Home › Drivetrain › MF1A (TRANSFER / 4WD / AWD) › TRANSFER ASSEMBLY › from 2015.11
RM3160E _52 Drivetrain _019685 MF1A TRANSFER / 4WD / AWD _0107526 TRANSFER ASSEMBLY A

MF1A TRANSFER / 4WD / AWD  TRANSFER ASSEMBLY  REASSEMBLY  


PROCEDURE

Hide 41201L 1.INSTALL REAR TRANSFER DRIVEN PINION BEARING (OUTER RACE)

a.
C155201C02
2.271,0.469 2.031,0.469 2.031,0.469 2.219,0.896 false 0.573,1.063 0.448,1.188 0.448,1.188 0.448,1.604 false 1.76,0.365 2.167,0.615 0.406,0.25 10 false SST 0.385,1.625 0.573,1.802 0.188,0.177 10 false *1
*1 Rear Transfer Driven Pinion Bearing (outer race)


Using SST and a press, install the rear transfer driven pinion bearing (outer race) to the transfer case sub-assembly.

SST
09950-60010  (09951-00620)
09950-70010  (09951-07150)

NOTICE:
·

Keep the transfer case sub-assembly horizontal using wooden blocks, etc.

·

If the rear transfer driven pinion bearing (outer race) is damaged or deformed, replace it with a new one.




b.

Apply gear oil to the rear transfer driven pinion bearing (outer race).


Hide 33309H 2.INSTALL TRANSFER OUTPUT SHAFT WASHER

a.

Apply gear oil to the transfer output shaft washer.


b.

Install the transfer output shaft washer to the transfer case sub-assembly.

NOTICE:

If the transfer output shaft washer is damaged or deformed, replace it with a new one.


HINT:

Install the same transfer output shaft washer as the one removed.



Hide 41201K 3.INSTALL FRONT TRANSFER DRIVEN PINION BEARING

a.

Apply gear oil to the inner surface of the transfer case sub-assembly.


b.
C155190C02
1.021,0.844 0.583,0.771 0.583,0.771 1.052,1.51 true 2.385,2.229 1.719,2.229 false 1.698,2.563 1.906,2.563 1.906,2.563 2.375,2.302 false 2.333,0.667 2.698,0.938 0.365,0.271 10 false *a 0.281,0.635 0.844,0.927 0.563,0.292 10 false SST 0.448,1.865 0.844,2.208 0.396,0.344 10 false *b 1.5,2.167 1.813,2.417 0.313,0.25 10 false *1 1.5,2.5 1.76,2.75 0.26,0.25 10 false *2
*1 Transfer Output Shaft Washer
*2 Front Transfer Driven Pinion Bearing (outer race)
*a Turn
*b Hold


Using SST, install the front transfer driven pinion bearing (outer race) to the transfer case sub-assembly.

SST
09950-60010  (09951-00610, 09951-00620, 09951-00650)
09950-60020  (09951-00680)

NOTICE:
·

If the front transfer driven pinion bearing (outer race) is damaged or deformed, replace it with a new one.

·

When replacing the front transfer driven pinion bearing (outer race), replace both outer and inner races as one set.




c.

Apply gear oil to the front transfer driven pinion bearing (outer race).


d.
C164526N02
2.385,1.167 2.927,1.167 false 3,1.073 3.333,1.26 0.333,0.188 10 false SST

Using SST and a press, install the front transfer driven pinion bearing (inner race) to the driven pinion.

SST
09506-30012  

NOTICE:
·

If the front transfer driven pinion bearing (inner race) is damaged or deformed, replace it with a new one.

·

When replacing the front transfer driven pinion bearing (inner race), replace both outer and inner races as one set.




e.

Apply gear oil to the front transfer driven pinion bearing (inner race).


Hide 4.INSTALL DRIVEN PINION

a.
C050996

Install the driven pinion to the transfer case sub-assembly.


b.
C299236C01
2.583,1.156 3,1.156 false 2.969,1.854 3.063,1.854 false 2.844,1.531 3.031,1.531 false 3.094,1.083 3.406,1.24 0.313,0.156 10 false *1 3.115,1.448 3.427,1.604 0.313,0.156 10 false *2 3.115,1.781 3.427,1.938 0.313,0.156 10 false *3
*1 Transfer Pinion Bearing Spacer
*2 Rear Transfer Driven Pinion Bearing (inner race)
*3 Gear Nut


Apply gear oil to the rear transfer driven pinion bearing (inner race).


c.

Install a new transfer pinion bearing spacer and rear transfer driven pinion bearing (inner race) to the driven pinion.

NOTICE:
·

If the rear transfer driven pinion bearing (inner race) is damaged or deformed, replace it with a new one.

·

When replacing the rear transfer driven pinion bearing (inner race), replace both outer and inner races as one set.



HINT:

Install the transfer pinion bearing spacer with the larger inner diameter facing forward as shown in the illustration.



d.

Apply hypoid gear oil LSD to the threads of a new gear nut and its seating surface.


e.
C315823C02
0.49,1.604 0.49,1.844 0.49,1.844 0.625,1.844 false 0.698,0.563 0.844,0.563 0.844,0.563 1.198,0.875 false 1.844,3 2.156,3.156 0.313,0.156 10 false *a 0.365,0.448 0.677,0.604 0.313,0.156 10 false SST 0.677,1.75 1.146,2.063 0.469,0.313 10 false SST
*a Torque Wrench Fulcrum Length


Using SST, install the gear nut.

SST
09326-20011  
09556-16030  

Torque:
Specified tightening torque:

270 to 420 N*m (2753 to 4283 kgf*cm, 199 to 310 ft.*lbf)


NOTICE:
·

This torque value is effective when SST is parallel to the torque wrench.

·

Do not stake the gear nut until the final preload, tooth contact and backlash adjustments are completed.



HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using SST (fulcrum length of 50 mm (1.97 in.)) + torque wrench (fulcrum length of 1100 mm (3.61 ft.)):

258 to 402 N*m (2631 to 4099 kgf*cm, 190 to 296 ft.*lbf)




Hide 5.ADJUST DRIVEN PINION PRELOAD

a.
C310255C01
0.927,0.927 0.75,0.552 0.75,0.552 0.469,0.552 true 1.729,3.083 2.042,3.24 0.313,0.156 10 false *a 0.125,0.469 0.5,0.667 0.375,0.198 10 false SST
*a Torque Wrench Fulcrum Length


Using SST and a torque wrench, measure the driven pinion preload.

SST
09326-20011  

Preload (at Starting)
Item Preload
New bearing 0.7 to 1.4 N*m (7 to 14 kgf*cm, 6 to 12 in.*lbf)
Reused bearing 0.5 to 0.9 N*m (5 to 9 kgf*cm, 4 to 8 in.*lbf)

NOTICE:

Turn the driven pinion counterclockwise and clockwise several times.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using SST (fulcrum length of 50 mm (1.97 in.)) + torque wrench (fulcrum length of 130 mm (5.12 in.)):

Specified Preload (at Starting)
Item Preload
New bearing 0.5 to 1.0 N*m (5 to 10 kgf*cm, 4 to 9 in.*lbf)
Reused bearing 0.3 to 0.6 N*m (3 to 6 kgf*cm, 3 to 5 in.*lbf)




b.

If the preload is more than the specification, replace the transfer pinion bearing spacer with a new one.


c.

If the preload is not sufficient, adjust the driven pinion by tightening the gear nut 5° to 10° and measuring the preload until the preload is within the specification.


d.

Even if the tightening torque of the gear nut exceeds the specified torque, if the preload is insufficient, loosen the gear nut once and apply rust preventive oil or hypoid gear oil LSD to the gear nut and to the screw or rear transfer driven pinion bearing (inner race) surface of the driven pinion. Then perform the procedure again. If the tightening torque is less than the specified torque, replace the transfer pinion bearing spacer with a new one and adjust it.

NOTICE:

Do not loosen the gear nut to reduce the preload.



Hide 6.INSTALL RING GEAR

a.
SA01143C05
1.104,0.177 1.229,0.177 1.229,0.177 1.5,0.854 false 0.771,0.823 0.823,0.823 false 0.896,0.073 1.469,0.458 0.573,0.385 10 false *a
*a Boiling Water


Heat the ring gear in boiling water.


b.

Secure the transfer ring gear mounting case in a vise using aluminum plates.

NOTICE:
·

Be careful not to damage the transfer ring gear mounting case in the vise.

·

Remove any oil and water from the ring gear contact surface of the transfer ring gear mounting case.

·

Clean the bolt holes in the transfer ring gear mounting case.




c.

Carefully remove the ring gear from the boiling water.

CAUTION:

Make sure to wear protective gloves as the ring gear is extremely hot.



d.
C202225C02
1.594,1.198 1.135,1.813 1.135,1.813 1.583,1.344 false 0.969,1.802 1.156,1.979 0.188,0.177 10 false *a
*a Matchmark


After the moisture on the ring gear has completely evaporated, quickly align the matchmarks and set the ring gear to the transfer ring gear mounting case.

NOTICE:

There is no foreign matter on the contact surfaces of the transfer ring gear mounting case and ring gear.



e.

Apply adhesive to the bolt holes and contact surface of the 12 bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:
·

Apply adhesive after the ring gear has cooled down sufficiently.

·

Make sure to install the bolts immediately after applying adhesive to keep foreign matter away from them.




f.

Install the ring gear with the 12 bolts.

Torque:
98.6 N*m (1005 kgf*cm, 73 ft.*lbf)

NOTICE:
·

Tighten the bolts evenly in a diagonal pattern using several steps.

·

Tighten the bolts after the ring gear has cooled down sufficiently.




Hide 41301H 7.INSTALL RING GEAR MOUNTING CASE BEARING

a.

for LH side:

i.
C180839N01
2.753,0.227 3.097,0.417 0.344,0.19 10 SST 2.456,0.313 2.715,0.313 2.715,0.313 2.488,0.639 false

Using SST and a press, install the ring gear mounting case bearing (inner race) to the transfer ring gear mounting case.

SST
09223-00010  
09726-40010  

NOTICE:
·

If the ring gear mounting case bearing (inner race) is damaged or deformed, replace it with a new one.

·

When replacing the ring gear mounting case bearing (inner race), replace both outer and inner races as one set.




ii.

Install the ring gear mounting case plate washer to the transfer case sub-assembly.

NOTICE:

If the ring gear mounting case plate washer is damaged or deformed, replace it with a new one.


HINT:

Use a new ring gear mounting case plate washer with the same thickness as the one removed when installing the ring gear mounting case bearing (outer race).



iii.
C094036N01
1.313,1.521 0.823,0.729 0.823,0.729 1.396,1.104 false 0.542,0.552 0.844,0.708 0.302,0.156 10 false SST

Using SST and a press, install the ring gear mounting case bearing (outer race) to the transfer case sub-assembly.

SST
09950-60010  (09951-00680)
09950-70010  (09951-07200)

NOTICE:
·

If the ring gear mounting case bearing (outer race) is damaged or deformed, replace it with a new one.

·

When replacing the ring gear mounting case bearing (outer race), replace both outer and inner races as one set.




iv.

Apply gear oil to the ring gear mounting case bearing.



b.

for RH side:

i.
C299872N01
2.604,0.479 2.896,0.219 2.896,0.219 2.458,0.375 true 2.969,0.115 3.427,0.313 0.458,0.198 10 false SST

Using SST and a press, install the ring gear mounting case bearing (inner race) to the transfer ring gear mounting case.

SST
09387-00010  
09950-70010  (09951-07100)

NOTICE:
·

If the ring gear mounting case bearing (inner race) is damaged or deformed, replace it with a new one.

·

When replacing the ring gear mounting case bearing (inner race), replace both outer and inner races as one set.




ii.

Install the ring gear mounting case bearing (outer race) to the transfer ring gear mounting case.

NOTICE:
·

If the ring gear mounting case bearing (outer race) is damaged or deformed, replace it with a new one.

·

When replacing the ring gear mounting case bearing (outer race), replace both outer and inner races as one set.




iii.

Apply gear oil to the ring gear mounting case bearing.



Hide 41319 8.INSTALL TRANSFER RING GEAR MOUNTING CASE

a.
C050974

Install the transfer ring gear mounting case to the transfer case sub-assembly.


Hide 36255 9.INSTALL NO. 1 TRANSFER OUTPUT SHAFT SPACER

a.

Apply gear oil to the No. 1 transfer output shaft spacer.


b.
C299571C01
2.594,1.625 2.896,0.385 2.896,0.385 3.031,0.385 false 2.375,1.344 2.073,0.323 2.073,0.323 1.854,0.323 false 1.938,1.438 1.604,0.563 1.604,0.563 1.375,0.563 true 3.01,1.385 2.75,2.51 2.75,2.51 2.292,1.75 false 1.615,0.26 1.927,0.417 0.313,0.156 10 false *a 2.688,2.604 3,2.76 0.313,0.156 10 false *c 1.146,0.479 1.458,0.635 0.313,0.156 10 false *1 3.115,0.313 3.427,0.469 0.313,0.156 10 false *b
*1 No. 1 Transfer Output Shaft Spacer
*a Cutout
*b Transfer Case Hole
*c Transfer Case Sub-assembly


Align the cutout on the No. 1 transfer output shaft spacer with the transfer case hole to install it as shown in the illustration.


Hide 41301X 10.INSTALL NO. 2 TRANSFER RING GEAR MOUNTING CASE WASHER

a.

Apply gear oil to the No. 2 transfer ring gear mounting case washer.


b.
C052769

Using a brass bar and a hammer, install the No. 2 transfer ring gear mounting case washer to the transfer case sub-assembly.

HINT:

Use a No. 2 transfer ring gear mounting case washer with the same thickness as the one removed.



Hide 11.INSTALL BEARING CAP

a.
C052638

Install the bearing cap to the transfer case sub-assembly with the 2 bolts.

Torque:
63.2 N*m (644 kgf*cm, 47 ft.*lbf)


Hide 12.INSPECT RING GEAR BACKLASH

a.
C052635

Set a dial indicator perpendicular to a ring gear tooth tip.


b.

Secure the driven pinion in place and move the ring gear back and forth to measure the backlash.

Backlash:

0.14 to 0.25 mm (0.00551 to 0.00984 in.)


NOTICE:

Check at least 3 positions on the circumference of the ring gear.



c.
C155215C01
0.833,0.83 1.048,1.021 0.215,0.191 10 *1 1.376,0.916 1.039,0.916 false
*1 Ring Gear Mounting Case Plate Washer


If the backlash is outside the specified range, select a ring gear mounting case plate washer from the table below and install it to meet the specified range.

HINT:

If the backlash is more than specified, select a thinner ring gear mounting case plate washer. If the backlash is less than specified, select a thicker ring gear mounting case plate washer.


Ring Gear Mounting Case Plate Washer Thickness
Mark Thickness mm (in.) Mark Thickness mm (in.)
5Q 1.95 mm (0.0768 in.) 7N 2.67 mm (0.1051 in.)
5R 1.97 mm (0.0776 in.) 7P 2.69 mm (0.1059 in.)
5S 1.99 mm (0.0783 in.) 7Q 2.71 mm (0.1067 in.)
5T 2.01 mm (0.0791 in.) 7R 2.73 mm (0.1075 in.)
5U 2.03 mm (0.0799 in.) 7S 2.75 mm (0.1083 in.)
5V 2.05 mm (0.0807 in.) 7T 2.77 mm (0.1091 in.)
5W 2.07 mm (0.0815 in.) 7U 2.79 mm (0.1098 in.)
5X 2.09 mm (0.0823 in.) 7V 2.81 mm (0.1106 in.)
5Y 2.11 mm (0.0831 in.) 7W 2.83 mm (0.1114 in.)
5Z 2.13 mm (0.0839 in.) 7X 2.85 mm (0.1122 in.)
6F 2.15 mm (0.0846 in.) 7Y 2.87 mm (0.1130 in.)
6G 2.17 mm (0.0854 in.) 7Z 2.89 mm (0.1138 in.)
6H 2.19 mm (0.0862 in.) 8F 2.91 mm (0.1146 in.)
6J 2.21 mm (0.0870 in.) 8G 2.93 mm (0.1154 in.)
6K 2.23 mm (0.0878 in.) 8H 2.95 mm (0.1161 in.)
6L 2.25 mm (0.0886 in.) 8J 2.97 mm (0.1169 in.)
6M 2.27 mm (0.0894 in.) 8K 2.99 mm (0.1177 in.)
6N 2.29 mm (0.0902 in.) 8L 3.01 mm (0.1185 in.)
6P 2.31 mm (0.0909 in.) 8M 3.03 mm (0.1193 in.)
6Q 2.33 mm (0.0917 in.) 8N 3.05 mm (0.1201 in.)
6R 2.35 mm (0.0925 in.) 8P 3.07 mm (0.1209 in.)
6S 2.37 mm (0.0933 in.) 8Q 3.09 mm (0.1217 in.)
6T 2.39 mm (0.0941 in.) 8R 3.11 mm (0.1224 in.)
6U 2.41 mm (0.0949 in.) 8S 3.13 mm (0.1232 in.)
6V 2.43 mm (0.0957 in.) 8T 3.15 mm (0.1240 in.)
6W 2.45 mm (0.0965 in.) 8U 3.17 mm (0.1248 in.)
6X 2.47 mm (0.0972 in.) 8V 3.19 mm (0.1256 in.)
6Y 2.49 mm (0.0980 in.) 8W 3.21 mm (0.1264 in.)
6Z 2.51 mm (0.0988 in.) 8X 3.23 mm (0.1272 in.)
7F 2.53 mm (0.0996 in.) 8Y 3.25 mm (0.1280 in.)
7G 2.55 mm (0.1004 in.) 8Z 3.27 mm (0.1287 in.)
7H 2.57 mm (0.1012 in.) 9D 3.29 mm (0.1295 in.)
7J 2.59 mm (0.1020 in.) 9E 3.31 mm (0.1303 in.)
7K 2.61 mm (0.1028 in.) 9F 3.33 mm (0.1311 in.)
7L 2.63 mm (0.1035 in.) 9G 3.35 mm (0.1319 in.)
7M 2.65 mm (0.1043 in.) 9H 3.37 mm (0.1327 in.)


Hide 13.INSPECT TOOTH CONTACT BETWEEN RING GEAR AND DRIVEN PINION

a.
C052771

Apply a light coat of Prussian blue evenly to both sides of all teeth.


b.

Rotate the ring gear 10 times or more.


c.

Rotate the ring gear to inspect the tooth contact pattern.

C247128C10
0.188,1.073 0.5,1.271 0.313,0.198 10 *a 2.656,0.073 2.969,0.271 0.313,0.198 10 *b 2.688,1.823 3,2.021 0.313,0.198 10 *e 4.917,1.802 5.229,2 0.313,0.198 10 *f 4.833,0.115 5.146,0.313 0.313,0.198 10 *c 3.75,1.438 4.063,1.635 0.313,0.198 10 *d 3.75,3.24 4.063,3.438 0.313,0.198 10 *g
*a Proper Contact *b Heel Contact
*c Face Contact *d Select an adjusting washer that will shift the driven pinion closer to the ring gear (*b, *c)
*e Toe Contact *f Flank Contact
*g Select an adjusting washer that will shift the driven pinion away from the ring gear (*e, *f) - -


NOTICE:

Check at least 4 positions on the circumference of the ring gear.


HINT:

Prussian blue shown in the illustration indicates the tooth contact pattern.



d.
C155217C01
1.24,1.865 1.24,2.625 false 1.146,2.708 1.323,2.927 0.177,0.219 10 false *1
*1 Transfer Output Shaft Washer


If the tooth contact pattern is not correct, select a new transfer output shaft washer that is thicker or thinner as necessary and recheck.

NOTICE:

When the transfer output shaft washer thickness is changed, readjust the backlash.

Click hereDrivetrain>MF1A (TRANSFER / 4WD / AWD)>TRANSFER ASSEMBLY>INSPECTION


Transfer Output Shaft Washer Thickness
Mark Thickness mm (in.) Mark Thickness mm (in.)
ZA 2.00 mm (0.0787 in.) KB 2.38 mm (0.0937 in.)
ZB 2.02 mm (0.0795 in.) LA 2.40 mm (0.0945 in.)
ZC 2.04 mm (0.0803 in.) LC 2.42 mm (0.0953 in.)
ZD 2.06 mm (0.0811 in.) MB 2.44 mm (0.0961 in.)
ZE 2.08 mm (0.0819 in.) NA 2.46 mm (0.0969 in.)
AA 2.10 mm (0.0827 in.) NC 2.48 mm (0.0976 in.)
AC 2.12 mm (0.0835 in.) PB 2.50 mm (0.0984 in.)
BB 2.14 mm (0.0843 in.) QA 2.52 mm (0.0992 in.)
CA 2.16 mm (0.0850 in.) QC 2.54 mm (0.1000 in.)
CC 2.18 mm (0.0858 in.) RA 2.56 mm (0.1008 in.)
DB 2.20 mm (0.0866 in.) RB 2.58 mm (0.1016 in.)
EA 2.22 mm (0.0874 in.) RC 2.60 mm (0.1024 in.)
EC 2.24 mm (0.0882 in.) SA 2.62 mm (0.1031 in.)
FB 2.26 mm (0.0890 in.) SB 2.64 mm (0.1039 in.)
GA 2.28 mm (0.0898 in.) SC 2.66 mm (0.1047 in.)
GC 2.30 mm (0.0906 in.) TA 2.68 mm (0.1055 in.)
HB 2.32 mm (0.0913 in.) TB 2.70 mm (0.1063 in.)
JA 2.34 mm (0.0921 in.) TC 2.72 mm (0.1071 in.)
JC 2.36 mm (0.0929 in.) - -


Hide 14.INSPECT AND ADJUST TOTAL PRELOAD

a.
C310255C01
0.927,0.927 0.75,0.552 0.75,0.552 0.469,0.552 true 1.729,3.083 2.042,3.24 0.313,0.156 10 false *a 0.125,0.469 0.5,0.667 0.375,0.198 10 false SST
*a Torque Wrench Fulcrum Length


C155220C01
1.596,2.322 1.787,2.515 0.192,0.193 10 *1 1.693,2.249 1.693,1.719 1.693,1.719 2.38,0.894 false
*1 No. 2 Transfer Ring Gear Mounting Case Washer


Using SST and a torque wrench, measure the total preload.

SST
09326-20011  

Total Preload (at Starting)
Item Preload
New bearing 0.5 to 0.7 N*m (5 to 7 kgf*cm, 4 to 6 in.*lbf) + Driven pinion preload
Reused bearing 0.4 to 0.5 N*m (4 to 5 kgf*cm, 3.5 to 4.4 in.*lbf) + Driven pinion preload

NOTICE:

Turn the driven pinion counterclockwise and clockwise several times.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using SST (fulcrum length of 50 mm (1.97 in.)) + torque wrench (fulcrum length of 130 mm (5.12 in.)):

Specified Total Preload (at Starting)
Item Preload
New bearing 0.4 to 0.5 N*m (4 to 5 kgf*cm, 3.5 to 4.4 in.*lbf) + Driven pinion preload
Reused bearing 0.25 to 0.38 N*m (3 to 4 kgf*cm, 2 to 3 in.*lbf) + Driven pinion preload



If the preload is outside the specified range, replace the No. 2 transfer ring gear mounting case washer with one that is thicker or thinner as necessary and recheck.

No. 2 Transfer Ring Gear Mounting Case Washer Thickness
Mark Thickness mm (in.) Mark Thickness mm (in.)
G7 2.47 mm (0.0972 in.) M7 3.47 mm (0.1366 in.)
G8 2.49 mm (0.0980 in.) M8 3.49 mm (0.1374 in.)
G9 2.51 mm (0.0988 in.) M9 3.51 mm (0.1382 in.)
H0 2.53 mm (0.0996 in.) N0 3.53 mm (0.1390 in.)
H1 2.55 mm (0.1004 in.) N1 3.55 mm (0.1398 in.)
H2 2.57 mm (0.1012 in.) N2 3.57 mm (0.1406 in.)
H3 2.59 mm (0.1020 in.) N3 3.59 mm (0.1413 in.)
H4 2.61 mm (0.1028 in.) N4 3.61 mm (0.1421 in.)
H5 2.63 mm (0.1035 in.) N5 3.63 mm (0.1429 in.)
H6 2.65 mm (0.1043 in.) N6 3.65 mm (0.1437 in.)
H7 2.67 mm (0.1051 in.) N7 3.67 mm (0.1445 in.)
H8 2.69 mm (0.1059 in.) N8 3.69 mm (0.1453 in.)
H9 2.71 mm (0.1067 in.) N9 3.71 mm (0.1461 in.)
J0 2.73 mm (0.1075 in.) P0 3.73 mm (0.1469 in.)
J1 2.75 mm (0.1083 in.) P1 3.75 mm (0.1476 in.)
J2 2.77 mm (0.1091 in.) P2 3.77 mm (0.1484 in.)
J3 2.79 mm (0.1098 in.) P3 3.79 mm (0.1492 in.)
J4 2.81 mm (0.1106 in.) P4 3.81 mm (0.1500 in.)
J5 2.83 mm (0.1114 in.) P5 3.83 mm (0.1508 in.)
J6 2.85 mm (0.1122 in.) P6 3.85 mm (0.1516 in.)
J7 2.87 mm (0.1130 in.) P7 3.87 mm (0.1524 in.)
J8 2.89 mm (0.1138 in.) P8 3.89 mm (0.1531 in.)
J9 2.91 mm (0.1146 in.) P9 3.91 mm (0.1539 in.)
K0 2.93 mm (0.1154 in.) Q0 3.93 mm (0.1547 in.)
K1 2.95 mm (0.1161 in.) Q1 3.95 mm (0.1555 in.)
K2 2.97 mm (0.1169 in.) Q2 3.97 mm (0.1563 in.)
K3 2.99 mm (0.1177 in.) Q3 3.99 mm (0.1571 in.)
K4 3.01 mm (0.1185 in.) Q4 4.01 mm (0.1579 in.)
K5 3.03 mm (0.1193 in.) Q5 4.03 mm (0.1587 in.)
K6 3.05 mm (0.1201 in.) Q6 4.05 mm (0.1594 in.)
K7 3.07 mm (0.1209 in.) Q7 4.07 mm (0.1602 in.)
K8 3.09 mm (0.1217 in.) Q8 4.09 mm (0.1610 in.)
K9 3.11 mm (0.1224 in.) Q9 4.11 mm (0.1618 in.)
L0 3.13 mm (0.1232 in.) R0 4.13 mm (0.1626 in.)
L1 3.15 mm (0.1240 in.) R1 4.15 mm (0.1634 in.)
L2 3.17 mm (0.1248 in.) R2 4.17 mm (0.1642 in.)
L3 3.19 mm (0.1256 in.) R3 4.19 mm (0.1650 in.)
L4 3.21 mm (0.1264 in.) R4 4.21 mm (0.1657 in.)
L5 3.23 mm (0.1272 in.) R5 4.23 mm (0.1665 in.)
L6 3.25 mm (0.1280 in.) R6 4.25 mm (0.1673 in.)
L7 3.27 mm (0.1287 in.) R7 4.27 mm (0.1681 in.)
L8 3.29 mm (0.1295 in.) R8 4.29 mm (0.1689 in.)
L9 3.31 mm (0.1303 in.) R9 4.31 mm (0.1697 in.)
M0 3.33 mm (0.1311 in.) S0 4.33 mm (0.1705 in.)
M1 3.35 mm (0.1319 in.) S1 4.35 mm (0.1713 in.)
M2 3.37 mm (0.1327 in.) S2 4.37 mm (0.1720 in.)
M3 3.39 mm (0.1335 in.) S3 4.39 mm (0.1728 in.)
M4 3.41 mm (0.1343 in.) S4 4.41 mm (0.1736 in.)
M5 3.43 mm (0.1350 in.) S5 4.43 mm (0.1744 in.)
M6 3.45 mm (0.1358 in.) S6 4.45 mm (0.1752 in.)


b.
C167400

Using a chisel and a hammer, stake the gear nut.


Hide 36113D 15.INSTALL TRANSFER CASE OIL SEAL RH

a.

Using SST and a hammer, install a new transfer case oil seal RH to the transfer case sub-assembly until it reaches the position shown in the illustration.

C427053C01
5.188,1.083 5.24,0.917 5.24,0.917 5.385,0.917 false 6.177,1.083 6.229,0.917 6.229,0.917 6.375,0.917 false 4.979,1.656 4.844,1.656 4.844,1.656 4.844,1.802 false 6,1.656 5.865,1.656 5.865,1.656 5.865,1.802 false 4.833,0.667 5.323,1 0.49,0.333 12 false *A 5.833,0.667 6.333,1 0.5,0.333 12 false *B 4.792,1.802 5.104,1.958 0.313,0.156 10 false *1 2.875,1.469 3.188,1.688 0.313,0.219 10 false *a 5.417,0.833 5.875,1.031 0.458,0.198 10 false SST 6.417,0.833 6.917,1.031 0.5,0.198 10 false SST 5.813,1.802 6.125,1.958 0.313,0.156 10 false *1
*A Type A *B Type B
*1 Transfer Case Oil Seal RH - -
*a Depth - -
V100135

Install in this Direction - -


SST
09950-60010  (09951-00340, 09951-00580, 09952-06010)
09950-70010  (09951-07150)

Standard Depth:

33.5 to 34.5 mm (1.32 to 1.36 in.)


NOTICE:
·

Be sure to install the transfer case oil seal RH in the correct orientation.

·

Make sure that the transfer case oil seal RH is not tilted.

·

Do not tap in the transfer case oil seal RH in too far.




b.

Coat the lip of the transfer case oil seal RH with MP grease.


Hide 36111B 16.INSTALL TRANSFER CASE OIL SEAL

a.
C339757C01
3.031,1.958 2.813,1.958 2.813,1.958 2.708,1.427 true 0.792,1.365 1,0.323 1,0.323 0.698,1.26 true 3.083,1.885 3.396,2.042 0.313,0.156 10 false *1 3.063,1.021 3.375,1.177 0.313,0.156 10 false *a 0.906,0.167 1.344,0.354 0.438,0.188 10 false SST
*1 Transfer Case Oil Seal
*a Depth


Using SST and a hammer, install a new transfer case oil seal to the transfer case sub-assembly until it reaches the position shown in the illustration.

SST
09608-10010  
09950-70010  (09951-07150)

Standard Depth:

9.5 to 10.5 mm (0.374 to 0.413 in.)


NOTICE:
·

Make sure that the transfer case oil seal is not tilted.

·

Do not tap in the transfer case oil seal in too far.




b.

Coat the lip of the transfer case oil seal with MP grease.


Hide 36115C 17.INSTALL TRANSFER EXTENSION HOUSING TYPE T OIL SEAL

a.
C326891C01
0.438,0.167 0.76,0.167 false 1.688,0.677 2.146,0.938 2.146,0.938 2.396,0.938 true 2.313,0.323 2.625,0.479 0.313,0.156 10 false *a 0.104,0.083 0.417,0.24 0.313,0.156 10 false SST 2.479,0.844 2.792,1 0.313,0.156 10 false *1
*1 Transfer Extension Housing Type T Oil Seal
*a Depth


Using SST and a hammer, install a new transfer extension housing type T oil seal to the transfer extension housing sub-assembly until it reaches the position shown in the illustration.

SST
09325-20010  

Standard Depth:

9.8 to 10.6 mm (0.386 to 0.417 in.)


NOTICE:
·

Make sure that the transfer extension housing type T oil seal is not tilted.

·

Do not tap in the transfer extension housing type T oil seal in too far.




b.

Coat the lip of the transfer extension housing type T oil seal with MP grease.


Hide 33146A 18.INSTALL TRANSFER EXTENSION HOUSING DUST DEFLECTOR

a.
C350298C01
0.865,0.76 0.594,0.49 0.594,0.49 1.063,0.583 false 2.063,1.385 2.208,1.083 false 1.948,1.375 2.26,1.531 0.313,0.156 10 false *a 1.938,0.625 2.25,0.781 0.313,0.156 10 false *b 0.292,0.417 0.75,0.615 0.458,0.198 10 false SST
*a Rib
*b Approximately 1 to 2 mm (0.0394 to 0.0787 in.)


Using SST and a press, install a new transfer extension housing dust deflector to the transfer extension housing sub-assembly so that the clearance between the rib of the transfer extension housing sub-assembly and the transfer extension housing dust deflector is approximately 1 to 2 mm (0.0394 to 0.0787 in.).

SST
09950-60020  (09951-01030)
09950-70010  (09951-07150)


b.
C350299C01
0.927,1.156 0.563,0.906 0.563,0.906 1.167,0.99 false 2.177,1.792 2.292,1.479 false 0.26,0.823 0.719,1.021 0.458,0.198 10 false SST 2.094,1.771 2.552,1.969 0.458,0.198 10 false *a 1.792,2.781 2.042,2.979 0.25,0.198 10 false *a 1.167,3.146 1.365,3.323 0.198,0.177 10 true *a 0.354,2.583 0.604,2.781 0.25,0.198 10 false *a
*a Rib


Using SST and a hammer, tap in the transfer extension housing dust deflector until it contacts the rib of the transfer extension housing sub-assembly.

SST
09950-60020  (09951-01030)
09950-70010  (09951-07150)

NOTICE:

Make sure that the transfer extension housing dust deflector evenly contacts the 3 ribs of the transfer extension housing sub-assembly.



Hide 36109 19.INSTALL TRANSFER EXTENSION HOUSING SUB-ASSEMBLY

a.

Remove any FIPG and be careful not to drop oil on the contact surfaces of the transfer extension housing sub-assembly and transfer case sub-assembly.


b.

Degrease the surfaces with a non-residue solvent.


c.
C155207C01
0.594,0.615 0.885,0.615 false 0.396,0.531 0.813,0.719 0.417,0.188 10 false *a
*a FIPG


Apply FIPG to the transfer extension housing sub-assembly.

FIPG:

Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent


NOTICE:
·

Apply FIPG in a continuous line (width 1.2 mm (0.0472 in.)) along the sealing surface of the transfer extension housing sub-assembly.

·

Assemble the transfer extension housing sub-assembly within 10 minutes of FIPG application.




d.
C055358

Install the transfer extension housing sub-assembly to the transfer case sub-assembly with the 4 bolts.

Torque:
25.5 N*m (260 kgf*cm, 19 ft.*lbf)


Hide 36100 20.REMOVE TRANSFER ASSEMBLY

a.

Remove the transfer assembly from the overhaul attachment.


Hide 36111G 21.INSTALL TRANSFER CASE STRAIGHT PIN

a.

Using a plastic hammer, install the 4 transfer case straight pins to the transfer case sub-assembly at the positions shown in the illustration.

C295123C01
2.125,2.094 2.656,2.458 0.531,0.365 10 false *a 5.438,2.104 5.969,2.469 0.531,0.365 10 false *b
*a 10.8 to 11.8 mm (0.425 to 0.465 in.) *b 5.7 to 6.7 mm (0.224 to 0.264 in.)



Hide 36128B 22.INSTALL BREATHER OIL DEFLECTOR

a.
C066130

Install the breather oil deflector to the transfer case cover sub-assembly with the bolt.

Torque:
6.5 N*m (66 kgf*cm, 58 in.*lbf)

NOTICE:

Make sure that the breather oil deflector is installed in the correct direction.



Hide 36102 23.INSTALL TRANSFER CASE COVER SUB-ASSEMBLY

a.

Remove any FIPG and be careful not to drop oil on the contact surfaces of the transfer case cover sub-assembly and transfer case sub-assembly.


b.

Degrease the surfaces with a non-residue solvent.


c.
C246024C01
2,0.51 2.354,0.344 false 2.438,0.219 2.844,0.385 0.406,0.167 10 false *a
*a FIPG


Apply FIPG to the transfer case cover sub-assembly.

FIPG:

Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent


NOTICE:
·

Apply FIPG in a continuous line (width 1.2 mm (0.0472 in.)) along the sealing surface of the transfer case cover sub-assembly.

·

Assemble the transfer case cover sub-assembly within 10 minutes after the FIPG application.




d.
C295124

Install the transfer case cover sub-assembly to the transfer case sub-assembly with the 6 bolts.

Torque:
19.6 N*m (200 kgf*cm, 14 ft.*lbf)


e.
C295128

Install 2 new bolts.

Torque:
19.6 N*m (200 kgf*cm, 14 ft.*lbf)

NOTICE:

Wait for at least 1 hour after installing the transfer case cover sub-assembly before adding transfer oil.



Hide 36111H 24.INSTALL TRANSFER CASE BREATHER PLUG

a.
C155233N03
0.508,1.179 0.85,1.368 0.342,0.19 10 SST 0.863,1.259 1.255,1.259 false

Using SST and a hammer, install a new transfer case breather plug to the transfer case cover sub-assembly.

SST
09612-10093  (09612-10061)


Hide 36114F 25.INSTALL TRANSFER DRAIN PLUG

a.

Install a new gasket to the transfer drain plug.


b.
C141914

Install the transfer drain plug to the transfer case sub-assembly.

Torque:
49 N*m (500 kgf*cm, 36 ft.*lbf)


Hide 36114B 26.INSTALL NO. 1 TRANSFER CASE PLUG

a.
C141905

Install a new gasket to the No. 1 transfer case plug.


b.

Install the No. 1 transfer case plug to the transfer case sub-assembly.

Torque:
49 N*m (500 kgf*cm, 36 ft.*lbf)


Hide 36114H 27.INSTALL NO. 2 TRANSFER CASE PLUG

a.
C141912

Install a new gasket to the No. 2 transfer case plug.


b.

Install the No. 2 transfer case plug to the transfer case sub-assembly.

Torque:
49 N*m (500 kgf*cm, 36 ft.*lbf)


Hide 36100A 28.INSTALL TRANSFER AND TRANSAXLE SETTING STUD BOLT

a.

Install 4 new transfer and transaxle setting stud bolts to the transfer case sub-assembly at the positions shown in the illustration.

C343628C01
4.323,1.021 4.906,1.021 false 4.323,1.698 4.906,1.698 false 4.156,0.906 4.469,1.063 0.313,0.156 10 false *a 4.156,1.604 4.469,1.76 0.313,0.156 10 false *b 5.365,0.969 5.677,1.125 0.313,0.156 10 false *c 5.365,1.615 5.677,1.771 0.313,0.156 10 false *d 5.729,1.24 6.042,1.396 0.313,0.156 10 false *e 2.479,0.531 2.635,0.729 0.156,0.198 10 false B 2.438,1.104 2.594,1.302 0.156,0.198 10 false B 2.448,1.438 2.604,1.635 0.156,0.198 10 true B 2.094,2.083 2.25,2.281 0.156,0.198 10 false A
*a Automatic Transaxle Assembly Side *b Transfer Case Sub-assembly Side
*c 30 mm (1.18 in.) *d 22 mm (0.866 in.)
*e 64 mm (2.52 in.) - -


Torque:
Transfer and Transaxle Setting Stud Bolt (A) : 39.2 N*m (400 kgf*cm, 29 ft.*lbf)
Transfer and Transaxle Setting Stud Bolt (B) : 25 N*m (255 kgf*cm, 18 ft.*lbf)

NOTICE:

Install the sealed side of the transfer and transaxle setting stud bolt to the transfer case sub-assembly.