w/o Manual (SOS) Switch:
The radio and display receiver assembly and map light assembly (telephone microphone assembly) are connected to each other using the microphone connection detection signal lines.
Using this circuit, the radio and display receiver assembly sends power to the map light assembly (telephone microphone assembly), and the map light assembly (telephone microphone assembly) sends microphone signals to the radio and display receiver assembly.
w/ Manual (SOS) Switch:
The radio and display receiver assembly and map light assembly (telephone microphone assembly) are connected to each other using the microphone connection detection signal lines.
Using this circuit, the telematics transceiver sends power to the map light assembly (telephone microphone assembly), and the map light assembly (telephone microphone assembly) sends microphone signals to the radio and display receiver assembly via the telematics transceiver.
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be necessary. Refer to Precaution for Audio and Visual System.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>PRECAUTION
Enter the "Microphone Check" screen. Refer to Check Microphone in Operation Check.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>OPERATION CHECK
When a voice is input into the microphone, check that the microphone input level meter changes according to the input voice.
Check result is normal.
| Result | Proceed to |
|---|---|
| NG (w/o Manual (SOS) Switch) | A |
| NG (w/ Manual (SOS) Switch) | B |
| OK | C |
A
B
C
Disconnect the F71 radio and display receiver assembly connector.
Disconnect the S1 map light assembly (telephone microphone assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F71-6 (SNS2) - S1-13 (SNS2) | Always | Below 1 Ω |
| F71-4 (MACC) - S1-3 (MACC) | Always | Below 1 Ω |
| F71-5 (MIN+) - S1-2 (MCO+) | Always | Below 1 Ω |
| F71-19 (MIN-) - S1-4 (MCO-) | Always | Below 1 Ω |
| F71-6 (SNS2) or S1-13 (SNS2) - Body ground | Always | 10 kΩ or higher |
| F71-4 (MACC) or S1-3 (MACC) - Body ground | Always | 10 kΩ or higher |
| F71-5 (MIN+) or S1-2 (MCO+) - Body ground | Always | 10 kΩ or higher |
| F71-19 (MIN-) or S1-4 (MCO-) - Body ground | Always | 10 kΩ or higher |
| F71-18 (SGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the F71 radio and display receiver assembly connector.
Reconnect the S1 map light assembly (telephone microphone assembly) connector.
| *a | Component with harness connected
(Radio and Display Receiver Assembly) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F71-4 (MACC) - Body ground | Ignition switch ACC | 4 to 6 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F71-18 (SGND) - Body ground | Always | Below 1 Ω |
| F71-19 (MIN-) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the map light assembly (telephone microphone assembly).
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
| *a | Component without harness connected
(Map Light Assembly (Telephone Microphone Assembly)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 13 (SNS2) - 4 (MCO-) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the F71 radio and display receiver assembly connector.
Reconnect the S1 map light assembly (telephone microphone assembly) connector.
Turn the ignition switch to ACC.
| *a | Component with harness connected
(Map Light Assembly (Telephone Microphone Assembly)) |
Connect an oscilloscope to terminals 2 (MCO+) and 4 (MCO-) of the S1 map light assembly (telephone microphone assembly) connector.
Check the waveform of the map light assembly (telephone microphone assembly) using the oscilloscope.
| Result | Proceed to |
|---|---|
| A waveform synchronized with the voice input to the map light assembly (telephone microphone assembly) is output. | A |
| A waveform synchronized with the voice input to the map light assembly (telephone microphone assembly) is not output. | B |
A
B
Disconnect the F71 radio and display receiver assembly connector.
Disconnect the S1 map light assembly (telephone microphone assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F71-6 (SNS2) - S1-13 (SNS2) | Always | Below 1 Ω |
| F71-6 (SNS2) or S1-13 (SNS2) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F71 radio and display receiver assembly connector.
Disconnect the F140 telematics transceiver connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F71-5 (MIN+) - F140-18 (MCO+) | Always | Below 1 Ω |
| F71-19 (MIN-) - F140-19 (MCO-) | Always | Below 1 Ω |
| F71-5 (MIN+) or F140-18 (MCO+) - Body ground | Always | 10 kΩ or higher |
| F71-19 (MIN-) or F140-19 (MCO-) - Body ground | Always | 10 kΩ or higher |
| F71-18 (SGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F140 telematics transceiver connector.
Disconnect the S1 map light assembly (telephone microphone assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F140-33 (MCVD) - S1-3 (MACC) | Always | Below 1 Ω |
| F140-34 (MCI+) - S1-2 (MCO+) | Always | Below 1 Ω |
| F140-35 (MCI-) - S1-4 (MCO-) | Always | Below 1 Ω |
| F140-33 (MCVD) or S1-3 (MACC) - Body ground | Always | 10 kΩ or higher |
| F140-34 (MCI+) or S1-2 (MCO+) - Body ground | Always | 10 kΩ or higher |
| F140-35 (MCI-) or S1-4 (MCO-) - Body ground | Always | 10 kΩ or higher |
| F140-32 (SGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F140 telematics transceiver connector.
| *a | Component with harness connected
(Radio and Display Receiver Assembly) |
Reconnect the F71 radio and display receiver assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F71-18 (SGND) - Body ground | Always | Below 1 Ω |
| F71-19 (MIN-) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the F140 telematics transceiver connector.
| *a | Component with harness connected
(Telematics Transceiver) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F140-33 (MCVD) - Body ground | Ignition switch ACC | 4 to 6 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F140-35 (MCI-) - Body ground | Always | Below 1 Ω |
| F140-32 (SGND) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the map light assembly (telephone microphone assembly).
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
| *a | Component without harness connected
(Map Light Assembly (Telephone Microphone Assembly)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 13 (SNS2) - 4 (MCO-) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the F71 radio and display receiver assembly connector.
Reconnect the S1 map light assembly (telephone microphone assembly) connector.
Reconnect the F140 telematics transceiver connector.
Turn the ignition switch to ACC.
| *a | Component with harness connected
(Map Light Assembly (Telephone Microphone Assembly)) |
Connect an oscilloscope to terminals 2 (MCO+) and 4 (MCO-) of the S1 map light assembly (telephone microphone assembly) connector.
Check the waveform of the map light assembly (telephone microphone assembly) using the oscilloscope.
| Result | Proceed to |
|---|---|
| A waveform synchronized with the voice input to the map light assembly (telephone microphone assembly) is output. | A |
| A waveform synchronized with the voice input to the map light assembly (telephone microphone assembly) is not output. | B |
A
B