87030A
1.INSTALL REAR COOLING UNIT ASSEMBLY
Engage the guide.
Install the rear cooling unit assembly with the 4 bolts.
Tighten the bolts in the order shown in the illustration to install the rear cooling unit assembly.
Connect the drain cooler hose.
Engage each clamp.
Connect each connector.
87217C
2.INSTALL REAR NO. 5 AIR DUCT
Install the rear No. 5 air duct with the 2 clips.
88576C
3.INSTALL NO. 1 COOLER AIR DUCT
Install the No. 1 cooler air duct.
4.INSTALL COOLER PLATE
Engage the 2 claws to install the cooler plate.
62470A
5.INSTALL INNER ROOF SIDE GARNISH ASSEMBLY RH
Use the same procedure as for the LH side.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION
64730B
6.INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH
66311
7.INSTALL ROPE HOOK
Use the same procedure as for the LH side.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION
64725F
8.INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM HOOK
Use the same procedure as for the LH side.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION
64974
9.INSTALL DECK TRIM POCKET COVER
Use the same procedure as for the LH side.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION
81330
10.INSTALL NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY
88625T
11.INSTALL COOLER (NO. 2 ROOM TEMP. SENSOR) THERMISTOR (w/ Rear Automatic Air Conditioning System)
73560
12.CONNECT REAR NO. 2 SEAT OUTER BELT ASSEMBLY RH
Use the same procedure as for the LH side.
Click hereVehicle Interior>SEAT BELT>REAR NO. 2 SEAT OUTER BELT ASSEMBLY>INSTALLATION
64714H
13.INSTALL NO. 1 DECK SIDE TRIM COVER
73360C
14.CONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY RH
Use the same procedure as for the LH side.
Click hereVehicle Interior>SEAT BELT>REAR NO. 1 SEAT OUTER BELT ASSEMBLY>INSTALLATION
64712F
15.INSTALL FRONT DECK SIDE TRIM COVER RH
Use the same procedure as for the LH side.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION
16.INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH
67917A
17.INSTALL REAR DOOR SCUFF PLATE RH
Use the same procedure as for the LH side.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION
72137S
18.INSTALL REAR OUTER SEAT TRACK BRACKET COVER RH
19.INSTALL REAR NO. 2 SEAT ASSEMBLY
58387B
20.INSTALL REAR FLOOR FINISH PLATE
64993
21.INSTALL REAR DECK FLOOR BOX
64742C
22.INSTALL DECK SIDE TRIM BOX LH
64910J
23.INSTALL TONNEAU COVER ASSEMBLY
58409A
24.INSTALL NO. 3 DECK BOARD SUB-ASSEMBLY
58410B
25.INSTALL DECK BOARD ASSEMBLY
88840D
26.CONNECT NO. 2 AIR CONDITIONING ACCESSORY ASSEMBLY
| *a | View A |
| *b | Marking (Yellow) |
| *c | Outlet Heater Water Hose Installation Angle (30 to 60°) |
| *d | Clip Installation Angle (15 to 75°) |
Connect the outlet heater water hose with the marking within the area shown in the illustration.
Do not apply excessive force to the outlet heater water hose.
Engage the clip within the area shown in the illustration.
| *a | View A |
| *b | Marking (Yellow) |
| *c | Inlet Heater Water Hose Installation Angle (30 to 60°) |
| *d | Clip Installation Angle (15 to 75°) |
Connect the inlet heater water hose with the marking within the area shown in the illustration.
Do not apply excessive force to the inlet heater water hose.
Engage the clip within the area shown in the illustration.
Remove the vinyl tape from the liquid tube.
Sufficiently apply compressor oil to a new O-ring and the fitting surface of the liquid tube.
ND-OIL 8 or equivalent
Install the O-ring to the liquid tube.
Connect the liquid tube.
Remove the vinyl tape from the suction tube.
Sufficiently apply compressor oil to a new O-ring and the fitting surface of the suction tube.
ND-OIL 8 or equivalent
Install the O-ring to the suction tube.
Connect the suction tube.
Rotate the hook connector as shown in the illustration.
Insert the tube joint into the fitting hole securely and tighten the bolt.
58723B
27.INSTALL NO. 1 LUGGAGE COMPARTMENT SIDE COVER PROTECTOR
Install the No. 1 luggage compartment side cover protector with the 3 screws, bolt and clip.
28.ADD ENGINE COOLANT (for 1AR-FE)
29.ADD ENGINE COOLANT (for 2GR-FE)
30.INSPECT FOR COOLANT LEAK (for 1AR-FE)
31.INSPECT FOR COOLANT LEAK (for 2GR-FE)
32.CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT
33.WARM UP ENGINE
34.INSPECT FOR REFRIGERANT LEAK