This circuit detects the state of the windshield wiper switch assembly (front wiper switch and front washer switch) and sends it to the windshield wiper relay assembly.
for LHD
for RHD
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
for LHD:
Disconnect the F64 windshield wiper switch assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F64-2 (+B) - Body ground | Ignition switch off | Below 1 V |
| Ignition switch ON | 11 to 14 V | |
| F64-10 (+B2) - Body ground | Ignition switch off | Below 1 V |
| Ignition switch ON | 11 to 14 V |
for RHD:
Disconnect the F64 windshield wiper switch assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F64-3 (+B) - Body ground | Ignition switch off | Below 1 V |
| Ignition switch ON | 11 to 14 V | |
| F64-5 (+B2) - Body ground | Ignition switch off | Below 1 V |
| Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F65 windshield wiper switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F65-4 (EW) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Windshield Wiper Switch Assembly (Adjusting Ring Position) |
| *a | Component without harness connected
(Windshield Wiper Switch Assembly) |
for LHD:
Remove the windshield wiper switch assembly.
Click hereVehicle Exterior>WIPER / WASHER>WIPER SWITCH>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F64-2 (+B) - F64-3 (+1) | MIST | Below 1 Ω |
| F64-3 (+1) - F64-1 (+S) | OFF | |
| F64-3 (+1) - F64-1 (+S) | AUTO | |
| F64-8 (AUTO) - F64-9 (E) | ||
| F64-2 (+B) - F64-3 (+1) | LO | |
| F64-2 (+B) - F64-4 (+2) | HI |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F65-4 (EW) - F65-7 (WF) | ON | Below 1 Ω |
| F64-5 (WR) - F64-10 (+B2) | ||
| F65-4 (EW) - F65-7 (WF) | OFF | 10 kΩ or higher |
| F64-5 (WR) - F64-10 (+B2) |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F64-6 (VR2) - F64-7 (VR1) | P1 | 209 to 231 Ω |
| P2 | 114 to 126 Ω | |
| P3 | 58.9 to 65.1 Ω | |
| P4 | Below 1 Ω |
*: The rain sensor sensitivity can be adjusted by the windshield wiper switch assembly adjusting ring.
| *1 | Windshield Wiper Switch Assembly (Adjusting Ring Position) |
| *a | Component without harness connected
(Windshield Wiper Switch Assembly) |
for RHD:
Remove the windshield wiper switch assembly.
Click hereVehicle Exterior>WIPER / WASHER>WIPER SWITCH>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F64-3 (+B) - F64-2 (+1) | MIST | Below 1 Ω |
| F64-2 (+1) - F64-4 (+S) | OFF | |
| F64-2 (+1) - F64-4 (+S) | AUTO | |
| F64-7 (AUTO) - F64-6 (E) | ||
| F64-3 (+B) - F64-2 (+1) | LO | |
| F64-3 (+B) - F64-1 (+2) | HI |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F65-7 (EW) - F65-4 (WF) | ON | Below 1 Ω |
| F64-10 (WR) - F64-5 (+B2) | ||
| F65-7 (EW) - F65-4 (WF) | OFF | 10 kΩ or higher |
| F64-10 (WR) - F64-5 (+B2) |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F64-8 (VR2) - F64-9 (VR1) | P1 | 209 to 231 Ω |
| P2 | 114 to 126 Ω | |
| P3 | 58.9 to 65.1 Ω | |
| P4 | Below 1 Ω |
*: The rain sensor sensitivity can be adjusted by the windshield wiper switch assembly adjusting ring.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for LHD:
Disconnect the F79 windshield wiper relay assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F64-1 (+S) - F79-10 (+1) | Always | Below 1 Ω |
| F64-1 (+S) or F79-10 (+1) - Body ground | Always | 10 kΩ or higher |
| F64-9 (E) - F79-5 (CO) | Always | Below 1 Ω |
| F64-9 (E) or F79-5 (CO) - Body ground | Always | 10 kΩ or higher |
| F64-8 (AUTO) - F79-3 (C1) | Always | Below 1 Ω |
| F64-8 (AUTO) or F79-3 (C1) - Body ground | Always | 10 kΩ or higher |
| F64-6 (VR2) - F79-8 (VR2) | Always | Below 1 Ω |
| F64-6 (VR2) or F79-8 (VR2) - Body ground | Always | 10 kΩ or higher |
| F64-7 (VR1) - F79-21 (VR1) | Always | Below 1 Ω |
| F64-7 (VR1) or F79-21 (VR1) - Body ground | Always | 10 kΩ or higher |
for RHD:
Disconnect the F79 windshield wiper relay assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F64-4 (+S) - F79-10 (+1) | Always | Below 1 Ω |
| F64-4 (+S) or F79-10 (+1) - Body ground | Always | 10 kΩ or higher |
| F64-6 (E) - F79-5 (CO) | Always | Below 1 Ω |
| F64-6 (E) or F79-5 (CO) - Body ground | Always | 10 kΩ or higher |
| F64-7 (AUTO) - F79-3 (C1) | Always | Below 1 Ω |
| F64-7 (AUTO) or F79-3 (C1) - Body ground | Always | 10 kΩ or higher |
| F64-9 (VR2) - F79-8 (VR2) | Always | Below 1 Ω |
| F64-9 (VR2) or F79-8 (VR2) - Body ground | Always | 10 kΩ or higher |
| F64-8 (VR1) - F79-21 (VR1) | Always | Below 1 Ω |
| F64-8 (VR1) or F79-21 (VR1) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A39 windshield washer motor and pump assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F65-7 (WF) - F79-25 (W) | Always | Below 1 Ω |
| F65-7 (WF) or F79-25 (W) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for LHD:
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F65-7 (WF) - A39-2 | Always | Below 1 Ω |
| F64-5 (WR) - A39-1 | Always | Below 1 Ω |
| F65-7 (WF) or A39-2 - Body ground | Always | 10 kΩ or higher |
| F64-5 (WR) or A39-1 - Body ground | Always | 10 kΩ or higher |
for RHD:
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F65-7 (WF) - A39-2 | Always | Below 1 Ω |
| F64-10 (WR) - A39-1 | Always | Below 1 Ω |
| F65-7 (WF) or A39-2 - Body ground | Always | 10 kΩ or higher |
| F64-10 (WR) or A39-1 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for LHD:
Disconnect the A32 windshield wiper motor assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F64-3 (+1) - A32-5 (+1) | Always | Below 1 Ω |
| F64-4 (+2) - A32-3 (+2) | Always | Below 1 Ω |
| F64-3 (+1) or A32-5 (+1) - Body ground | Always | 10 kΩ or higher |
| F64-4 (+2) or A32-3 (+2) - Body ground | Always | 10 kΩ or higher |
for RHD:
Disconnect the A32 windshield wiper motor assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F64-2 (+1) - A32-1 (+1) | Always | Below 1 Ω |
| F64-1 (+2) - A32-4 (+2) | Always | Below 1 Ω |
| F64-2 (+1) or A32-1 (+1) - Body ground | Always | 10 kΩ or higher |
| F64-1 (+2) or A32-4 (+2) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for LHD:
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F64-4 (+2) - F79-11 (+2) | Always | Below 1 Ω |
| F64-4 (+2) or F79-11 (+2) - Body ground | Always | 10 kΩ or higher |
for RHD:
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F64-1 (+2) - F79-11 (+2) | Always | Below 1 Ω |
| F64-1 (+2) or F79-11 (+2) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the 4F instrument panel junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A32-2 (B) - 4F-1 | Always | Below 1 Ω |
| A32-2 (B) or 4F-1 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Instrument Panel Junction Block Assembly) |
Remove the instrument panel junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4F-1 - 4F-10 | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for LHD:
Disconnect the 4A instrument panel junction block assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F64-2 (+B) - 4A-10 | Always | Below 1 Ω |
| F64-10 (+B2) - 4A-35 | Always | Below 1 Ω |
| F64-2 (+B) or 4A-10 - Body ground | Always | 10 kΩ or higher |
| F64-10 (+B2) or 4A-35 - Body ground | Always | 10 kΩ or higher |
for RHD:
Disconnect the 4A instrument panel junction block assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F64-3 (+B) - 4A-10 | Always | Below 1 Ω |
| F64-5 (+B2) - 4A-35 | Always | Below 1 Ω |
| F64-3 (+B) or 4A-10 - Body ground | Always | 10 kΩ or higher |
| F64-5 (+B2) or 4A-35 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG