Home › Suspension › FRONT SUSPENSION › FRONT SHOCK ABSORBER › from 2015.11
RM3160E _53 Suspension _019689 FRONT SUSPENSION _0107981 FRONT SHOCK ABSORBER A

FRONT SUSPENSION  FRONT SHOCK ABSORBER  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 48158C 1.INSTALL FRONT LOWER COIL SPRING INSULATOR

a.
C337608C03
2.01,1.01 3.042,1.01 true 1.667,1.115 2.948,1.115 2.948,1.115 2.948,1.01 true 3.094,0.938 3.406,1.094 0.313,0.156 10 false *a
*a Claw
V100135

Positioning Pin


Install the front lower coil spring insulator to the front shock absorber assembly.

NOTICE:
·

When installing the front lower coil spring insulator, fit the insulator to the depression of the spring seat and insert the positioning pin into the hole.

·

When installing the front lower coil spring insulator, make sure that the front lower coil spring insulator does not get caught on the claws of the front shock absorber assembly.




Hide 48331C 2.INSTALL FRONT SPRING BUMPER

a.
C337609

Install the front spring bumper to the front shock absorber assembly.

NOTICE:

Face the smaller diameter end of the front spring bumper downward.



Hide 48132 3.INSTALL FRONT COIL SPRING

a.
C292273N01
2.5,1.396 2.5,1.052 2.5,1.052 2.76,1.052 false 2.792,0.979 3.25,1.177 0.458,0.198 10 false SST

Secure SST in a vise.

SST
09727-00050  
09727-30021  (09727-00010, 09727-00031)


b.
C275706C01
0.323,0.167 0.719,0.563 0.396,0.396 10 false *a 0.354,2.479 0.677,2.781 0.323,0.302 10 false *b
*a Correct
*b Incorrect


Attach the arms of SST to the diameter of the front coil spring.

CAUTION:
·

Make sure that the front coil spring is installed so that the distance between the upper and lower arms of SST is at the maximum.

·

Make sure that the claws of the arms are securely attached.




c.

Using SST, compress the front coil spring.

CAUTION:
·

If the front coil spring bends during compression, immediately stop compression and reinstall SST.

·

Do not excessively compress the front coil spring so that the coils contact each other.

·

Do not use an impact wrench. It will damage SST.




d.
C289377C02
0.354,0.844 0.552,0.844 0.552,0.844 0.781,1.458 true 0.198,0.771 0.51,0.927 0.313,0.156 10 false *a
*a Depression


Install the front coil spring to the front shock absorber assembly.

NOTICE:

Make sure to fit the end of the front coil spring that has the larger diameter into the depression of the front lower coil spring insulator.



Hide 48045A 4.INSTALL FRONT SPRING SEAT SUB-ASSEMBLY WITH INSULATOR

a.
C345017C02
2.417,1.281 3.042,1.552 3.042,1.552 3.125,1.552 true 2.333,1.323 2.917,1.99 2.917,1.99 3.01,1.99 true 3.167,1.469 3.385,1.635 0.219,0.167 10 false *1 3.052,1.906 3.365,2.063 0.313,0.156 10 false *a
*1 Strut Mounting Bearing
*a Top End of the Insulator (Shock Absorber Dust Cover)


Install the front spring seat sub-assembly with insulator to the front shock absorber assembly.

NOTICE:

Make sure that the top end of the insulator (shock absorber dust cover) and the strut mounting bearing are securely attached.



Hide 48609 5.INSTALL FRONT SUSPENSION SUPPORT SUB-ASSEMBLY

a.
C294596C01
2.729,0.302 2.563,0.302 2.563,0.302 2.146,0.646 true 2.76,0.229 3.073,0.385 0.313,0.156 10 false *a
*a Slot
V100135

Outside of the Vehicle


Install the front suspension support sub-assembly as shown in the illustration.

HINT:

Check that the slot on the piston rod and the slot on the front suspension support sub-assembly are aligned.



b.

Temporarily tighten a new front support to front shock absorber nut.


c.
C294598C01
2.063,0.146 2.854,0.354 0.792,0.208 10 false 0° +/- 5°
V100135

Outside of the Vehicle


While aligning the stud bolt of the front suspension support sub-assembly and the front shock absorber lower bracket, remove SST from the front coil spring.

NOTICE:
·

Do not use an impact wrench. It will damage SST.

·

When installing the front suspension support sub-assembly, ensure that any misalignment between the front shock absorber lower bracket and the stud bolt is within +/- 5°. Use the stud bolt that is closest to the outside of the vehicle.




Hide 48045A 6.CONNECT FRONT SPRING SEAT SUB-ASSEMBLY WITH INSULATOR

a.
C345018C02
1.917,1.104 2.844,0.823 2.844,0.823 2.948,0.823 false 1.177,1.073 1.5,1.729 1.5,1.729 1.688,1.115 true 1.438,1.74 1.75,1.896 0.313,0.156 10 false *a 3,0.76 3.313,0.917 0.313,0.156 10 false *1
*1 Front Spring Seat Sub-assembly with Insulator
*a Claw


Connect the end of the insulator of the front spring seat sub-assembly with insulator with the claws of the front shock absorber assembly.

NOTICE:
·

Make sure that the end of the insulator is securely attached to the claws of the front shock absorber assembly.

·

Make sure there is no excessive damage to the bellows of the insulator.

·

Do not allow oil, grease, etc., to contact the insulator.

·

If oil or grease has adhered, wipe clean with a cloth. Do not use an alcohol based cleaner.




Hide 7.INSTALL FRONT SHOCK ABSORBER WITH COIL SPRING

a.
C292268C01
0.552,1.5 0.74,1.688 0.188,0.188 10 true *a 1.927,0.344 2.115,0.531 0.188,0.188 10 true *a
*a Spacer


Install the front shock absorber with coil spring (upper side) with the nut and 2 spacers.

Torque:
85 N*m (867 kgf*cm, 63 ft.*lbf)


b.

Install the front shock absorber with coil spring (lower side) to the steering knuckle with the 2 bolts and 2 nuts.

Torque:
290 N*m (2957 kgf*cm, 214 ft.*lbf)

NOTICE:

While keeping the bolts from rotating, tighten the nuts.


HINT:

The bolts can be installed in either direction, however, make sure that they are both installed in the same direction.



Hide 48810 8.INSTALL FRONT STABILIZER LINK ASSEMBLY

a.

Install the front stabilizer link assembly to the front shock absorber assembly with the nut.

Torque:
74 N*m (755 kgf*cm, 55 ft.*lbf)

HINT:

If the ball joint turns together with the nut, use a 6 mm hexagon wrench to hold the stud bolt.



Hide 89543 9.INSTALL FRONT SPEED SENSOR

a.
C291653C01
2.51,1.792 2.51,1.531 true 2.438,1.792 2.594,1.958 0.156,0.167 10 true *a
*a Sensor Clamp


Install the front speed sensor and front flexible hose to the front shock absorber assembly with the bolt.

Torque:
18.8 N*m (192 kgf*cm, 14 ft.*lbf)

NOTICE:

Do not twist the front speed sensor and front flexible hose when installing them.


HINT:

Install the front speed sensor harness bracket first and then the front flexible hose.



b.

Engage the 2 claws to install the sensor clamp.


Hide 55701J 10.INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD)

a.
C291652N01
1.104,2.656 1.24,2.823 0.135,0.167 10 true A 1.042,2.99 1.177,3.156 0.135,0.167 10 true A 1.354,2.271 1.49,2.438 0.135,0.167 10 true B 0.135,3 0.25,3.167 0.115,0.167 10 true C 3.198,3 3.313,3.167 0.115,0.167 10 true C 1.063,2.135 1.198,2.302 0.135,0.167 10 true B 0.563,2.073 0.698,2.24 0.135,0.167 10 true B 0.229,2.625 0.365,2.792 0.135,0.167 10 true B 2.271,3 2.406,3.167 0.135,0.167 10 true A 2.25,2.688 2.385,2.854 0.135,0.167 10 true A 2,2.271 2.135,2.438 0.135,0.167 10 true B 2.292,2.156 2.427,2.323 0.135,0.167 10 true B 2.781,2.073 2.917,2.24 0.135,0.167 10 true B 3.125,2.615 3.26,2.781 0.135,0.167 10 true B 2.021,0.604 2.156,0.771 0.135,0.167 10 true B 1.094,0.323 1.229,0.49 0.135,0.167 10 true B

Install the outer cowl top panel sub-assembly with the 10 bolts and 6 nuts.

Torque:
Nut (A) : 85 N*m (867 kgf*cm, 63 ft.*lbf)
Bolt (B) : 5.5 N*m (56 kgf*cm, 49 in.*lbf)
Nut (C) : 5.5 N*m (56 kgf*cm, 49 in.*lbf)


b.

Engage the 6 clamps to install the wire harness to the outer cowl top panel sub-assembly.


c.

Connect the connector.


Hide 55701J 11.INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)

a.
C291652N01
1.104,2.656 1.24,2.823 0.135,0.167 10 true A 1.042,2.99 1.177,3.156 0.135,0.167 10 true A 1.354,2.271 1.49,2.438 0.135,0.167 10 true B 0.135,3 0.25,3.167 0.115,0.167 10 true C 3.198,3 3.313,3.167 0.115,0.167 10 true C 1.063,2.135 1.198,2.302 0.135,0.167 10 true B 0.563,2.073 0.698,2.24 0.135,0.167 10 true B 0.229,2.625 0.365,2.792 0.135,0.167 10 true B 2.271,3 2.406,3.167 0.135,0.167 10 true A 2.25,2.688 2.385,2.854 0.135,0.167 10 true A 2,2.271 2.135,2.438 0.135,0.167 10 true B 2.292,2.156 2.427,2.323 0.135,0.167 10 true B 2.781,2.073 2.917,2.24 0.135,0.167 10 true B 3.125,2.615 3.26,2.781 0.135,0.167 10 true B 2.021,0.604 2.156,0.771 0.135,0.167 10 true B 1.094,0.323 1.229,0.49 0.135,0.167 10 true B

Install the outer cowl top panel sub-assembly with the 10 bolts and 6 nuts.

Torque:
Nut (A) : 85 N*m (867 kgf*cm, 63 ft.*lbf)
Bolt (B) : 5.5 N*m (56 kgf*cm, 49 in.*lbf)
Nut (C) : 5.5 N*m (56 kgf*cm, 49 in.*lbf)


b.

Engage the 2 clamps to install the wire harness to the outer cowl top panel sub-assembly.


Hide 48609E 12.FULLY TIGHTEN FRONT SUPPORT TO FRONT SHOCK ABSORBER NUT

a.

Fully tighten the front support to front shock absorber nut.

Torque:
70 N*m (714 kgf*cm, 52 ft.*lbf)

NOTICE:

Perform this step only when the front shock absorber with coil spring has been disassembled.



Hide 13.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 14.INSTALL FRONT WHEEL

Torque:
103 N*m (1050 kgf*cm, 76 ft.*lbf)

Hide 15.STABILIZE SUSPENSION

a.

Lower the vehicle.


b.

Bounce the vehicle up and down several times to stabilize the suspension.


Hide 16.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT