If there is a short in a speaker circuit, the radio and display receiver assembly detects it and stops output to the speakers.
Thus sound cannot be heard from the speakers even if there is no malfunction in the radio and display receiver assembly, telematics transceiver* or speakers.
*: w/ Manual (SOS) Switch
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be necessary. Refer to Precaution for Audio and Visual System.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>PRECAUTION
Enter the "System Check Mode" screen. Refer to Check Speaker in Operation Check.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>OPERATION CHECK
Perform the operation check above and determine the speaker that is not operating.
| Not Operating Speaker | Proceed to |
|---|---|
| Front No. 1 speaker assembly or front No. 2 speaker assembly
(w/o Manual (SOS) Switch) |
A |
| Front No. 1 speaker assembly or front No. 2 speaker assembly
(w/ Manual (SOS) Switch) |
B |
| Rear speaker assembly | C |
If sound cannot be heard from any speaker, inspect all of them.
A
B
C
Disconnect the F69 radio and display receiver assembly connector.
Disconnect the H3 and I3 front No. 1 speaker assembly connectors.
Disconnect the G1 and G5 front No. 2 speaker assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F69-1 (FR+) - G1-4 (+) | Always | Below 1 Ω |
| F69-5 (FR-) - G1-2 (-) | Always | Below 1 Ω |
| F69-2 (FL+) - G5-4 (+) | Always | Below 1 Ω |
| F69-6 (FL-) - G5-2 (-) | Always | Below 1 Ω |
| H3-1 - G1-3 (+) | Always | Below 1 Ω |
| H3-2 - G1-1 (-) | Always | Below 1 Ω |
| I3-1 - G5-3 (+) | Always | Below 1 Ω |
| I3-2 - G5-1 (-) | Always | Below 1 Ω |
| F69-1 (FR+) or G1-4 (+) - Body ground | Always | 10 kΩ or higher |
| F69-5 (FR-) or G1-2 (-) - Body ground | Always | 10 kΩ or higher |
| F69-2 (FL+) or G5-4 (+) - Body ground | Always | 10 kΩ or higher |
| F69-6 (FL-) or G5-2 (-) - Body ground | Always | 10 kΩ or higher |
| H3-1 or G1-3 (+) - Body ground | Always | 10 kΩ or higher |
| H3-2 or G1-1 (-) - Body ground | Always | 10 kΩ or higher |
| I3-1 or G5-3 (+) - Body ground | Always | 10 kΩ or higher |
| I3-2 or G5-1 (-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front No. 1 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>REMOVAL
Inspect the front No. 1 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front No. 2 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>REMOVAL
Inspect the front No. 2 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>INSPECTION
Malfunction disappears.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F69 radio and display receiver assembly connector.
Disconnect the G1 and G5 front No. 2 speaker assembly connectors.
Disconnect the F140 telematics transceiver connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F69-1 (FR+) - F140-2 (SPI+) | Always | Below 1 Ω |
| F69-5 (FR-) - F140-3 (SPI-) | Always | Below 1 Ω |
| F140-5 (SPO+) - G1-4 (+) | Always | Below 1 Ω |
| F140-6 (SPO-) - G1-2 (-) | Always | Below 1 Ω |
| F69-2 (FL+) - G5-4 (+) | Always | Below 1 Ω |
| F69-6 (FL-) - G5-2 (-) | Always | Below 1 Ω |
| F69-1 (FR+) or F140-2 (SPI+) - Body ground | Always | 10 kΩ or higher |
| F69-5 (FR-) or F140-3 (SPI-) - Body ground | Always | 10 kΩ or higher |
| F140-5 (SPO+) or G1-4 (+) - Body ground | Always | 10 kΩ or higher |
| F140-6 (SPO-) or G1-2 (-) - Body ground | Always | 10 kΩ or higher |
| F69-2 (FL+) or G5-4 (+) - Body ground | Always | 10 kΩ or higher |
| F69-6 (FL-) or G5-2 (-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H3 and I3 front No. 1 speaker assembly connectors.
Disconnect the G1 and G5 front No. 2 speaker assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H3-1 - G1-3 (+) | Always | Below 1 Ω |
| H3-2 - G1-1 (-) | Always | Below 1 Ω |
| I3-1 - G5-3 (+) | Always | Below 1 Ω |
| I3-2 - G5-1 (-) | Always | Below 1 Ω |
| H3-1 or G1-3 (+) - Body ground | Always | 10 kΩ or higher |
| H3-2 or G1-1 (-) - Body ground | Always | 10 kΩ or higher |
| I3-1 or G5-3 (+) - Body ground | Always | 10 kΩ or higher |
| I3-2 or G5-1 (-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front No. 1 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>REMOVAL
Inspect the front No. 1 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front No. 2 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>REMOVAL
Inspect the front No. 2 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>INSPECTION
Malfunction disappears.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the telematics transceiver.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL
| *a | Component without harness connected
(Telematics Transceiver) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2 (SPI+) - 5 (SPO+) | Always | Below 1 Ω |
| 3 (SPI-) - 6 (SPO-) | Always | Below 1 Ω |
| 2 (SPI+) - 3 (SPI-) | Always | 10 kΩ or higher |
| 5 (SPO+) - 6 (SPO-) | Always | 10 kΩ or higher |
| 2 (SPI+) or 5 (SPO+) - Body ground | Always | 10 kΩ or higher |
| 3 (SPI-) or 6 (SPO-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F70 radio and display receiver assembly connector.
Disconnect the K4 and J4 rear speaker assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F70-1 (RR+) - J4-1 | Always | Below 1 Ω |
| F70-3 (RR-) - J4-2 | Always | Below 1 Ω |
| F70-2 (RL+) - K4-1 | Always | Below 1 Ω |
| F70-6 (RL-) - K4-2 | Always | Below 1 Ω |
| F70-1 (RR+) or J4-1 - Body ground | Always | 10 kΩ or higher |
| F70-3 (RR-) or J4-2 - Body ground | Always | 10 kΩ or higher |
| F70-2 (RL+) or K4-1 - Body ground | Always | 10 kΩ or higher |
| F70-6 (RL-) or K4-2 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the rear speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER>REMOVAL
Inspect the rear speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG