63310
1.INSTALL ROOF HEADLINING ASSEMBLY
Put the roof headlining assembly into the vehicle through the back door as shown in the illustration.
Do not damage the roof headlining assembly or body interior.
for Roof Side (for Normal Roof):
Install the roof headlining assembly with the 4 clips.
for Roof Side (for Sliding Roof):
Engage the 12 fasteners and install the roof headlining assembly with the 2 clips.
Connect the connector to the sliding roof drive gear sub-assembly.
for Rear Side:
Engage the 3 clips.
for Rear Pillar LH Side (w/o DAB Function):
Engage the clamp and 2 guides.
Install the bolt.
Connect the connector.
for Rear Pillar LH Side (w/ DAB Function):
Engage the 2 clamps and 4 guides.
Install the 2 bolts.
Connect the connector.
for Rear Pillar RH Side:
Connect the rear washer hose assembly.
Engage the 2 clamps and 3 guides.
Install the 2 bolts.
Connect the 2 connectors.
for Front Pillar LH Side (w/o Rear Seat Entertainment System):
Connect the 2 connectors.
Engage the 3 clamps.
for Front Pillar LH Side (w/ Rear Seat Entertainment System):
Connect the 3 connectors.
Engage the 3 clamps.
for Front Pillar RH Side:
Connect the rear washer hose assembly.
Connect the connector.
Engage the 3 clamps.
for Windshield Glass Side:
Connect each connector.
62452C
2.CONNECT REAR ROOF SIDE RAIL GARNISH LH
Engage the 3 clips to connect the rear roof side rail garnish LH as shown in the illustration.
62451C
3.CONNECT REAR ROOF SIDE RAIL GARNISH RH
Use the same procedure as for the LH side.
74348
4.INSTALL VISOR HOLDER
Use the same procedure for the LH side and RH side.
Engage the 2 claws.
Push in the visor holder as shown in the illustration.
74320
5.INSTALL VISOR ASSEMBLY LH
for "TORX" Screw:
Using a T25 "TORX" socket wrench, install the visor assembly LH with the 2 screws.
except "TORX" Screw:
Install the visor assembly LH with the 2 screws.
74325
6.INSTALL VISOR BRACKET COVER (for LH Side)
Engage the 4 claws to install the visor bracket cover.
74310
7.INSTALL VISOR ASSEMBLY RH
Use the same procedure as for the LH side.
74325
8.INSTALL VISOR BRACKET COVER (for RH Side)
Use the same procedure as for the LH side.
74610A
9.INSTALL ASSIST GRIP SUB-ASSEMBLY
Use the same procedure for all assist grip sub-assemblies.
Install the clip to the assist grip.
Use the same procedure for the RH side and LH side.
Temporarily install the assist grip cover LH to the assist grip as shown in the illustration.
Use the same procedure for the RH side and LH side.
Engage the 2 clips to install the assist grip sub-assembly.
Engage the 2 claws to install the assist grip cover LH.
After installing the assist grip cover LH and RH, make sure that the 2 clips on the assist grip sub-assembly are engaged securely.
Use the same procedure for the RH side and LH side.
74620B
10.INSTALL REAR ASSIST GRIP ASSEMBLY
Use the same procedure as for the assist grip sub-assembly.
88576C
11.INSTALL NO. 1 COOLER AIR DUCT
12.INSTALL COOLER PLATE
86680A
13.INSTALL TELEVISION DISPLAY ASSEMBLY (w/ Rear Seat Entertainment System)
86295
14.INSTALL TELEVISION BASE
81260A
15.INSTALL MAP LIGHT ASSEMBLY
89943
16.INSTALL RAIN SENSOR COVER (w/ Rain Sensor)
86466
17.INSTALL LANE DEPARTURE WARNING CAMERA COVER NO.1 (w/ Lane Departure Alert System)
86466
18.INSPECT LANE DEPARTURE WARNING CAMERA COVER NO.1 (w/ Lane Departure Alert System)
89943
19.INSTALL RAIN SENSOR COVER (w/ Lane Departure Alert System)
87834
20.INSTALL INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror)
62480A
21.INSTALL INNER ROOF SIDE GARNISH ASSEMBLY LH
Pass the anchor of the rear No. 2 seat outer belt assembly LH through the inner roof side garnish assembly LH.
Engage the claw and 4 clips to install the inner roof side garnish assembly LH.
62639A
22.INSTALL QUARTER PILLAR GARNISH LH
Pass the anchor of the rear No. 1 seat outer belt assembly LH through the quarter pillar garnish LH.
Engage the claw, 2 clips and guide to install the quarter pillar garnish LH.
64740C
23.INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH
Engage the claw, 10 clips and 2 guides.
Install the deck trim side panel assembly LH with the 3 bolts.
66311
24.INSTALL ROPE HOOK (for LH Side)
Install the 2 rope hooks with the 2 bolts.
Engage the 4 claws as shown in the illustration.
64725F
25.INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM HOOK (for LH Side)
Turn the No. 1 luggage compartment trim hook as shown in the illustration to install it.
64974
26.INSTALL DECK TRIM POCKET COVER (for LH Side)
Engage the 2 claws to install the deck trim pocket cover.
73570
27.CONNECT REAR NO. 2 SEAT OUTER BELT ASSEMBLY LH
64735
28.INSTALL DECK TRIM SIDE SERVICE HOLE COVER
Engage the 2 guides.
Engage the claw to install the deck trim side service hole cover.
64715E
29.INSTALL NO. 2 DECK SIDE TRIM COVER
Engage the 6 claws, clip and 2 guides to install the No. 2 deck side trim cover.
73370C
30.CONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY LH
64713F
31.INSTALL FRONT DECK SIDE TRIM COVER LH
Engage the 2 claws and guide to install the front deck side trim cover LH as shown in the illustration.
62470A
32.INSTALL INNER ROOF SIDE GARNISH ASSEMBLY RH
Use the same procedure as for the LH side.
62638A
33.INSTALL QUARTER PILLAR GARNISH RH
Use the same procedure as for the LH side.
64730B
34.INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH
w/ Rear Automatic Air Conditioning System:
Engage the clamp.
Engage the claw, 10 clips and 2 guides.
Install the deck trim side panel assembly RH with the 3 bolts.
66311
35.INSTALL ROPE HOOK (for RH Side)
Use the same procedure as for the LH side.
64725F
36.INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM HOOK (for RH Side)
Use the same procedure as for the LH side.
64974
37.INSTALL DECK TRIM POCKET COVER (for RH Side)
Use the same procedure as for the LH side.
81330
38.INSTALL NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY
62627D
39.INSTALL SIDE TRIM COVER RH (w/o Rear Automatic Air Conditioning System)
Engage the 4 claws to install the side trim cover RH.
88625T
40.INSTALL COOLER (NO. 2 ROOM TEMP. SENSOR) THERMISTOR (w/ Rear Automatic Air Conditioning System)
73560
41.CONNECT REAR NO. 2 SEAT OUTER BELT ASSEMBLY RH
Use the same procedure as for the LH side.
73297E
42.INSTALL DECK TRIM SIDE BELT HOLE COVER RH
Engage the 2 guides.
Engage the 4 claws to install the deck trim side belt hole cover RH.
64714H
43.INSTALL NO. 1 DECK SIDE TRIM COVER
Engage the 5 claws, clip and 2 guides to install the No. 1 deck side trim cover.
73360C
44.CONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY RH
Use the same procedure as for the LH side.
64712F
45.INSTALL FRONT DECK SIDE TRIM COVER RH
Use the same procedure as for the LH side.
62412
46.INSTALL CENTER PILLAR GARNISH LH
Pass the anchor of the front seat outer belt assembly LH through the center pillar garnish LH.
Engage the 2 clips.
Install the center pillar garnish assembly LH with the screw.
73220
47.CONNECT FRONT SEAT OUTER BELT ASSEMBLY LH
62414A
48.INSTALL LOWER CENTER PILLAR GARNISH LH
Engage the 4 claws and 2 clips to install the lower center pillar garnish LH.
49.INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH
| *a | Alignment Mark (Red) |
|
Flange Position |
Align the alignment mark (red) on the rear door opening trim weatherstrip LH with the flange on the vehicle body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip LH.
After installation, check that the corners fit correctly.
67918A
50.INSTALL REAR DOOR SCUFF PLATE LH
Lift up the rear seat adjusting handle and move the rear No. 1 seat assembly LH to the foremost position.
Engage the 6 claws, 4 clips and 2 guides to install the rear door scuff plate LH.
72138M
51.INSTALL REAR OUTER SEAT TRACK BRACKET COVER LH
62212
52.INSTALL FRONT PILLAR GARNISH LH
Remove the protective cover.
Make sure that the 2 front pillar garnish clips are not damaged.
If a front pillar garnish clip is damaged, replace the front pillar garnish clip with a new one.
Engage the front pillar garnish clip (A) to the front pillar garnish LH.
Engage the front pillar garnish clip (A) so that it faces as shown in the illustration.
| *a | Protective Tape |
| *b | 90° |
Push the front pillar garnish LH in the direction indicated by the arrow (1) shown in the illustration to engage the 2 guides.
Using needle-nose pliers with the tips wrapped with protective tape, bend the end of the front pillar garnish clip (B) in the direction indicated by the arrow (2) shown in the illustration.
Push the front pillar garnish LH in the direction indicated by the arrow (3) shown in the illustration and to engage it to the front pillar garnish clip (B).
Using needle-nose pliers with the tips wrapped with protective tape, rotate the front pillar garnish clip (B) in the direction indicated by the arrow (4) shown in the illustration.
Using needle-nose pliers with the tips wrapped with protective tape, push the front pillar garnish clip (B) in the direction indicated by the arrow (5) and rotate them to the position shown in the illustration.
Make sure that the front pillar garnish clip (B) are positioned as shown in the illustration.
| *a | Front Pillar Garnish Clip (A) |
| *b | Front Pillar Garnish Clip (B) |
Engage the 2 front pillar garnish clips to install the front pillar garnish LH.
Make sure that the curtain shield airbag assembly LH is not pinched.
53.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH
| *a | Alignment Mark (Blue) |
|
Flange Position |
Align the alignment mark (blue) on the weatherstrip with the flange on the vehicle body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip LH.
After installation, check that the corners fit correctly.
62112A
54.INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH
Engage the claw and clip.
Install the cowl side trim sub-assembly LH with the clip.
67914
55.INSTALL FRONT DOOR SCUFF PLATE LH
Engage the 2 guides and 10 claws to install the front door scuff plate LH.
62411
56.INSTALL CENTER PILLAR GARNISH RH
Use the same procedure as for the LH side.
73210
57.CONNECT FRONT SEAT OUTER BELT ASSEMBLY RH
Use the same procedure as for the LH side.
62413A
58.INSTALL LOWER CENTER PILLAR GARNISH RH
Use the same procedure as for the LH side.
59.INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH
| *a | Alignment Mark (Green) |
|
Flange Position |
Align the alignment mark (green) on the weatherstrip with the flange on the vehicle body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip RH.
After installation, check that the corners fit correctly.
67917A
60.INSTALL REAR DOOR SCUFF PLATE RH
Use the same procedure as for the LH side.
72137S
61.INSTALL REAR OUTER SEAT TRACK BRACKET COVER RH
Use the same procedure as for the LH side.
62211
62.INSTALL FRONT PILLAR GARNISH RH
Use the same procedure as for the LH side.
63.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH
| *a | Alignment Mark (Pink) |
|
Flange Position |
Align the alignment mark (pink) on the weatherstrip with the flange on the vehicle body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip RH.
After installation, check that the corners fit correctly.
62111A
64.INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH
Use the same procedure as for the LH side.
67913
65.INSTALL FRONT DOOR SCUFF PLATE RH
Use the same procedure as for the LH side.
66.INSTALL REAR NO. 2 SEAT ASSEMBLY
58387B
67.INSTALL REAR FLOOR FINISH PLATE
Engage the 8 claws, 4 clips and 2 guides to install the rear floor finish plate.
64993
68.INSTALL REAR DECK FLOOR BOX
Engage the 4 claws, 2 clips and 2 guides.
Install the rear deck floor box with the nut.
Fold the rear No. 2 seatback assembly LH and RH forward.
Install the 7 clips.
64742C
69.INSTALL DECK SIDE TRIM BOX LH
Engage the 4 claws, clip and guide to install the deck side trim box LH.
64910J
70.INSTALL TONNEAU COVER ASSEMBLY
Install the tonneau cover assembly.
58409A
71.INSTALL NO. 3 DECK BOARD SUB-ASSEMBLY
Install the No. 3 deck board sub-assembly.
58410B
72.INSTALL DECK BOARD ASSEMBLY
Install the deck board assembly.