Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2016.11
RM3160E _54 Brake _019692 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0106374 VEHICLE STABILITY CONTROL SYSTEM D

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  DTC CHECK / CLEAR  


DTC CHECK/CLEAR (When Using GTS)


a.

Check for DTCs.

i.

Turn the ignition switch off.


ii.

Connect the GTS to the DLC3.


iii.

Turn the ignition switch to ON.


iv.

Turn the GTS on.


v.

Read the DTCs following the prompts on the GTS. Enter the following menus: Chassis / ABS/VSC/TRC / Trouble Codes.

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105



b.

Clear the DTCs.

i.

Turn the ignition switch off.


ii.

Connect the GTS to the DLC3.


iii.

Turn the ignition switch to ON.


iv.

Turn the GTS on.


v.

Operate the GTS to clear the codes. Enter the following menus: Chassis / ABS/VSC/TRC / Trouble Codes.

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

vi.

Press the DTC clear button.




DTC CHECK/CLEAR (When Using SST Check Wire)


a.

Check for DTCs.

i.

Turn the ignition switch off.


ii.
C146309C75
1.365,2.031 1.833,1.49 true 1.656,0.813 2.094,0.313 true 0.104,0.083 0.417,0.354 0.313,0.271 10 *a 2.135,0.188 2.438,0.333 0.302,0.146 10 CG 1.156,1.948 1.458,2.094 0.302,0.146 10 TC
*a Front view of DLC3


Using SST, connect terminals TC and CG of the DLC3.

SST
09843-18040  


iii.

Turn the ignition switch to ON.


iv.

Observe the blinking pattern of the ABS warning and slip indicator lights in order to identify the DTC.

HINT:

If the ABS warning and slip indicator lights do not blink, inspect the TC and CG terminal circuit, and ABS warning and slip indicator light circuits.


Trouble Area See procedure
TC and CG terminal circuit (Click here)
ABS warning light circuit (Remains on) (Click here)
ABS warning light circuit (Does not come on) (Click here)
Slip indicator light circuit (Remains on) (Click here)
Slip indicator light circuit (Does not come on) (Click here)


v.

Count the number of blinks of the ABS warning and slip indicator lights.

HINT:
·

How to read DTCs:

Diagnostic trouble codes are represented by the number of blinks of a warning light. For example, code 21 would be shown by 2 blinks, a pause of 1.5 seconds, and then 1 blink.

·

If one code is detected:

The light repeats the same code after a pause of 4 seconds.

·

If multiple codes are detected:

The light outputs one code after another with a 2.5-second pause between each code.

When all codes have been output, there is a 4-second pause and then the light begins to output the codes again.

·

If more than 1 malfunction is detected at the same time, the lowest numbered code will be displayed first.




vi.

Check the details of the DTCs.

ABS DTC:
ABS Warning Light Display Tester Display
11 C146E
12 C146F
13 C142B
C146C
14 C146D
21 C1468
22 C1469
23 C146A
24 C146B
25 C1225
31 C1401
C1405
32 C1402
C1406
33 C1403
C1407
34 C1404
C1408
35 C1413
36 C1414
37 C1337
38 C1415
39 C1416
41 C120B
C1241
C1417
43 C1232
C1243
44 C1419
C1442
45 C1245
46 C1421
C1422
C1423
C1424
C142A
C1449
49 C1425
C1426
51 C1427
C1428
59 C1203
67 C1429
C1430
C1431
94 U0073
95 U0124
97 C1381
98 C1336

VSC DTC:
Slip Indicator Light Display Tester Display
31 C1432
C1433
C1434
34 C1435
C1436
C1443
36 C1210
63 U0126
64 C1380
65 C1437
U0100
66 C1290
C1439
C1445
98 C1440

*: This DTC is output when the VSC system detects a malfunction in the ABS.



vii.

After completing the check, disconnect terminals TC and CG of the DLC3 to turn off the display.

If 2 or more DTCs are detected at the same time, the DTCs will be displayed in ascending order.



b.

Clear the DTCs.

i.

Turn the ignition switch off.


ii.
C146309C75
1.365,2.031 1.833,1.49 true 1.656,0.813 2.094,0.313 true 0.104,0.083 0.417,0.354 0.313,0.271 10 *a 2.135,0.188 2.438,0.333 0.302,0.146 10 CG 1.156,1.948 1.458,2.094 0.302,0.146 10 TC
*a Front view of DLC3


Using SST, connect terminals TC and CG of the DLC3.

SST
09843-18040  


iii.

Turn the ignition switch to ON.


iv.

Clear the DTCs stored in the ECU by depressing the brake pedal 8 times or more within 5 seconds.


v.

Check that the ABS warning and slip indicator lights indicate the normal system code.


vi.

Remove SST from the terminals of the DLC3.

HINT:

The DTCs cannot be cleared by disconnecting the battery terminal or the fuse.





END OF DTC CHECK/CLEAR


a.

Turn the ignition switch to ON.


b.

Check that the ABS warning and slip indicator lights go off within approximately 3 seconds of turning the ignition switch to ON.