Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE ACTUATOR › from 2016.11
RM3160E _54 Brake _019692 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0108076 BRAKE ACTUATOR A

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  BRAKE ACTUATOR  INSTALLATION  


PROCEDURE

Hide 44510 1.INSTALL BRAKE ACTUATOR ASSEMBLY

a.
C365368N01
2.469,0.323 2.625,0.521 0.156,0.198 10 false 1 1.135,0.479 1.26,0.667 0.125,0.188 10 true 2 1.906,1.302 2.031,1.479 0.125,0.177 10 true 3

Install the brake actuator assembly to the brake actuator bracket assembly with the 3 bolts.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)

NOTICE:
·

Do not remove the hole plugs of a new brake actuator assembly before connecting the brake lines because the brake actuator assembly is filled with brake fluid.

·

Do not hold the brake actuator assembly by the connector.

·

Tighten the 3 bolts in the order shown in the illustration.




b.

Engage the 2 claws to install the piping clamp.


Hide 2.INSTALL BRAKE ACTUATOR WITH BRACKET

a.
C365366N01
2.646,1.51 2.76,1.677 0.115,0.167 10 true 1 0.885,1.583 1.01,1.76 0.125,0.177 10 true 2 2.156,1.927 2.281,2.094 0.125,0.167 10 true 3

Engage the claw to temporarily install the brake actuator with bracket.

NOTICE:
·

Do not damage the brake lines.

·

Do not deform the refrigerant lines.

·

Do not hold the brake actuator with bracket by the connector.



HINT:

Install the brake actuator with bracket while avoiding the brake lines and refrigerant lines.



b.

Install the 3 bolts in the order shown in the illustration.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


c.
C365364C01
1.708,1.635 1.708,1.219 true 2.521,1.396 2.219,1.396 2.219,1.396 2.042,1.094 true 2.313,0.313 1.969,0.302 1.969,0.302 1.698,0.698 true 1.042,1.344 1.333,1.344 1.333,1.344 1.542,1.052 true 0.906,0.917 1.417,0.917 true 0.771,0.5 1.031,0.5 1.031,0.5 1.292,0.76 true 2.542,1.313 2.719,1.49 0.177,0.177 10 true *a 2.333,0.24 2.51,0.396 0.177,0.156 10 true *b 1.635,1.646 1.802,1.823 0.167,0.177 10 true *c 0.854,1.271 1.031,1.438 0.177,0.167 10 true *d 0.729,0.833 0.906,1 0.177,0.167 10 true *e 0.625,0.417 0.781,0.594 0.156,0.177 10 true *f
*a for LHD: From 1st Chamber of Brake Master Cylinder Sub-assembly
for RHD: From 2nd Chamber of Brake Master Cylinder Sub-assembly
*b for LHD: From 2nd Chamber of Brake Master Cylinder Sub-assembly
for RHD: From 1st Chamber of Brake Master Cylinder Sub-assembly
*c To Front Wheel Cylinder Assembly RH
*d To Rear Wheel Cylinder Assembly LH
*e To Rear Wheel Cylinder Assembly RH
*f To Front Wheel Cylinder Assembly LH


Temporarily tighten the 6 brake lines to the correct positions on the brake actuator assembly as shown in the illustration.


d.
C365365C01
2.917,2.979 2.719,2.979 2.719,2.979 2.719,2.698 false 1.823,2.99 2.135,3.146 0.313,0.156 10 false *a 2.938,2.906 3.25,3.063 0.313,0.156 10 false *b 1.635,0.219 1.771,0.375 0.135,0.156 10 true A 0.875,0.552 1,0.719 0.125,0.167 10 true B 2.323,1.125 2.458,1.281 0.135,0.156 10 true A 1.031,1.052 1.156,1.219 0.125,0.167 10 true B 1.385,1.365 1.51,1.531 0.125,0.167 10 true B 1.917,1.354 2.042,1.521 0.125,0.167 10 true B
*a Torque Wrench Fulcrum Length
*b Union Nut Wrench


Using a union nut wrench, fully tighten each brake line.

Torque:
Specified tightening torque (A) : 19.5 N*m (199 kgf*cm, 14 ft.*lbf)
Specified tightening torque (B) : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow the brake lines to twist or interfere with other parts or the vehicle body during tightening.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.



HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 20 mm (0.787 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

(A): 17.36 N*m (177 kgf*cm, 13 ft.*lbf)

·

When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

(B): 13.38 N*m (136 kgf*cm, 10 ft.*lbf)




e.
C365363C01
0,0 0,0 false
V113147

Lock the lock lever


Engage the clamp to the brake actuator bracket assembly.


f.

Connect the connector to the brake actuator assembly and lock the lock lever.

NOTICE:
·

Make sure that the connector is locked securely.

·

Make sure that the actuator connector can be connected smoothly. Do not allow water, oil or dirt to enter the connector.




Hide 3.INSTALL AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY

a.

Install the air conditioner tube and accessory assembly with the bolt.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)

NOTICE:
·

Do not deform the refrigerant lines.

·

Do not damage the clamp.




b.

Engage the clamp to install the air conditioner tube and accessory assembly to the piping clamp.

NOTICE:
·

Do not deform the refrigerant lines.

·

Do not damage the clamp.




Hide 88704 4.INSTALL SUCTION HOSE SUB-ASSEMBLY

a.

for 1AR-FE:

i.

Install the suction hose sub-assembly to the brake actuator bracket assembly with the bolt.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)

NOTICE:
·

Do not deform the refrigerant lines.

·

Do not damage the clamp.





b.

for 2GR-FKS:

i.

Install the suction hose sub-assembly to the suction hose clamp and engage the claw.

NOTICE:
·

Do not deform the refrigerant lines.

·

Do not damage the clamp.





c.

Engage the clamp to install the suction hose sub-assembly to the piping clamp.

NOTICE:
·

Do not deform the refrigerant lines.

·

Do not damage the clamp.




Hide 47371B 5.INSTALL NO. 6 BRAKE TUBE CLAMP

a.

Install the No. 6 brake tube clamp with the bolt.

Torque:
4.9 N*m (50 kgf*cm, 43 in.*lbf)


Hide 6.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 7.BLEED BRAKE SYSTEM

Hide 8. PERFORM YAW RATE AND ACCELERATION SENSOR ZERO POINT CALIBRATION AND STORE SYSTEM INFORMATION