Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM › from 2016.11
RM3160E _56 Audio / Visual / Telematics _019700 AUDIO / VIDEO _0096790 AUDIO AND VISUAL SYSTEM C

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM  B1324  Lost Communication with Meter  


DESCRIPTION

This DTC is stored when a communication error occurs between the radio and display receiver assembly and combination meter assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1324 Lost Communication with Meter After the radio and display receiver assembly receives a registration information signal, which is sent by the combination meter assembly when the ignition switch is turned to ACC, 1 or more times, the radio and display receiver assembly cannot receive the signal for 30 seconds or more
·

Combination meter assembly

·

Radio and display receiver assembly

·

Harness or connector



WIRING DIAGRAM

E361732E01
1.656,0.427 2.24,0.646 0.583,0.219 10 false MSCH 5.104,0.417 5.688,0.635 0.583,0.219 10 false CNH1 4.896,0.25 5.219,0.479 0.323,0.229 10 false 3 4.906,0.917 5.229,1.146 0.323,0.229 10 false 4 2.156,0.938 2.479,1.167 0.323,0.229 10 false 30 2.146,0.281 2.469,0.51 0.323,0.229 10 false 29 0.896,2.229 3.083,2.583 2.188,0.354 10 false : Local Bus Communication Line 0.74,1.573 1.135,1.802 0.396,0.229 10 false F126 0.729,1.719 2.635,2.052 1.906,0.333 10 false Combination Meter Assembly 4.781,1.563 5.104,1.792 0.323,0.229 10 false F72 4.771,1.729 6.458,2.26 1.688,0.531 10 false Radio and Display Receiver Assembly 1.667,1.083 2.25,1.302 0.583,0.219 10 false MSCL 5.094,1.073 5.677,1.292 0.583,0.219 10 false CNL1

PROCEDURE

1.CHECK DTC (METER / GAUGE SYSTEM)
a.

Check for DTCs and check that no DTCs are output.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR

Body Electrical > Combination Meter > Trouble Codes
50001 122
Result:
Result Proceed to
DTCs are not output. A
DTCs are output. B




A

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY)

B

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the F72 radio and display receiver assembly connector.


b.

Disconnect the F126 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F72-3 (CNH1) - F126-29 (MSCH) Always Below 1 Ω
F72-4 (CNL1) - F126-30 (MSCL) Always Below 1 Ω
F72-3 (CNH1) or F126-29 (MSCH) - Body ground Always 10 kΩ or higher
F72-4 (CNL1) or F126-30 (MSCL) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.REPLACE COMBINATION METER ASSEMBLY
a.

Replace the combination meter assembly.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL


b.

Clear the DTCs.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>DTC CHECK / CLEAR

Body Electrical > Navigation System > Clear DTCs
50002 212

c.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY