAFETY SYSTEM CANCEL SWITCH ASSEMBLY
a.

Remove the pre-crash safety system cancel switch assembly.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM CANCEL SWITCH>REMOVAL


b.

Inspect the pre-crash sefety system cancel switch assembly.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM CANCEL SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (DRIVING SUPPORT ECU ASSEMBLY - PRE-CRASH SAFETY SYSTEM CANCEL SWITCH ASSEMBLY)

NG

REPLACE PRE-CRASH SAFETY SYSTEM CANCEL SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (DRIVING SUPPORT ECU ASSEMBLY - PRE-CRASH SAFETY SYSTEM CANCEL SWITCH ASSEMBLY)
a.

Disconnect the F84 driving support ECU assembly connector.


b.

Disconnect the F27 pre-crash safety system cancel switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F84-5 (PBSW) - F27-1 Always Below 1 Ω
F84-5 (PBSW) or F27-1 - Body ground Always 10 kΩ or higher



d.

Reconnect the F27 pre-crash sefety system cancel switch assembly connector.


e.

Reconnect the F84 driving support ECU assembly connector.


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (PRE-CRASH SAFETY SYSTEM CANCEL SWITCH ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (PRE-CRASH SAFETY SYSTEM CANCEL SWITCH ASSEMBLY - BODY GROUND)
a.

Disconnect the F27 pre-crash safety system cancel switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F27-2 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR